Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › THROTTLE BODY
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254969 THROTTLE BODY A

1UR-FE ENGINE CONTROL  THROTTLE BODY  INSTALLATION  


PROCEDURE

Hide 22030 1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A230336E01
1.16,1.726 1.672,1.996 1.672,1.996 1.781,1.996 false 1.794,1.911 1.971,2.073 0.177,0.162 10 *1

Install the No. 4 water by-pass hose to the throttle body with motor assembly.

Text in Illustration
*1 Paint Mark

HINT:

When installing the hose, make sure the paint mark and clip are as shown in the illustration.



b.
A230335E01
2.444,0.065 2.621,0.227 0.177,0.162 10 *1 1.477,0.698 2.256,0.151 2.256,0.151 2.425,0.151 false

Install the No. 12 water by-pass hose to the throttle body with motor assembly.

Text in Illustration
*1 Paint Mark

HINT:

When installing the hose, make sure the paint mark and clip are as shown in the illustration.



c.
U163633E01
2.505,0.136 2.691,0.300 0.186,0.164 10 *1 1.736,0.422 2.389,0.218 2.389,0.218 2.498,0.218 false 2.722,0.639 2.908,0.803 0.186,0.164 10 *2 2.382,1.038 2.608,0.732 2.608,0.732 2.71,0.732 false

Align the protrusion of a new gasket with the groove of the intake manifold and install the gasket to the intake manifold.

Text in Illustration
*1 Groove
*2 Protrusion


d.

Install the throttle body with motor assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.
A271379E01
2.566,0.231 2.726,0.380 0.161,0.149 10 *c 2.476,1.357 2.662,1.507 0.186,0.149 10 *b 1.454,0.34 1.610,0.490 0.156,0.149 10 *a 2.985,0.811 2.575,1.248 2.575,1.248 2.575,1.348 false 2.043,0.801 1.727,0.437 1.727,0.437 1.634,0.437 false 3.121,0.622 2.85,0.324 2.85,0.324 2.753,0.324 false

Connect the throttle position sensor and control motor connector.


f.

Connect the No. 4 water by-pass hose and No. 12 water by-pass hose.

Text in Illustration
*a Paint Mark
*b 5 mm (0.197 in.)
*c 13 to 17 mm (0.511 to 0.669 in.)

HINT:

When connecting the No. 12 water by-pass hose, make sure the paint marks and clips are as shown in the illustration.



Hide 17705 2.INSTALL AIR CLEANER CAP AND HOSE

a.
A456916N01
1.875,2.396 2.333,2.594 0.458,0.198 10 false (A)

Install the air cleaner cap and hose.


b.

Attach the 4 clamps.


c.

Connect the mass air flow meter connector and attach the clamp.


d.

Connect the No. 2 PCV hose and No. 1 air hose.


e.

Tighten the hose clamp so that it is within the standard.

(A):

15 mm or less



Hide 51405A 5.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53805 6.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53806 7.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 9.PERFORM INITIALIZATION

NOTICE:
·

Be sure to perform this procedure after reassembling the throttle body with motor assembly or removing and reinstalling any throttle body component.

·

Perform the following procedure after replacing the ECM, throttle body with motor assembly or any throttle body components. The following procedure should also be performed if the throttle body is cleaned.

·

Be sure to perform this procedure after reconnecting the battery cable and replacing the ECM.



a.

Disconnect the EFI fuse, wait at least 60 seconds, and then reconnect the fuse.


b.

Turn the engine switch on (IG) without operating the accelerator pedal.

NOTICE:

If the accelerator pedal is operated, perform the above steps again.



c.

Connect the GTS to the DLC3 and clear the DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


d.

Start the engine and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

Standard:
Condition Engine Idle Speed
A/C switched off 650 to 750 rpm


NOTICE:
·

Be sure to perform this step with all accessories off.

·

Make sure that the shift lever is in N or P.




e.

Enter the following menus: Powertrain / Engine and ETC / Data List / Throttle Sensor Volt %. Fully depress the accelerator pedal and check that the value is 60% or more.


f.

Perform a road test and confirm that there are no abnormalities.