Refer to DTC P0100 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>P0102).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| After the engine is completely warmed up, perform the following procedure 3 times: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more. | After the engine is completely warmed up, while the accelerator pedal is released for 7 seconds or more and the vehicle is decelerating, the intake air volume is higher or lower than the threshold* (EGR valve fully closed and throttle valve is fully open).
(2 trip detection logic) |
·
Mass air flow meter ·
Intake air temperature sensor (turbo) ·
Manifold absolute pressure sensor ·
No. 1 or No. 2 EGR valve assembly ·
ECM ·
Open or short in mass air flow meter circuit |
*: There is a threshold for a low airflow rate malfunction and high airflow rate malfunction. The threshold is different depending on the values of "Engine Speed", "MAP" and "Intake Air Temp (Turbo)".
Low airflow rate malfunction: For example, when the vehicle is decelerating, if "MAF" is 20 gm/sec or less, a low airflow malfunction is confirmed to be present (when "Engine Speed" is 1600 rpm, "MAP" is 110 kPa and "Intake Air Temp (Turbo)" is 35°C).
High airflow rate malfunction: For example, when the vehicle is decelerating, if "MAF" is 42 gm/sec or more, a high airflow malfunction is confirmed to be present (when "Engine Speed" is 1600 rpm, "MAP" is 110 kPa and "Intake Air Temp (Turbo)" is 35°C).
| DTC No. | Data List |
|---|---|
| P0101 | ·
MAF ·
MAP ·
Engine Speed ·
Intake Air Temp (Turbo) ·
Target EGR Valve Pos ·
Target EGR Valve Pos #2 ·
Actual EGR Valve Pos ·
Actual EGR Valve Pos #2 |
If DTC P0101 is stored, either of the following symptoms may appear:
As the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR.
Combustion noise worsens
As the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR:
Misfire
White smoke
Black smoke
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0101 and other DTCs are output | A |
| P0101 is output | B |
If codes other than P0101 are output, perform troubleshooting for those DTCs first.
B
A
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Engine and ECT / Trouble Codes.
Check the freeze frame data.
| Result | Proceed to |
|---|---|
·
Engine speed 1350 rpm or less ·
MAF 246.0 gm/sec or more |
A |
·
Engine speed 1350 rpm or more ·
MAF 0.03 gm/sec or less |
|
| Except above | B |
A
B
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / MAF and Engine speed.
Read the value.
| Engine speed | MAF |
|---|---|
| 0 rpm | 0.5 gm/sec or less |
| 550 to 650 rpm | 100 gm/sec or less |
| 3000 rpm | 1 gm/sec or more |
OK
NG
Replace the mass air flow meter (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER (w/o DPF)>REMOVAL).
If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0101.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P0101 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
B
A
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C45-119 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C45-94 (EVG) | Always | Below 1 Ω |
| C50-3 (VG) or C45-119 (VG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C46-119 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C46-94 (EVG) | Always | Below 1 Ω |
| C50-3 (VG) or C46-119 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / MAF and Engine speed.
Read the value.
| Engine speed | MAF |
|---|---|
| 0 rpm | 0.35 gm/sec or less |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / MAP and Atmospheric Pressure.
Compare the values when the ignition switch is ON.
Difference between "MAP" and "Atmosphere Pressure" is less than 8 kPa.
If "MAP" and "Atmosphere Pressure" have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.
Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather.
OK
NG
Check the air induction system for vacuum leakage (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leakage from air induction system.
Check for abnormal disconnection, pipe and hose squashing, and any damage in the intake system.
Using your hand, check whether the pipes and hoses in the intake system are securely connected.
Air leaks from the intake system can be checked by applying soapy water and revving the engine.
Check for any modifications in the intake system made by the user.
OK
NG
Connect the GTS to the DLC3.
Soak the engine for a long time.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).
Intake Air is the same as Intake Air Temp (Turbo).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Engine and ECT / Active Test / Control the EGR Step Position or Control the EGR Step Position #2.
While continuously changing the Active Test value to 0, 30, 60, 90, 60, 30 and 0%, check that Actual EGR Valve Pos or Actual EGR Valve Pos #2 smoothly changes to the set opening lift amount.
Value smoothly changes to within +/- 10% of set opening lift amount.
EGR valve closed: 0%.
EGR valve open: 95.2%.
Next, after the engine is warmed up, stop the engine and wait for 15 seconds. After that, start the engine again and idle it for 30 seconds. Then stop the engine and wait for 15 seconds. After starting the engine again, read the Data List values while idling.
Enter the following menus: Data List / EGR Close Lrn. Val. or EGR Close Lrn. Val. #2.
Read the values.
3.5 to 4.5 V
OK
NG
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C45-119 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C45-94 (EVG) | Always | Below 1 Ω |
| C50-3 (VG) or C45-119 (VG) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-3 (VG) - C46-119 (VG) | Always | Below 1 Ω |
| C50-2 (E2G) - C46-94 (EVG) | Always | Below 1 Ω |
| C50-3 (VG) or C46-119 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
OK
NG
Replace the mass air flow meter (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER (w/o DPF)>REMOVAL).
If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0101.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P0101 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
A
B
Inspect the intake air temperature sensor (turbo) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION).
OK
NG
Remove the No. 1 and No. 2 EGR valve assembly (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).
Visually check the EGR valve assembly for deposits.
If there are deposits, clean the EGR valve and EGR passage (intake/exhaust manifold, EGR cooler, EGR pipes, etc.).
When cleaning the EGR valve assembly, make sure the valve is completely closed.
When cleaning the EGR valve assembly, perform initialization procedure (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Do not forcibly open the valve, as it may be damaged or deformed.
When cleaning the EGR valve assembly, use a piece of cloth soaked with cleaning solvent. Spraying the solvent directly onto these parts or soaking the parts in the solvent may damage the parts.
Reinstall the EGR valve assembly (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE>INSTALLATION).
OK
NG
Replace the mass air flow meter (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>MASS AIR FLOW METER (w/ DPF)>REMOVAL).
If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the pending DTCs.
If no pending DTCs are output, proceed to the next step to check "All Readiness".
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0101.
Check the DTC judgment result.
| GTS Display | Result | Proceed to |
|---|---|---|
| Pending DTC | P0101 is output | B |
| All Readiness | NORMAL | A |
| ABNORMAL | B |
If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
A
B
Repair or replace the air induction system.
NEXT
Replace the No. 1 or No. 2 EGR valve assembly (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).
NEXT
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the manifold absolute pressure sensor.
NEXT
Replace the intake air temperature sensor (turbo) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Start the engine.
After the engine is completely warmed up, perform the following procedure 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
Stop the vehicle immediately after completing the above procedure.
Connect the GTS to the DLC3.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the pending DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0101.
Check the DTC judgment result.
If STATUS is INCOMPLETE or N/A, perform the following procedure again 3 times with the A/C off: from a vehicle speed of 60 km/h (37 mph), accelerate the vehicle to 80 km/h (50 mph), quickly release the accelerator pedal and do not depress it for 7 seconds or more.
NEXT