The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Refer to ECM Power Source Circuit (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit).
VC Output Circuit
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI No. 2 fuse) - Body ground | Engine switch on (IG) | 11 to 14 V |
| *1 | Engine Room Relay Block |
| *2 | EFI No. 2 Fuse |
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
OK
NG
Disconnect the throttle body connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the accelerator pedal position sensor connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the manifold absolute pressure sensor connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the air switching valve (for Bank 1) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the air switching valve (for Bank 2) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the power steering oil pressure sensor connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the camshaft position sensor connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the crankshaft position sensor connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Turn the engine switch on (IG).
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the throttle body connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the air switching valve connector (for Bank 1).
Disconnect the air switching valve connector (for Bank 2).
Disconnect the power steering oil pressure switch connector.
Disconnect the camshaft position sensor connector.
Disconnect the crankshaft position sensor connector.
Disconnect the VVT sensor (for Intake Side of Bank 1) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 1) connector.
Disconnect the VVT sensor (for Intake Side of Bank 2) connector.
Disconnect the VVT sensor (for Exhaust Side of Bank 2) connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-80 (VCTA) - Body ground | Always | 10 kΩ or higher |
| A52-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A52-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C46-66 (VCV2) - Body ground | Always | 10 kΩ or higher |
| C46-67 (VCV1) - Body ground | Always | 10 kΩ or higher |
| 1S-11 - A52-3 (+B) | Always | Below 1 Ω |
| 1S-11 - A52-2 (+B2) | Always | Below 1 Ω |
| 1S-11 or A52-3 (+B) - Body ground | Always | 10 kΩ or higher |
| 1S-11 or A52-2 (+B2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-80 (VCTA) - Body ground | Always | 10 kΩ or higher |
| A38-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A38-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C45-66 (VCV2) - Body ground | Always | 10 kΩ or higher |
| C45-67 (VCV1) - Body ground | Always | 10 kΩ or higher |
| 1S-11 - A38-3 (+B) | Always | Below 1 Ω |
| 1S-11 - A38-2 (+B2) | Always | Below 1 Ω |
| 1S-11 or A38-3 (+B) - Body ground | Always | 10 kΩ or higher |
| 1S-11 or A38-2 (+B2) - Body ground | Always | 10 kΩ or higher |
OK
NG