Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › IGNITION SYSTEM
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254967 IGNITION SYSTEM G

1UR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 19100P 1.PERFORM SPARK TEST

a.

Check for DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

NOTICE:

If any DTC is output, perform troubleshooting procedures for that DTC.



b.

Check if sparks occur.

i.

Remove the ignition coils and spark plugs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).


ii.

Install the spark plug to the ignition coil and connect the ignition coil connector.


iii.

Disconnect the 8 injector connectors.


iv.

Ground the spark plug.


v.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.

·

Do not crank the engine for more than 2 seconds.

For vehicles with a cranking hold function, turn the engine switch off during cranking to stop cranking.

·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.




vi.

If sparks do not occur normally in 1 or more cylinders, perform the "Ignition Coil and Spark Test" below.



Hide 2.INSPECT IGNITION COIL AND SPARK PLUG

a.

Spark test flowchart.

i.

Check that the wire harness side connector of the ignition coil is securely connected.

Result
Result Proceed to
NG Connect securely
OK Go to next step


ii.

Perform a spark test on each ignition coil.

1.

If there is a cylinder where sparks do not occur, replace its ignition coil with the ignition coil of a cylinder where sparks occur normally.

2.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating ignition coil.


Result
Result Proceed to
OK Replace ignition coil
NG Go to next step


iii.

Check the power supply to the ignition coil.

1.

Turn the engine switch on (IG).

2.

Check that there is battery voltage at the ignition coil positive (+) terminal.


Result
Result Proceed to
NG Check wiring between battery and ignition coil
OK Go to next step


iv.

Inspect the spark plug.

1.

Replace the spark plug with a normal one.

2.

Perform a spark test.


Result
Result Proceed to
OK Replace spark plug
NG Inspect the ignition system (See page (Click here))

NOTICE:
·

If an ignition coil assembly is struck or dropped, replace it with a new one.

·

If a spark plug is struck or dropped, replace it with a new one.




v.

Connect the 8 injector connectors.


vi.


Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



a.

Check the electrode.

i.
A110413E09
1.804,2.986 1.993,3.133 0.189,0.147 10 *1 1.39,2.914 1.608,3.074 1.608,3.074 1.748,3.074 false

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher


Text in Illustration
*1 Ground

If the result is not as specified, replace the spark plug.

HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method:

i.

Start the engine.*


ii.

Quickly accelerate the engine to 4000 rpm 5 times.*

NOTICE:

*: Do not perform this step if P0300 (misfire detection) or a related DTC is stored.



iii.

Remove the spark plug.


iv.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its threads and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Type
DENSO SK20HR11



d.
U110721

Check the spark plug electrode gap.

Maximum electrode gap for a used spark plug:

1.3 mm (0.0512 in.)


If the gap is more than the maximum, replace the spark plug.

Electrode gap for a new spark plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)


NOTICE:

If adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.


If the electrode has traces of wet carbon, allow it to dry and then clean it with a spark plug cleaner.

Standard air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.