Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the common rail system is controlled.

P0335
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Crank or start engine When the following condition is met (for 5 seconds during cranking or 0.5 seconds during engine start) (1 trip detection logic):
·

No crankshaft position sensor signal is sent to the ECM while cranking.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM



P0339
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine running at 1000 rpm or more with vehicle stationary No crankshaft position sensor signal is input to the ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met (1 trip detection logic):

(a) Engine speed is 1000 rpm or more.

(b) STA signal is off.

(c) 3 seconds or more have elapsed after STA signal is switched from on to off.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

No. 2 camshaft timing sprocket

·

ECM



Related Data List
DTC No. Data List
P0335
P0339
Engine Speed

HINT:

If DTC P0335 and/or P0339 is stored, the following symptoms may appear:

-

Difficulty starting

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power




WIRING DIAGRAM

A165739E17
0.552,1.781 2.219,1.958 1.667,0.177 10 false Camshaft Position Sensor 0.531,4.063 2.323,4.24 1.792,0.177 10 false Crankshaft Position Sensor 1.104,2.667 1.469,2.833 0.365,0.167 10 false NE+ 1.521,2.635 1.698,2.781 0.177,0.146 10 false 1 2.76,2.229 2.938,2.375 0.177,0.146 10 false * 0.344,4.469 1.104,4.635 0.76,0.167 10 false *: Shielded 3.5,0.25 3.677,0.396 0.177,0.146 10 false * 1.135,3.333 1.469,3.479 0.333,0.146 10 false NE- 5.49,2.667 5.844,2.844 0.354,0.177 10 false NE+ 5.177,2.667 5.479,2.854 0.302,0.188 10 false 78 5.51,3.375 5.896,3.552 0.385,0.177 10 false NE- 5.729,4.208 6.115,4.406 0.385,0.198 10 false ECM 5.167,3.365 5.427,3.51 0.26,0.146 10 false 77 5.51,0.667 5.844,0.813 0.333,0.146 10 false G+ 5.198,0.667 5.406,0.854 0.208,0.188 10 false 80 5.51,1.365 5.844,1.51 0.333,0.146 10 false G- 5.198,1.385 5.438,1.563 0.24,0.177 10 false 79 1.521,3.333 1.698,3.479 0.177,0.146 10 false 2 1.521,0.656 1.698,0.802 0.177,0.146 10 false 1 1.521,1.365 1.698,1.51 0.177,0.146 10 false 2 1.063,3.604 1.427,3.771 0.365,0.167 10 false GND 1.521,3.688 1.698,3.833 0.177,0.146 10 false 3 5.729,4.052 6.708,4.271 0.979,0.219 10 false C45*1, C46*2 0.531,3.906 0.823,4.083 0.292,0.177 10 false C65 0.552,1.615 0.865,1.792 0.313,0.177 10 false C66 3.542,4.146 4.302,4.313 0.76,0.167 10 false *1: for LHD 3.542,4.427 4.302,4.594 0.76,0.167 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).



HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

The Data List item Engine Speed is calculated from the output of the crankshaft position sensor.

·

A DTC is also stored when the ground of a shielded wire is faulty.



PROCEDURE

1.INSPECT CRANKSHAFT POSITION SENSOR

OK

2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

7.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C65-1 (NE+) - C45-78 (NE+) Always Below 1 Ω
C65-2 (NE-) - C45-77 (NE-) Always Below 1 Ω
C65-1 (NE+) or C45-78 (NE+) - Body ground Always 10 kΩ or higher
C65-2 (NE-) or C45-77 (NE-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C65-1 (NE+) - C46-78 (NE+) Always Below 1 Ω
C65-2 (NE-) - C46-77 (NE-) Always Below 1 Ω
C65-1 (NE+) or C46-78 (NE+) - Body ground Always 10 kΩ or higher
C65-2 (NE-) or C46-77 (NE-) - Body ground Always 10 kΩ or higher



d.

Reconnect the crankshaft position sensor connector.


e.

Reconnect the ECM connector.



OK

3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.
A208464E01
0.401,1.758 0.649,1.91 0.249,0.152 10 OK 2.664,1.768 2.912,1.92 0.249,0.152 10 NG

Check the sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE

NG

9.SECURELY REINSTALL SENSOR
4.CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
a.

Check the teeth of the sensor plate.

OK:

The sensor plate teeth do not have any cracks or deformation.




OK

5.INSPECT NO. 2 CAMSHAFT TIMING SPROCKET

NG

10.REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
5.INSPECT NO. 2 CAMSHAFT TIMING SPROCKET
a.

Check the condition of the timing sprocket.

OK:

Timing sprocket does not have any cracks or deformation.




OK

6.REPLACE ECM

NG

11.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
6.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE CRANKSHAFT POSITION SENSOR
a.


NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.SECURELY REINSTALL SENSOR

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
a.

Replace the No. 1 crankshaft position sensor plate (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE NO. 2 CAMSHAFT TIMING SPROCKET
a.

Replace the No. 2 camshaft timing sprocket (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine and run it at 1000 rpm or more for 5 seconds or more.


e.

Enter the following menus: Engine and ECT / Trouble Codes.


f.

Confirm that the DTC is not output again.



NEXT

END