The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Refer to DTC P0300 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0300).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the fuel injector connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | a5-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 2 | a1-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 3 | a6-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 4 | a2-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 5 | a7-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 6 | a3-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 7 | a8-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 8 | a4-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
OK
NG
Inspect the fuel injector assembly (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL INJECTOR>INSPECTION).
OK
NG
Disconnect the fuel injector connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Cylinder | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| No. 1 | a5-1 - Body ground | Always | 10 kΩ or higher |
| a5-1 - C46-86 (#10) | Always | Below 1 Ω | |
| No. 2 | a1-1 - Body ground | Always | 10 kΩ or higher |
| a1-1 - C46-109 (#20) | Always | Below 1 Ω | |
| No. 3 | a6-1 - Body ground | Always | 10 kΩ or higher |
| a6-1 - C46-85 (#30) | Always | Below 1 Ω | |
| No. 4 | a2-1 - Body ground | Always | 10 kΩ or higher |
| a2-1 - C46-108 (#40) | Always | Below 1 Ω | |
| No. 5 | a7-1 - Body ground | Always | 10 kΩ or higher |
| a7-1 - C46-84 (#50) | Always | Below 1 Ω | |
| No. 6 | a3-1 - Body ground | Always | 10 kΩ or higher |
| a3-1 - C46-107 (#60) | Always | Below 1 Ω | |
| No. 7 | a8-1 - Body ground | Always | 10 kΩ or higher |
| a8-1 - C46-83 (#70) | Always | Below 1 Ω | |
| No. 8 | a4-1 - Body ground | Always | 10 kΩ or higher |
| a4-1 - C46-106 (#80) | Always | Below 1 Ω |
| Cylinder | Tester Connection | Condition | Specified Condition |
|---|---|---|---|
| No. 1 | a5-1 - Body ground | Always | 10 kΩ or higher |
| a5-1 - C45-86 (#10) | Always | Below 1 Ω | |
| No. 2 | a1-1 - Body ground | Always | 10 kΩ or higher |
| a1-1 - C45-109 (#20) | Always | Below 1 Ω | |
| No. 3 | a6-1 - Body ground | Always | 10 kΩ or higher |
| a6-1 - C45-85 (#30) | Always | Below 1 Ω | |
| No. 4 | a2-1 - Body ground | Always | 10 kΩ or higher |
| a2-1 - C45-108 (#40) | Always | Below 1 Ω | |
| No. 5 | a7-1 - Body ground | Always | 10 kΩ or higher |
| a7-1 - C45-84 (#50) | Always | Below 1 Ω | |
| No. 6 | a3-1 - Body ground | Always | 10 kΩ or higher |
| a3-1 - C45-107 (#60) | Always | Below 1 Ω | |
| No. 7 | a8-1 - Body ground | Always | 10 kΩ or higher |
| a8-1 - C45-83 (#70) | Always | Below 1 Ω | |
| No. 8 | a4-1 - Body ground | Always | 10 kΩ or higher |
| a4-1 - C45-106 (#80) | Always | Below 1 Ω |
OK
NG
Inspect the No. 2 integration relay (IG2 MAIN) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG