Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed.

WIRING DIAGRAM

A372454E01
4.721,1.956 4.980,2.155 0.259,0.199 10 1R 0.664,5.521 1.129,5.670 0.465,0.149 10 Battery 3.031,6.243 3.312,6.393 0.281,0.149 10 N1 3.031,6.407 3.736,6.559 0.705,0.152 10 Fuel Pump 3.774,5.376 3.872,5.521 0.098,0.145 10 5 2.884,5.376 2.986,5.518 0.102,0.142 10 4 3.043,5.58 3.241,5.733 0.197,0.153 10 B2 3.514,5.58 3.713,5.730 0.199,0.150 10 E2 2.865,5.086 3.014,5.242 0.148,0.156 10 1 3.774,5.082 3.903,5.238 0.129,0.156 10 2 2.894,4.852 3.107,5.001 0.213,0.149 10 FP 3.587,4.852 3.840,5.001 0.253,0.149 10 FP- 2.656,4.268 2.754,4.413 0.098,0.145 10 3 2.854,4.37 2.971,4.516 0.117,0.146 10 E 3.992,4.775 4.685,5.087 0.692,0.312 10 Fuel Pump ECU 5.867,6.215 6.828,6.403 0.961,0.188 10 A52*1, A38*2 6.152,6.398 6.485,6.547 0.333,0.149 10 ECM 5.609,0.742 5.923,0.918 0.313,0.176 10 34 5.909,0.837 6.317,0.982 0.408,0.145 10 MREL 5.595,4.261 5.811,4.448 0.216,0.187 10 52 5.881,4.261 6.176,4.417 0.295,0.156 10 FPC 3.99,4.611 4.357,4.801 0.367,0.190 10 N14 0.652,0.836 0.942,1.025 0.290,0.188 10 1S 2.266,2.665 3.760,2.876 1.494,0.211 10 No. 2 Integration Relay 2.455,1.786 3.611,1.985 1.156,0.199 10 EFI MAIN NO. 1 1.752,2.119 2.662,2.321 0.910,0.202 10 FUEL PMP 0.505,3.957 1.117,4.149 0.612,0.193 10 P/I-B 4.461,1.052 4.718,1.245 0.258,0.193 10 11 4.769,0.66 5.027,0.853 0.258,0.193 10 8 0.692,0.655 0.950,0.848 0.258,0.193 10 4 4.703,0.829 4.993,1.017 0.290,0.188 10 1S 4.715,1.158 5.005,1.347 0.290,0.188 10 1S 5.679,1.069 5.882,1.268 0.202,0.199 10 3 5.909,1.181 6.393,1.374 0.483,0.193 10 +B 5.679,1.373 5.902,1.548 0.223,0.176 10 2 5.909,1.498 6.393,1.683 0.483,0.185 10 +B2 1.586,1.613 2.742,1.813 1.156,0.199 10 EFI MAIN NO. 1 3.699,2.282 4.610,2.484 0.910,0.202 10 FUEL PMP 4.764,1.771 5.022,1.964 0.258,0.193 10 6 4.526,1.379 4.784,1.572 0.258,0.193 10 7 4.706,1.471 4.996,1.660 0.290,0.188 10 1R 3.969,3.575 4.336,3.765 0.367,0.190 10 6 3.674,3.673 4.042,3.863 0.367,0.190 10 +B 3.555,4.359 3.923,4.549 0.367,0.190 10 FPC 3.976,4.254 4.343,4.444 0.367,0.190 10 5 4.511,5.871 5.408,6.041 0.897,0.169 10 *1: for RHD 4.511,6.228 5.408,6.398 0.897,0.169 10 *2: for LHD 0.711,1.772 0.839,1.937 0.128,0.165 10 1 0.652,1.95 0.914,2.132 0.262,0.182 10 1X 0.675,2.127 0.938,2.309 0.262,0.182 10 *1 1.033,1.772 1.161,1.937 0.128,0.165 10 1 0.993,1.95 1.255,2.132 0.262,0.182 10 1Y 0.993,2.127 1.255,2.309 0.262,0.182 10 *2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP/SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


e.

Check whether operating sounds can be heard while operating the fuel pump using the GTS.

OK:

Operating sounds can be heard from fuel pump.



Result
Result Proceed to
NG A
OK B


OK

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)

NG

8.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP)
A243665E01
2.862,1.37 2.973,1.519 0.111,0.149 10 1 0.647,1.391 0.755,1.544 0.107,0.152 10 2 1.931,1.67 2.821,1.462 false 1.539,1.671 0.796,1.478 false 0.178,0.144 2.543,0.541 2.365,0.397 10 Component with harness connected: (Fuel Pump)

a.

Remove the fuel tank assembly (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL TANK>REMOVAL).


b.

Remove the fuel pump from the fuel tank assembly.


c.

Clean the fuel pump to completely remove any remaining fuel.


d.

Connect the fuel pump connector.

CAUTION:

Confirm that no fuel remains inside or on the outside of the fuel pump.



e.

Connect the GTS to the DLC3.


f.

Turn the engine switch on (IG).


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Duty.


i.

Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
1 - 2 FPC Duty: 25% 3.2 to 4.05 V
FPC Duty: 80% 8.8 to 12.5 V



j.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


k.

Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
1 - 2 ON (FPC Duty: 90%) 9.0 to 14.0 V



HINT:
·

Be sure to measure the voltage with all of the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)

NG

6.REPLACE FUEL PUMP ECU
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
N14-5 (FPC) - A52-52 (FPC) Always Below 1 Ω
N14-5 (FPC) or A52-52 (FPC) - Body ground Always 10 kΩ or higher


Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
N14-5 (FPC) - A38-52 (FPC) Always Below 1 Ω
N14-5 (FPC) or A38-52 (FPC) - Body ground Always 10 kΩ or higher




OK

4.REPLACE FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE FUEL PUMP
a.

Replace the fuel pump (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL PUMP>REMOVAL).



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

6.REPLACE FUEL PUMP ECU
a.

Replace the fuel pump ECU.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.




OK

END

NG

8.INSPECT FUEL PUMP ECU (POWER SOURCE VOLTAGE)
U163418E01
2.404,1.917 2.598,2.070 0.194,0.152 10 +B 2.212,1.446 2.506,1.903 false 0.25,1.227 0.587,1.407 0.338,0.180 10 N14 0.048,0.039 2.400,0.383 2.353,0.344 10 Front view of wire harness connector: (to Fuel Pump ECU)

a.

Disconnect the fuel pump ECU connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N14-6 (+B) - Body Ground Engine switch on (IG) 11 to 14 V




OK

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)

NG

12.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - FUEL PUMP ECU)
9.CHECK HARNESS AND CONNECTOR (FUEL PUMP - FUEL PUMP ECU)
a.

Disconnect the fuel pump connector.


b.

Disconnect the fuel pump ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-4 (B2) - N14-1 (FP) Always Below 1 Ω
N1-5 (E2) - N14-2 (FP-) Always Below 1 Ω
N1-4 (B2) or N14-1 (FP) - Body ground Always 10 kΩ or higher
N1-5 (E2) or N14-2 (FP-) - Body ground Always 10 kΩ or higher




OK

10.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FUEL PUMP
a.


OK

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)

NG

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM, BODY GROUND)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
A52-52 (FPC) - N14-5 (FPC) Always Below 1 Ω
N14-3 (E) - Body ground Always Below 1 Ω
A52-52 (FPC) or N14-5 (FPC) - Body ground Always 10 kΩ or higher


Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
A38-52 (FPC) - N14-5 (FPC) Always Below 1 Ω
N14-3 (E) - Body ground Always Below 1 Ω
A38-52 (FPC) or N14-5 (FPC) - Body ground Always 10 kΩ or higher




OK

REPLACE FUEL PUMP ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - FUEL PUMP ECU)
a.

Disconnect the fuel pump ECU connector.


b.

Disconnect the No. 2 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1R-6 - N14-6 (+B) Always Below 1 Ω
1R-6 or N14-6 (+B) - Body ground Always 10 kΩ or higher




OK

13.INSPECT NO. 2 INTEGRATION RELAY (FUEL PMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT NO. 2 INTEGRATION RELAY (FUEL PMP)
a.

Inspect the No. 2 integration relay (FUEL PMP) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

NG

REPLACE NO. 2 INTEGRATION RELAY