Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  Pre-heating Control Circuit  


DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates a time interval of the current that needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned to ON. The ECM then turns on the glow plug relay and permits current to flow through the glow plug based on the ECM calculated time. The glow plug is then heated, and enhances fuel combustion with a cold engine.

This DTC will be stored if the glow plug or the circuit is open.

A154593E08
0.549,1.099 1.062,1.477 0.513,0.378 10 from Battery 0.162,0.114 2.029,0.318 1.867,0.204 10 Glow System Wiring Diagram 1.532,0.927 2.257,1.074 0.725,0.147 10 GLOW1 3.249,1.781 3.833,1.962 0.584,0.181 10 GLOW1 5.229,1.194 5.707,1.367 0.478,0.173 10 GREL 0.736,2.874 1.800,3.076 1.063,0.202 10 No. 1 Glow Plug 5.836,2.636 6.241,2.801 0.406,0.165 10 ECM

HINT:
·

These troubleshooting procedures are for: 1) difficult engine starting in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after engine is started.

·

After the engine is started, the ECM performs an "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.



A384648E02
0.125,0.094 1.354,0.323 1.229,0.229 10 false After-glow System 1.344,0.271 2.333,0.656 0.99,0.385 10 false After-glow Time (Second) 2.448,0.552 2.75,0.719 0.302,0.167 10 false 120 2.573,1.281 2.76,1.448 0.188,0.167 10 false 1 2.74,1.458 2.927,1.625 0.188,0.167 10 false 0 3.156,1.458 3.344,1.625 0.188,0.167 10 false 20 4.031,1.448 4.219,1.615 0.188,0.167 10 false 40 4.656,1.448 4.906,1.646 0.25,0.198 10 false °C 3.115,1.604 3.427,1.823 0.313,0.219 10 false (68) 3.958,1.583 4.344,1.802 0.385,0.219 10 false (104) 4.625,1.583 5.01,1.802 0.385,0.219 10 false (°F) 2.813,1.792 4.656,2.01 1.844,0.219 10 false Engine Coolant Temperature 4.385,2.063 4.677,2.26 0.292,0.198 10 false ON 2.427,2.438 2.656,2.625 0.229,0.188 10 false off 2.406,3.219 2.771,3.406 0.365,0.188 10 false OFF 4.344,2.844 4.708,3.031 0.365,0.188 10 false ON 5.865,3.229 6.229,3.417 0.365,0.188 10 false OFF 1.219,2.51 2.167,2.719 0.948,0.208 10 false Ignition Switch 1.448,3.333 2.198,3.552 0.75,0.219 10 false Glow Plug 1.229,4.094 2.177,4.302 0.948,0.208 10 false Engine Speed 2.865,4.469 3.813,4.677 0.948,0.208 10 false Engine Starts 4.219,4.385 5.25,4.573 1.031,0.188 10 false After-glow Time

WIRING DIAGRAM

A182513E07
0.813,6.823 1.302,7.01 0.49,0.188 10 false Battery 1.823,6.823 2.313,7.01 0.49,0.188 10 false Battery 0.26,4.771 0.385,4.917 0.125,0.146 10 false 1 0.479,4.802 0.75,5 0.271,0.198 10 false 1J 1.51,4.281 1.781,4.458 0.271,0.177 10 false 1N 1.51,0.865 1.813,1.031 0.302,0.167 10 false 1M 1.552,4.073 1.677,4.219 0.125,0.146 10 false 1 1.573,0.635 1.698,0.781 0.125,0.146 10 false 1 3.938,1.24 4.083,1.385 0.146,0.146 10 false 1 4.469,1.229 4.635,1.406 0.167,0.177 10 false 1 3.917,2.531 4.073,2.688 0.156,0.156 10 false 1 4.458,2.531 4.583,2.698 0.125,0.167 10 false 1 3.938,4.583 4.063,4.729 0.125,0.146 10 false 1 4.469,4.583 4.594,4.729 0.125,0.146 10 false 1 3.938,5.875 4.063,6.021 0.125,0.146 10 false 1 4.469,5.875 4.594,6.021 0.125,0.146 10 false 1 0.74,4.438 1.365,4.604 0.625,0.167 10 false GLOW 2 0.74,1.021 1.365,1.188 0.625,0.167 10 false GLOW 1 0.906,5.021 1.802,5.385 0.896,0.365 10 false Engine Room Relay Block 4.75,2.75 5.646,3.146 0.896,0.396 10 false Engine Room Relay Block 4.802,6.104 5.688,6.469 0.885,0.365 10 false Engine Room Relay Block 2.281,3.083 2.604,3.24 0.323,0.156 10 false C77 2.281,3.25 3.031,3.615 0.75,0.365 10 false No. 1 Glow Plug 3.375,7.188 3.688,7.375 0.313,0.188 10 false C78 3.375,7.333 4.458,7.531 1.083,0.198 10 false No. 2 Glow Plug 4.771,1.802 5.354,1.99 0.583,0.188 10 false GLOW 1 4.771,5.177 5.49,5.365 0.719,0.188 10 false GLOW 2 3.844,1.479 3.979,1.625 0.135,0.146 10 false 5 4.552,1.479 4.688,1.625 0.135,0.146 10 false 2 3.844,2.281 3.979,2.469 0.135,0.188 10 false 3 4.552,2.281 4.688,2.427 0.135,0.146 10 false 1 3.854,2.917 3.99,3.063 0.135,0.146 10 false 1 3.844,4.813 3.979,4.958 0.135,0.146 10 false 5 4.552,4.813 4.688,4.958 0.135,0.146 10 false 2 3.844,5.615 3.979,5.76 0.135,0.146 10 false 3 4.552,5.615 4.688,5.76 0.135,0.146 10 false 1 6.146,0.813 6.563,0.99 0.417,0.177 10 false GREL 5.865,0.969 6.052,1.146 0.188,0.177 10 false 63 6.146,4.25 6.563,4.427 0.417,0.177 10 false GRL2 5.865,4.396 6.052,4.573 0.188,0.177 10 false 62 5.979,6.906 6.938,7.083 0.958,0.177 10 false C45*1, C46*2 5.979,7.083 6.354,7.26 0.375,0.177 10 false ECM 4.917,6.948 5.677,7.146 0.76,0.198 10 false *1: for LHD 4.917,7.25 5.677,7.448 0.76,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

PROCEDURE

1.CHECK ECM TERMINAL VOLTAGE (GREL TERMINAL)
a.
A182516E01
0.146,0.034 2.552,0.443 2.406,0.409 10 Front view of wire harness connector: (to Engine Room Relay Block) 0.57,4.113 1.181,4.276 0.611,0.163 10 GLOW 1 1.627,4.113 2.242,4.276 0.614,0.163 10 GLOW 2

Remove the GLOW 1 relay from the engine room relay block.


b.

Remove the GLOW 2 relay from the engine room relay block.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GLOW 1 relay (2) - Body ground Ignition switch ON 11 to 14 V
GLOW 2 relay (2) - Body ground Ignition switch ON 11 to 14 V




OK

2.INSPECT GLOW RELAY (GLOW 1 or 2)

NG

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)
2.INSPECT GLOW RELAY (GLOW 1 or 2)

OK

3.INSPECT FUSE (GLOW 1 and GLOW 2)

NG

REPLACE GLOW RELAY (GLOW 1 or 2)

3.INSPECT FUSE (GLOW 1 and GLOW 2)
A182514E01
0.126,0.01 2.025,0.200 1.899,0.191 10 Engine Room Relay Block: 0.332,2.895 0.884,3.079 0.551,0.184 10 GLOW1 1.252,2.895 1.801,3.079 0.549,0.184 10 GLOW2 0.876,2.043 0.662,2.861 false 0.977,2.048 1.493,2.851 false

a.

Remove the GLOW 1 and GLOW 2 fuses from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Component Condition Specified Condition
GLOW 1 H-fuse Always Below 1 Ω
GLOW 2 H-fuse Always Below 1 Ω




OK

4.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

NG

CHECK FOR SHORT IN ALL HARNESSES AND COMPONENTS CONNECTED TO FUSE, AND REPLACE FUSE

4.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE)

OK

5.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)

NG

5.CHECK GLOW PLUG ASSEMBLY (INSTALLATION)
a.

Check the glow plug installation (See page Engine / Hybrid System>1VD-FTV (STARTING)>GLOW PLUG>INSTALLATION).

OK:

Glow plugs are installed securely.




OK

6.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - GLOW PLUG - BATTERY AND BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - GLOW PLUG - BATTERY AND BODY GROUND)
a.

Remove the GLOW 1 relay from the engine room relay block.

A385293E01
4.646,1.156 5.052,1.417 0.406,0.26 5.448,1.156 5.854,1.417 0.406,0.26 0.771,0.042 3.083,0.417 2.313,0.375 10 false Front view of wire harness connector: (to Engine Room Relay Block) 4.094,0.104 6.406,0.479 2.313,0.375 10 false Front view of wire harness connector: (to Glow Plug Connector) 4.729,1.219 5.188,1.417 0.458,0.198 10 false C77 5.521,1.198 5.979,1.396 0.458,0.198 10 false C78 5.094,1.063 5.406,1.26 0.313,0.198 10 false *1 5.906,1.063 6.219,1.26 0.313,0.198 10 false *2 4.198,2.448 5.01,2.646 0.813,0.198 10 false *1: No. 1 4.188,2.823 5,3.021 0.813,0.198 10 false *2: No. 2 1.479,3.406 2.292,3.604 0.813,0.198 10 false GLOW 1 2.365,3.406 3.031,3.604 0.667,0.198 10 false GLOW 2


b.

Disconnect the C77 glow plug connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 1
Tester Connection Condition Specified Condition
GLOW 1 relay (3) - C77-1 Always Below 1 Ω
GLOW 1 relay (5) - Positive (+) battery terminal cable Always Below 1 Ω
GLOW 1 relay (1) - Body ground Always Below 1 Ω



d.

Remove the GLOW 2 relay from the engine room relay block.


e.

Disconnect the C78 glow plug connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
No. 2
Tester Connection Condition Specified Condition
GLOW 2 relay (3) - C78-1 Always Below 1 Ω
GLOW 2 relay (5) - Positive (+) battery terminal cable Always Below 1 Ω
GLOW 2 relay (1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG RELAY - ECM AND BODY GROUND)
a.

Remove the GLOW 1 relay from the engine room relay block.

A385294E01
4.542,1.25 4.948,1.521 0.406,0.271 5.302,1.25 5.708,1.521 0.406,0.271 4.969,2.833 5.292,2.146 true 5.677,2.833 5.333,2.135 true 0.635,0.063 2.969,0.427 2.333,0.365 10 false Front view of wire harness connector: (to Engine Room Relay Block) 4.052,0.115 6.385,0.479 2.333,0.365 10 false Front view of wire harness connector: (to ECM) 4.615,1.313 4.99,1.5 0.375,0.188 10 false C45 5.385,1.302 5.76,1.49 0.375,0.188 10 false C46 4.979,1.167 5.292,1.365 0.313,0.198 10 false *1 5.75,1.156 6.063,1.354 0.313,0.198 10 false *2 1.219,3.375 1.917,3.583 0.698,0.208 10 false GLOW 1 2.125,3.385 2.823,3.594 0.698,0.208 10 false GLOW 2 4.625,2.854 5.365,3.063 0.74,0.208 10 false 62 (GRL2) 5.5,2.854 6.24,3.063 0.74,0.208 10 false 63 (GREL) 3.563,2.927 4.302,3.135 0.74,0.208 10 false *1: for LHD 3.563,3.271 4.302,3.479 0.74,0.208 10 false *2: for RHD


b.

Remove the GLOW 2 relay from the engine room relay block.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
GLOW 1 relay (2) - C45-63 (GREL) Always Below 1 Ω
GLOW 2 relay (2) - C45-62 (GRL2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
GLOW 1 relay (2) - C46-63 (GREL) Always Below 1 Ω
GLOW 2 relay (2) - C46-62 (GRL2) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
GLOW 1 relay (2) or C45-63 (GREL) - Body ground Always 10 kΩ or higher
GLOW 2 relay (2) or C45-62 (GRL2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
GLOW 1 relay (2) or C46-63 (GREL) - Body ground Always 10 kΩ or higher
GLOW 2 relay (2) or C46-62 (GRL2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR