1. DISCHARGE FUEL SYSTEM PRESSURE
77310A
2.REMOVE FUEL TANK CAP ASSEMBLY
77606
3.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Remove the 5 bolts and No. 1 fuel tank protector sub-assembly.
77209C
4.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)
Detach the fuel tube clamp.
Pull up the retainer and disconnect the fuel tank main tube sub-assembly.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
| *1 | Retainer |
| *2 | Pipe |
| *3 | Nylon Tube |
| *4 | Connector |
| *5 | O-Ring |
|
Pull Up |
5.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
| *1 | Retainer | *2 | Pipe |
| *3 | Nylon Tube | *4 | Connector |
| *5 | O-Ring | - | - |
| *a | except G.C.C. Countries | *b | for G.C.C. Countries |
|
Pull Up | - | - |
Detach the fuel tube clamp.
Pull up the retainer and disconnect the fuel tank main tube sub-assembly.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
6.DRAIN FUEL
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Do not smoke or be near an open flame when working on the fuel system.
Secure good ventilation.
Keep gasoline away from rubber or leather parts.
If the fuel pump does not operate, remove the tube joint clip and disconnect the fuel tank return tube sub-assembly, and drain fuel from the port shown in the illustration.
| *a | for Single Tank Type |
| *b | for Double Tank Type |
| *c | Port |
Disconnect the cable from the negative (-) battery terminal.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the fuel pump and fuel sender gauge connector.
| *a | for Single Tank Type |
| *b | for Double Tank Type |
7. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
8.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
71300S
9.REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
71400S
10.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
11.REMOVE REAR NO. 2 SEAT ASSEMBLY
for Face to Face Seat Type (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>REMOVAL)
except Face to Face Seat Type (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(except Face to Face Seat Type)>REMOVAL)
62520P
12.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH
w/ Sliding Roof (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>REMOVAL)
w/o Sliding Roof (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>REMOVAL)
62510P
13.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH
w/ Sliding Roof (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>REMOVAL)
w/o Sliding Roof (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>REMOVAL)
58510D
14.REMOVE FRONT FLOOR CARPET ASSEMBLY
Turn over the floor carpet.
Fold back the floor carpet so that the air duct can be removed.
58329F
15.REMOVE REAR FLOOR NO. 2 SERVICE HOLE COVER
w/ Rear Air Conditioning System:
Remove the 2 screws and air duct.
Remove the rear floor No. 2 service hole cover.
16.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Single Tank Type)
Detach the fuel tube clamp.
Pull up the retainer and disconnect the No. 2 fuel tank breather tube.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
| *1 | Retainer |
| *2 | Pipe |
| *3 | Nylon Tube |
| *4 | Connector |
| *5 | O-Ring |
|
Pull Up |
17.DISCONNECT NO. 2 FUEL TANK BREATHER HOSE (for Double Tank Type)
for G.C.C. Countries:
Detach the fuel tube clamp.
Slide the clip and disconnect the No. 2 fuel tank breather hose from the pipe.
77204A
18.DISCONNECT FUEL TANK RETURN TUBE (for Single Tank Type)
Detach the fuel tube clamp.
Pull up the retainer and disconnect the fuel tank return tube.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
| *1 | Retainer |
| *2 | Pipe |
| *3 | Nylon Tube |
| *4 | Connector |
| *5 | O-Ring |
|
Pull Up |
19.DISCONNECT FUEL TANK RETURN TUBE (for Double Tank Type)
| *1 | Retainer | *2 | Pipe |
| *3 | Nylon Tube | *4 | Connector |
| *5 | O-Ring | - | - |
| *a | except G.C.C. Countries | *b | for G.C.C. Countries |
|
Pull Up | - | - |
Detach the fuel tube clamp.
Pull up the retainer and disconnect the fuel tank return tube.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
77027B
20.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY (for Double Tank Type)
for G.C.C. Countries:
Detach the fuel tube clamp.
Pull up the retainer and disconnect the No. 1 fuel emission tube sub-assembly.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
| *1 | Retainer |
| *2 | Pipe |
| *3 | Nylon Tube |
| *4 | Connector |
| *5 | O-Ring |
|
Pull Up |
except G.C.C. Countries:
Detach the fuel tube clamp.
Pull the retainer up while pinching it on both sides by hand as shown in the illustration, and disconnect the No. 1 fuel emission tube sub-assembly.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
| *1 | Retainer |
| *2 | Connector |
| *3 | O-Ring |
| *4 | Pipe |
| *5 | Nylon Tube |
|
Push |
|
Pull Up |
77259E
21.DISCONNECT FUEL HOSE (for Double Tank Type)
for G.C.C. Countries:
Detach the fuel tube clamp.
Slide the clip and disconnect the fuel hose from the pipe.
77252A
22.DISCONNECT NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
| *1 | Retainer | *2 | Connector |
| *3 | O-Ring | *4 | Pipe |
| *5 | Nylon Tube | - | - |
| *a | except G.C.C. Countries | *b | for G.C.C. Countries |
|
Pull Up | - | - |
Detach the fuel tube clamp.
Pull up the retainer and disconnect the No. 2 fuel tank main tube sub-assembly.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
23.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Double Tank Type)
except G.C.C. Countries:
Detach the fuel tube clamp.
Pull up the retainer and disconnect the No. 2 fuel tank breather tube.
Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
Do not use any tools to separate the pipe and connector.
Do not forcefully bend or twist the nylon tube.
Check for foreign matter on the pipe seal surface. Clean if necessary.
Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
| *1 | Retainer |
| *2 | Connector |
| *3 | O-Ring |
| *4 | Pipe |
| *5 | Nylon Tube |
|
Pull Up |
24.DISCONNECT FUEL TANK BREATHER TUBE (for Single Tank Type)
Detach the fuel tube clamp.
Pull up the retainer and disconnect the fuel tank breather tube from the fuel tank to filler pipe sub-assembly.
Do not use any tools in this procedure.
Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
| *1 | Retainer |
|
Pull Up |
25.DISCONNECT FUEL TANK BREATHER TUBE (for Double Tank Type)
Detach the fuel tube clamp.
Pull up the retainer and disconnect the fuel tank breather tube from the fuel tank to filler pipe sub-assembly.
Do not use any tools in this procedure.
Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
| *1 | Retainer |
|
Pull Up |
26.DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Single Tank Type)
Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank to filler pipe sub-assembly.
27.DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Double Tank Type)
Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank to filler pipe sub-assembly.
77100U
28.REMOVE FUEL TANK SUB-ASSEMBLY
Place an engine lifter under the fuel tank sub-assembly.
Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank band sub-assemblies.
Slowly lower the engine lifter slightly.
29.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)
Remove the 2 tube joint clips and pull out the 2 fuel tube joints.
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
| *1 | Fuel Tube Joint |
| *2 | Tube Joint Clip |
| *3 | O-Ring |
| *4 | Fuel Suction Plate Sub-assembly |
Detach the clamp and remove the fuel tank main tube sub-assembly.
| *1 | Fuel Tank Main Tube Sub-assembly |
| *2 | Fuel Tank Return Tube Sub-assembly |
Detach the clamp and remove the fuel tank return tube sub-assembly.
77259E
30.REMOVE FUEL HOSE (for Double Tank Type)
for G.C.C. Countries:
Slide the clip and remove the fuel hose from the fuel suction tube sub-assembly.
31.REMOVE FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)
Remove the 3 tube joint clips and pull out the 3 fuel tube joints.
Remove any dirt and foreign matter on the fuel tube joint before performing this work.
Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
Perform this work by hand. Do not use any tools.
Do not forcibly bend, twist or turn the nylon tube.
Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.
| *1 | Fuel Tube Joint |
| *2 | Tube Joint Clip |
| *3 | O-Ring |
| *4 | Fuel Suction Plate Sub-assembly |
except G.C.C. Countries:
Detach the clamp and remove the fuel tank main tube sub-assembly.
| *1 | Fuel Tank Main Tube Sub-assembly |
| *2 | Fuel Tank Return Tube Sub-assembly |
| *3 | No. 2 Fuel Tank Main Tube Sub-assembly |
Detach the clamp and remove the fuel tank return tube sub-assembly.
Detach the 2 clamps and remove the No. 2 fuel tank main tube sub-assembly.
for G.C.C. Countries:
Detach the clamp and remove the fuel tank main tube sub-assembly.
| *1 | Fuel Tank Main Tube Sub-assembly |
| *2 | Fuel Tank Return Tube Sub-assembly |
| *3 | No. 2 Fuel Tank Main Tube Sub-assembly |
Detach the clamp and remove the fuel tank return tube sub-assembly.
Detach the 2 clamps and remove the No. 2 fuel tank main tube sub-assembly.
77020A
32.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
77213B
33.REMOVE FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp and remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.
77697
34.REMOVE NO. 1 FUEL TANK HEAT INSULATOR
Remove the fuel tube clamp from the No. 1 fuel tank heat insulator.
| *a | for G.C.C. Countries |
Using needle-nose pliers, remove the 4 clips shown in the illustration, and then remove the No. 1 fuel tank heat insulator.