Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  P0305  Cylinder 5 Misfire Detected  P0306  Cylinder 6 Misfire Detected  P0307  Cylinder 7 Misfire Detected  P0308  Cylinder 8 Misfire Detected  


DESCRIPTION

A093767E21
2.302,0.906 2.49,1.073 0.188,0.167 10 false *3 0.531,0.219 0.698,0.385 0.167,0.167 10 false *1 0.531,1.729 0.708,1.885 0.177,0.156 10 false *2

Text in Illustration
*1 Camshaft Position Sensor
*2 Crankshaft Position Sensor
*3 ECM

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emissions levels. High concentrations of HC can also cause increases in the Three-way Catalytic Converter (TWC) temperature, which may cause damage to the Three-way Catalytic Converter (TWC). To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the Three-way Catalytic Converter (TWC) reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.

If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0300 Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (MIL blinks when detect immediately).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

High temperature misfire occurs in the Three-way Catalytic Converter (MIL blinks when detect immediately).

·

Catalyst deterioration misfire occurs (MIL illuminates).



When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause catalyst deterioration, is detected (2 trip detection logic).

·

An excessive misfiring rate (approximately 130 to 160 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following condition, which could cause damage to the three-way catalytic converter, is detected.

·

A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


WIRING DIAGRAM

A372452E01
5.998,0.608 6.279,0.764 0.281,0.156 10 #10 5.998,1.392 6.279,1.548 0.281,0.156 10 #20 5.998,2.198 6.279,2.354 0.281,0.156 10 #30 5.998,2.996 6.279,3.152 0.281,0.156 10 #40 5.998,3.809 6.279,3.965 0.281,0.156 10 #50 5.998,4.62 6.279,4.776 0.281,0.156 10 #60 5.998,5.426 6.279,5.582 0.281,0.156 10 #70 5.998,6.252 6.279,6.408 0.281,0.156 10 #80 6.017,7.245 6.321,7.401 0.304,0.156 10 E01 6.017,7.651 6.321,7.807 0.304,0.156 10 E02 6.379,8.341 6.730,8.497 0.351,0.156 10 ECM 6.084,8.168 7.037,8.337 0.953,0.169 10 C46*1, C45*2 5.764,7.654 5.975,7.845 0.211,0.191 10 42 5.764,7.248 5.986,7.456 0.222,0.207 10 43 5.666,6.252 5.933,6.401 0.267,0.149 10 106 5.666,4.62 5.933,4.769 0.267,0.149 10 107 5.753,5.426 5.933,5.578 0.180,0.152 10 83 5.753,3.809 5.933,3.961 0.180,0.152 10 84 5.68,2.996 5.933,3.145 0.253,0.149 10 108 5.75,2.198 5.933,2.347 0.184,0.149 10 85 5.666,1.392 5.933,1.541 0.267,0.149 10 109 5.757,0.608 5.933,0.750 0.177,0.142 10 86 4.322,0.602 4.432,0.754 0.111,0.152 10 2 4.322,1.388 4.432,1.541 0.111,0.152 10 2 4.322,2.189 4.432,2.341 0.111,0.152 10 2 4.322,3.003 4.432,3.155 0.111,0.152 10 2 4.322,3.817 4.432,3.970 0.111,0.152 10 2 4.322,4.618 4.432,4.770 0.111,0.152 10 2 4.322,5.432 4.432,5.585 0.111,0.152 10 2 4.322,6.24 4.432,6.393 0.111,0.152 10 2 5.222,0.607 5.336,0.763 0.114,0.156 10 1 5.222,1.392 5.336,1.547 0.114,0.156 10 1 5.222,2.19 5.336,2.346 0.114,0.156 10 1 5.222,3.003 5.336,3.159 0.114,0.156 10 1 5.222,3.815 5.336,3.971 0.114,0.156 10 1 5.222,4.614 5.336,4.770 0.114,0.156 10 1 5.222,5.427 5.336,5.582 0.114,0.156 10 1 5.226,6.245 5.340,6.401 0.114,0.156 10 1 4.383,1.085 5.247,1.262 0.864,0.177 10 No. 1 Injector 4.383,0.945 4.657,1.096 0.274,0.150 10 a5 4.383,2.556 4.657,2.707 0.274,0.150 10 a6 4.383,4.163 4.657,4.314 0.274,0.150 10 a7 4.383,5.779 4.657,5.929 0.274,0.151 10 a8 4.383,1.884 5.247,2.061 0.864,0.177 10 No. 2 Injector 4.383,1.744 4.681,1.894 0.298,0.150 10 a1 4.383,3.35 4.681,3.501 0.298,0.150 10 a2 4.383,4.971 4.681,5.121 0.298,0.150 10 a3 4.383,6.615 4.681,6.765 0.298,0.150 10 a4 4.383,2.697 5.247,2.873 0.864,0.177 10 No. 3 Injector 4.383,3.481 5.247,3.658 0.864,0.177 10 No. 4 Injector 4.383,4.302 5.247,4.478 0.864,0.177 10 No. 5 Injector 4.383,5.112 5.247,5.289 0.864,0.177 10 No. 6 Injector 4.383,5.915 5.247,6.092 0.864,0.177 10 No. 7 Injector 4.383,6.746 5.247,6.923 0.864,0.177 10 No. 8 Injector 3.249,0.841 3.502,1.004 0.253,0.163 10 INJ 1.251,0.848 1.942,1.024 0.691,0.175 10 IG2 MAIN 2.706,1.11 2.958,1.280 0.251,0.170 10 1S 2.705,0.686 2.961,0.856 0.256,0.170 10 1R 1.009,1.871 1.223,2.041 0.214,0.170 10 1R 2.756,0.507 2.904,0.669 0.149,0.162 10 1 2.756,0.941 2.893,1.120 0.137,0.179 10 4 1.307,1.874 1.452,2.051 0.145,0.178 10 2 1.154,3.044 1.339,3.203 0.186,0.159 10 3 1.508,2.121 3.168,2.304 1.661,0.184 10 No. 2 Integration Relay 0.952,3.291 1.509,3.466 0.557,0.175 10 IG1D 0.761,4.427 2.600,4.897 1.839,0.470 10 Certification ECU Assembly (Smart Key ECU Assembly) 0.761,4.253 1.167,4.427 0.406,0.174 10 E128 0.534,7.38 1.009,7.563 0.474,0.184 10 Battery 0.399,6.413 0.873,6.597 0.474,0.184 10 P/I-B 1.802,1.357 2.493,1.533 0.691,0.175 10 IG2 MAIN 1.629,8.02 2.526,8.190 0.897,0.169 10 *1: for RHD 1.629,8.378 2.526,8.547 0.897,0.169 10 *2: for LHD 0.582,0.506 0.710,0.672 0.128,0.165 10 1 0.535,0.686 0.797,0.868 0.262,0.182 10 1X 0.553,0.869 0.816,1.052 0.262,0.182 10 *1 0.915,0.506 1.043,0.672 0.128,0.165 10 1 0.866,0.684 1.129,0.866 0.262,0.182 10 1Y 0.89,0.869 1.152,1.052 0.262,0.182 10 *2

A278617E04
5.356,0.827 5.692,0.997 0.336,0.170 10 IGT1 3.1,0.912 3.437,1.081 0.336,0.170 10 IGT1 5.356,2.495 5.692,2.665 0.336,0.170 10 IGT3 5.356,4.162 5.692,4.332 0.336,0.170 10 IGT5 5.356,5.829 5.692,5.999 0.336,0.170 10 IGT7 5.358,1.236 5.689,1.405 0.331,0.169 10 IGF1 3.102,1.32 3.433,1.489 0.331,0.169 10 IGF1 5.083,0.825 5.296,0.981 0.213,0.156 10 40 5.083,2.478 5.303,2.634 0.220,0.156 10 37 5.083,4.145 5.276,4.301 0.193,0.156 10 35 5.083,5.813 5.285,5.969 0.202,0.156 10 38 5.004,1.216 5.301,1.372 0.296,0.156 10 105 3.497,0.831 3.611,0.987 0.114,0.156 10 3 3.497,1.228 3.632,1.391 0.135,0.163 10 2 2.534,0.835 2.634,0.991 0.100,0.156 10 1 2.534,1.228 2.648,1.384 0.114,0.156 10 4 2.344,1.58 2.639,1.736 0.295,0.156 10 C4 2.344,1.748 4.171,1.918 1.827,0.170 10 No. 1 Ignition Coil Assembly 2.722,0.909 2.934,1.063 0.211,0.154 10 +B 2.722,1.316 3.072,1.472 0.350,0.156 10 GND 3.1,2.593 3.437,2.763 0.336,0.170 10 IGT3 3.102,3.002 3.433,3.171 0.331,0.169 10 IGF2 3.497,2.513 3.611,2.668 0.114,0.156 10 3 3.497,2.909 3.632,3.072 0.135,0.163 10 2 2.534,2.517 2.634,2.673 0.100,0.156 10 1 2.534,2.909 2.648,3.065 0.114,0.156 10 4 2.344,3.261 2.731,3.417 0.387,0.156 10 C130 2.344,3.429 4.588,3.599 2.244,0.170 10 No. 3 Ignition Coil Assembly 2.722,2.591 2.934,2.744 0.211,0.154 10 +B 2.722,2.997 3.072,3.153 0.350,0.156 10 GND 3.1,4.26 3.437,4.430 0.336,0.170 10 IGT5 3.102,4.669 3.433,4.838 0.331,0.169 10 IGF2 3.497,4.18 3.611,4.336 0.114,0.156 10 3 3.497,4.577 3.632,4.740 0.135,0.163 10 2 2.534,4.184 2.634,4.340 0.100,0.156 10 1 2.534,4.576 2.648,4.732 0.114,0.156 10 4 2.344,4.928 2.639,5.084 0.295,0.156 10 C8 2.344,5.097 4.227,5.266 1.883,0.170 10 No. 5 Ignition Coil Assembly 2.722,4.258 2.934,4.412 0.211,0.154 10 +B 2.722,4.664 3.072,4.820 0.350,0.156 10 GND 3.1,5.927 3.437,6.097 0.336,0.170 10 IGT7 3.102,6.336 3.433,6.505 0.331,0.169 10 IGF1 3.497,5.847 3.611,6.003 0.114,0.156 10 3 3.497,6.244 3.632,6.407 0.135,0.163 10 2 2.534,5.851 2.634,6.007 0.100,0.156 10 1 2.534,6.243 2.648,6.399 0.114,0.156 10 4 2.344,6.596 2.731,6.752 0.387,0.156 10 C131 2.344,6.764 4.143,6.934 1.799,0.170 10 No. 7 Ignition Coil Assembly 2.722,5.925 2.934,6.079 0.211,0.154 10 +B 2.722,6.332 3.072,6.487 0.350,0.156 10 GND 1.664,0.53 1.913,0.685 0.248,0.156 10 INJ 0.161,0.119 1.159,0.534 0.998,0.415 10 from IG2 MAIN Relay 0.258,7.548 0.386,7.718 0.128,0.170 10 A 1.534,7.548 1.662,7.718 0.128,0.170 10 B 4.21,7.548 4.338,7.718 0.128,0.170 10 C 4.448,7.548 4.576,7.718 0.128,0.170 10 D 5.42,6.749 5.757,6.919 0.336,0.170 10 ECM 5.42,6.544 6.309,6.700 0.889,0.156 10 C46*1, C45*2

A278618E03
5.364,0.926 5.733,1.091 0.368,0.165 10 IGT2 5.364,2.588 5.733,2.753 0.368,0.165 10 IGT4 5.364,4.251 5.733,4.416 0.368,0.165 10 IGT6 5.364,5.932 5.733,6.097 0.368,0.165 10 IGT8 5.364,1.337 5.715,1.520 0.350,0.184 10 IGF2 5.091,0.926 5.305,1.100 0.214,0.174 10 33 5.031,1.337 5.312,1.502 0.281,0.165 10 104 5.101,2.588 5.325,2.749 0.224,0.161 10 34 5.101,4.251 5.315,4.411 0.215,0.161 10 36 5.101,5.932 5.277,6.093 0.176,0.161 10 39 3.669,0.916 3.788,1.072 0.119,0.156 10 3 3.669,1.309 3.788,1.465 0.119,0.156 10 2 2.702,0.916 2.803,1.080 0.100,0.164 10 1 2.688,1.321 2.807,1.495 0.119,0.174 10 4 3.263,0.991 3.622,1.156 0.360,0.165 10 IGT2 2.88,1 3.101,1.156 0.221,0.156 10 +B 2.88,1.393 3.221,1.549 0.341,0.156 10 GND 3.254,1.393 3.604,1.549 0.350,0.156 10 IGF2 3.669,2.593 3.788,2.749 0.119,0.156 10 3 3.669,2.985 3.788,3.141 0.119,0.156 10 2 2.702,2.593 2.803,2.757 0.100,0.164 10 1 2.688,2.997 2.807,3.172 0.119,0.174 10 4 3.263,2.668 3.622,2.833 0.360,0.165 10 IGT4 2.88,2.677 3.101,2.833 0.221,0.156 10 +B 2.88,3.069 3.221,3.225 0.341,0.156 10 GND 3.254,3.069 3.604,3.225 0.350,0.156 10 IGF1 3.669,4.256 3.788,4.411 0.119,0.156 10 3 3.669,4.648 3.788,4.804 0.119,0.156 10 2 2.702,4.255 2.803,4.419 0.100,0.164 10 1 2.688,4.66 2.807,4.834 0.119,0.174 10 4 3.263,4.33 3.622,4.495 0.360,0.165 10 IGT6 2.88,4.34 3.101,4.495 0.221,0.156 10 +B 2.88,4.732 3.221,4.888 0.341,0.156 10 GND 3.254,4.732 3.604,4.888 0.350,0.156 10 IGF1 3.669,5.927 3.788,6.083 0.119,0.156 10 3 3.669,6.32 3.788,6.476 0.119,0.156 10 2 2.702,5.927 2.803,6.091 0.100,0.164 10 1 2.688,6.332 2.807,6.506 0.119,0.174 10 4 3.263,6.002 3.622,6.167 0.360,0.165 10 IGT8 2.88,6.012 3.101,6.167 0.221,0.156 10 +B 2.88,6.404 3.221,6.560 0.341,0.156 10 GND 3.254,6.404 3.604,6.560 0.350,0.156 10 IGF2 5.444,6.903 5.785,7.069 0.341,0.165 10 ECM 0.255,0.094 0.393,0.260 0.139,0.165 10 A 1.525,0.094 1.664,0.260 0.139,0.165 10 B 4.192,0.094 4.330,0.260 0.139,0.165 10 C 4.434,0.094 4.573,0.260 0.139,0.165 10 D 0.655,7.417 1.005,7.573 0.350,0.156 10 C132 0.655,7.567 1.399,7.912 0.744,0.346 10 Noise Filter (for Bank 1) 2.384,7.417 2.748,7.573 0.364,0.156 10 C135 2.384,7.567 3.128,7.912 0.744,0.346 10 Noise Filter (for Bank 2) 1.614,7.427 1.724,7.587 0.110,0.161 10 1 2.1,7.427 2.210,7.587 0.110,0.161 10 1 2.368,1.657 2.737,1.823 0.369,0.165 10 C134 2.368,1.807 4.191,1.991 1.822,0.184 10 No. 2 Ignition Coil Assembly 2.368,3.339 2.682,3.504 0.313,0.165 10 C13 2.368,3.488 4.163,3.672 1.795,0.184 10 No. 4 Ignition Coil Assembly 2.368,5.001 2.737,5.166 0.369,0.165 10 C133 2.368,5.151 4.237,5.334 1.869,0.184 10 No. 6 Ignition Coil Assembly 2.368,6.664 2.682,6.829 0.313,0.165 10 C53 2.368,6.813 4.172,6.997 1.804,0.184 10 No. 8 Ignition Coil Assembly 4.322,7.589 5.089,7.752 0.767,0.163 10 *1: for RHD 4.322,7.848 5.089,8.011 0.767,0.163 10 *2: for LHD 5.444,6.697 6.378,6.862 0.934,0.165 10 C46*1, C45*2

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE).

7.

Read the misfire counts of each cylinder (cylinder No. 1 to No. 8) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

8.

Drive the vehicle several times with the conditions, such as engine speed and engine load, as shown in Misfire RPM and Misfire Load in the freeze frame data.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.

Engine Speed Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the engine switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTCs, freeze frame data and other data will be cleared.


10.

Record the DTCs, freeze frame data and misfire counts.

11.

Turn the engine switch off and wait for at least 30 seconds.

12.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).


CAUTION / NOTICE / HINT

HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors may be a cause of the problem:

(a)

The fuel level is low.

(b)

Improper fuel is being used.

(c)

The spark plugs are dirty.


·

After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after the repairs.

·

For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speed. If misfires only occur during high engine speed driving, only DTC P0300 is stored.

In the event of DTC P0300 being output, perform the following operations:

(b)

Start the engine and conduct the confirmation driving pattern.

(c)

Read the misfiring rates of each cylinder or the DTCs using the GTS.

(d)

Repair the cylinders that have a high misfiring rate or are indicated by the DTCs.

(e)

After finishing repairs, conduct the confirmation driving pattern again in order to verify that DTC P0300 is not stored.


·

When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).

·

When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires may have occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 is output A
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections (See page Engine / Hybrid System>1UR-FE (EMISSION CONTROL)>EMISSION CONTROL SYSTEM(w/ Secondary Air Injection System)>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.


e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.




NEXT

4.READ VALUE USING GTS (MISFIRE COUNT)
4.READ VALUE USING GTS (MISFIRE COUNT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Rate, #2, #3, #4, #5, #6, #7 and #8.


f.

Allow the engine to idle.


g.

Read each value for CYL #1 to #8 (Cylinder #1 Misfire Rate to #8) displayed on the GTS. If no misfire counts occur in any cylinders, perform the following procedures:

i.

Move the shift lever to D.


ii.

Check CYL #1 to #8 (Cylinder #1 Misfire Rate to #8).


iii.

If misfire counts are still not displayed, perform procedure "A" and "B", and then check the misfire counts again.

Procedure A: Drive the vehicle while satisfying the Misfire RPM and Misfire Load values noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedure above.

Procedure B: Read CYL #1 to #8 (Cylinder #1 Misfire Rate to #8) or the DTCs output on the GTS.

Result
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B

HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data's record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data's record of the Engine Run Time is less than 120 seconds, the misfire may be detected immediately after the engine is started.






A

5.INSPECT SPARK PLUG

B

16.CHECK AIR INDUCTION SYSTEM
5.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

6.CHECK FOR SPARKS AND IGNITION

NG

6.CHECK FOR SPARKS AND IGNITION
a.

Perform a spark test (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

7.CHECK CYLINDER COMPRESSION PRESSURE
7.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

OK

9.CHECK HARNESS AND CONNECTOR

NG

9.CHECK HARNESS AND CONNECTOR

OK

10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL INJECTOR>INSPECTION).



OK

11.CHECK AIR INDUCTION SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage in air induction system.




OK

12.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

12.CHECK FUEL PRESSURE

OK

13.READ VALUE USING GTS (COOLANT TEMP)

NG

32.CHECK FUEL LINE
13.READ VALUE USING GTS (COOLANT TEMP)

OK

14.READ VALUE USING GTS (MAF)

NG

14.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.3 gm/s. and 25.8 gm/s. (shift lever: N; A/C: Off).




OK

15.CHECK VALVE TIMING

NG

27.CHECK HARNESS AND CONNECTOR
15.CHECK VALVE TIMING

OK

27.CHECK HARNESS AND CONNECTOR

NG

16.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>1UR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage in air induction system.




OK

17.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

17.CHECK FUEL PRESSURE

OK

18.READ VALUE USING GTS (COOLANT TEMP)

NG

32.CHECK FUEL LINE
18.READ VALUE USING GTS (COOLANT TEMP)

OK

19.READ VALUE USING GTS (MAF)

NG

19.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.3 gm/sec. and 25.8 gm/sec. (shift lever: N; A/C: Off).




OK

20.CHECK VALVE TIMING

NG

27.CHECK HARNESS AND CONNECTOR
20.CHECK VALVE TIMING

OK

21.INSPECT SPARK PLUG

NG

21.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

22.CHECK FOR SPARKS AND IGNITION

NG

22.CHECK FOR SPARKS AND IGNITION
a.

Perform a spark test (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

23.CHECK CYLINDER COMPRESSION PRESSURE
23.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>1UR-FE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

24.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

24.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

OK

25.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

NG

25.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR - ECM)

OK

26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL INJECTOR>INSPECTION).



OK

27.CHECK HARNESS AND CONNECTOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

27.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS
28.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


k.

Check the DTC judgment result.

Result
Display (DTC Output) Proceed to
ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
A
NORMAL
(No DTC output)
B



A

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C46-74 (VG) Always Below 1 Ω
C50-2 (E2G) - C46-75 (E2G) Always Below 1 Ω
C50-3 (VG) or C46-74 (VG) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-74 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-75 (E2G) Always Below 1 Ω
C50-3 (VG) or C45-74 (VG) - Body ground Always 10 kΩ or higher




OK

30.REPLACE MASS AIR FLOW METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.REPLACE MASS AIR FLOW METER ASSEMBLY
a.

Replace the mass air flow meter assembly (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).

HINT:

If the results of the inspections performed in steps 14 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter assembly.




NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG) and turn the GTS on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


k.

Check the DTC judgment result.

Result
Display (DTC Output) Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
B



A

END

B

32.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

NG

REPAIR OR REPLACE FUEL LINE