While the engine is being cranked, current flows from terminal STAR of the main body ECU to the park/neutral position switch and also flows to terminal STA of the ECM (STA signal).
Refer to DTC P0617 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0617).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
This chart is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to Problem Symptoms Table (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value.
| Engine Switch Position | Starter Signal |
|---|---|
| On (IG) | OFF |
| START | ON |
OK
NG
Remove the starter relay (ST) from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Starter relay (ST) terminal 2 - Body ground | Engine cranking | 11 to 14 V |
| Starter relay (ST) terminal 1* - Body ground | Engine cranking | 11 to 14 V |
*: URJ202L-GNTEKC
The engine does not crank because the relay is not installed.
Reinstall the starter relay (ST).
OK
NG
Inspect the starter relay (ST) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the starter relay (ST) from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Starter relay (ST) terminal 1 - Body ground | Always | Below 1 Ω |
| Starter relay (ST) terminal 2* - Body ground | Always | Below 1 Ω |
*: URJ202L-GNTEKC
Reinstall the starter relay (ST).
OK
NG
Remove the starter relay (ST) from the engine room relay block.
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Starter relay (ST) terminal 1* - C24-5 (L) | Always | Below 1 Ω |
| Starter relay (ST) terminal 2 - C24-5 (L) | Always | Below 1 Ω |
| Starter relay (ST) terminal 1* or C24-5 (L) - Body ground | Always | 10 kΩ or higher |
| Starter relay (ST) terminal 2 or C24-5 (L) - Body ground | Always | 10 kΩ or higher |
*: URJ202L-GNTEKC
Reinstall the starter relay (ST).
Reconnect the park/neutral position switch connector.
OK
NG
Inspect the park/neutral position switch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).
OK
NG
(See pageDrivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
Disconnect the park/neutral position switch connector.
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C24-4 (B) - E1-8 (STR) | Always | Below 1 Ω |
| C24-4 (B) or E1-8 (STR) - Body ground | Always | 10 kΩ or higher |
Reconnect the park/neutral position switch connector.
Reconnect the main body ECU connector.
OK
NG