Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:
·

This is the repair procedure for the accelerator pedal position sensor.

·

This electrical throttle system does not use a throttle cable.

·

This accelerator pedal position sensor is a non-contact type.



The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator pedal position sensor.

In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.

A129363E09
0.781,2.75 0.26,1.542 0.26,1.542 0.313,1.542 false 0.792,3.063 0.271,4.271 0.271,4.271 0.333,4.271 false 0.917,2.271 1.281,1.531 false 1.281,4.313 0.917,3.573 false 5.594,1.396 5.906,1.573 false 6.052,1.813 6.375,1.99 false 2.406,0.198 4.094,0.552 1.688,0.354 10 false Accelerator Pedal Position Sensor Output Voltage (V) 0.219,0.74 1.469,1.135 1.25,0.396 10 false Accelerator Pedal Position Sensor 1.323,1.396 1.927,1.604 0.604,0.208 10 false Magnet 0.375,1.458 1.042,1.667 0.667,0.208 10 false IC No. 1 0.375,4.188 1.021,4.385 0.646,0.198 10 false IC No. 2 1.323,4.25 1.833,4.458 0.51,0.208 10 false Magnet 1.521,1.823 1.865,2.021 0.344,0.198 10 false VPA 1.521,2.167 1.885,2.365 0.365,0.198 10 false EPA 1.469,2.531 1.938,2.729 0.469,0.198 10 false VCPA 1.469,2.896 1.906,3.094 0.438,0.198 10 false VPA2 1.469,3.271 1.917,3.469 0.448,0.198 10 false EPA2 1.469,3.635 1.927,3.833 0.458,0.198 10 false VCP2 2.177,1.51 2.583,1.708 0.406,0.198 10 false ECM 3.927,1.125 4.063,1.323 0.135,0.198 10 false 5 3.375,1.573 4.031,1.771 0.656,0.198 10 false 3.7 to 5.0 3.375,1.906 4.031,2.115 0.656,0.208 10 false 2.9 to 4.2 3.396,2.5 4.052,2.698 0.656,0.198 10 false 1.4 to 1.8 3.385,2.854 4.063,3.063 0.677,0.208 10 false 0.6 to 1.0 4.021,3.49 4.135,3.688 0.115,0.198 10 false 0 4.49,3.458 5.583,3.656 1.094,0.198 10 false Usable Range 5.677,3.542 5.99,3.74 0.313,0.198 10 false 20.6 6.448,1.948 6.813,2.146 0.365,0.198 10 false VPA 5.146,1.302 5.604,1.5 0.458,0.198 10 false VPA2 4.365,3.823 6.719,4.031 2.354,0.208 10 false Accelerator Pedal Opening Angle (°) 0.26,4.875 2.625,5.073 2.365,0.198 10 false *1: Accelerator Pedal Fully Released 0.26,5.302 2.719,5.51 2.458,0.208 10 false *2: Accelerator Pedal Fully Depressed 4.427,0.573 4.615,0.771 0.188,0.198 10 false *1 5.76,0.573 5.948,0.771 0.188,0.198 10 false *2

P2120
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA is less than 0.4 V and VPA2 is more than 0.97 deg, or VPA is more than 4.8 V.
·

Accelerator pedal position sensor

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



P2122
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Condition (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA is less than 0.4 V.
(b) VPA2 is more than 0.97 deg.
·

Accelerator pedal position sensor

·

Open in VCPA circuit

·

VPA circuit open or ground short

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



P2123
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Condition (a) continues for 2.0 seconds (1 trip detection logic):
(a) VPA is more than 4.8 V.
·

Accelerator pedal position sensor

·

Open in EPA circuit

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



P2125
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Condition (a) continues for 0.5 seconds (1 trip detection logic):
(a) VPA2 is less than 1.2 V and VPA is more than 2.7 deg, or VPA2 is more than 4.8 V and VPA is more than 0.4 V but less than 3.45 V.
·

Accelerator pedal position sensor

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



P2127
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Condition (a) and (b) continue for 0.5 seconds (1 trip detection logic):
(a) VPA2 is less than 1.2 V.
(b) VPA2 is more than 2.7 deg.
·

Accelerator pedal position sensor

·

Open in VCP2 circuit

·

VPA2 circuit open or ground short

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



P2128
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic):
(a) VPA2 is more than 4.8 V.
(b) VPA is more than 0.4 V but less than 3.45 V.
·

Accelerator pedal position sensor

·

Open in EPA2 circuit

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



P2138
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON
·

Accelerator pedal fully closed for 3 seconds

·

Accelerator pedal open partway for 3 seconds

·

Accelerator pedal fully open for 3 seconds


Condition (a) or (b) continues for 2.0 seconds (1 trip detection logic):
(a) The difference between VPA and VPA2 is less than 0.02 V.
(b) VPA is less than 0.4 V and VPA2 is less than 1.2 V.
·

VPA and VPA2 circuits are short-circuited

·

Accelerator pedal position sensor

·

Accelerator pedal

·

Accelerator pedal rod (arm) deformed

·

ECM



Related Data List
DTC No. Data List
P2120
·

Accel Sens. No.1 Volt %

·

Accel Sens. No.2 Volt %

·

Accel Sensor Out No.1

·

Accel Sensor Out No.2


P2122
P2123
P2125
P2127
P2128
P2138

HINT:

When DTC P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 is stored, check the output voltage of the accelerator pedal position sensor by entering the following menus: Powertrain / Engine / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area Accelerator Pedal Position Expressed as Voltage Output
Accelerator Pedal Released Accelerator Pedal Depressed
Accel Sensor Out No.1 Accel Sensor Out No.2 Accel Sensor Out No.1 Accel Sensor Out No.2
VC circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
VPA circuit open or ground short 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 5.0 V
VPA2 circuit open or ground short 0.5 to 1.1 V 0 to 0.2 V 2.9 to 3.6 V 0 to 0.2 V
EPA circuit open 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V


WIRING DIAGRAM

A149601E49
0.281,3.198 2.438,3.406 2.156,0.208 10 false Accelerator Pedal Position Sensor 5.604,1.229 6.063,1.438 0.458,0.208 10 false VCPA 5.302,1.49 5.542,1.698 0.24,0.208 10 false 55 5.313,0.646 5.521,0.854 0.208,0.208 10 false 53 5.313,2.729 5.563,2.938 0.25,0.208 10 false 56 5.302,1.052 5.521,1.26 0.219,0.208 10 false 57 5.313,1.906 5.542,2.135 0.229,0.229 10 false 54 5.302,2.333 5.542,2.552 0.24,0.219 10 false 58 5.604,0.406 6,0.615 0.396,0.208 10 false VPA 5.604,0.792 6.052,1 0.448,0.208 10 false EPA 5.604,2.51 6.052,2.719 0.448,0.208 10 false VCP2 5.604,1.625 6.042,1.833 0.438,0.208 10 false VPA2 5.604,2.073 6.198,2.281 0.594,0.208 10 false EPA2 1.448,1.365 1.927,1.573 0.479,0.208 10 false VCPA 1.552,0.521 1.927,0.729 0.375,0.208 10 false VPA 1.542,0.948 1.917,1.156 0.375,0.208 10 false EPA 1.469,2.615 1.917,2.823 0.448,0.208 10 false VCP2 1.469,1.781 1.906,1.99 0.438,0.208 10 false VPA2 1.458,2.198 1.917,2.406 0.458,0.208 10 false EPA2 1.99,1.479 2.198,1.688 0.208,0.208 10 false 4 1.99,0.635 2.198,0.844 0.208,0.208 10 false 6 1.99,1.073 2.198,1.281 0.208,0.208 10 false 5 1.99,2.74 2.198,2.948 0.208,0.208 10 false 1 1.99,1.885 2.198,2.094 0.208,0.208 10 false 3 1.99,2.313 2.198,2.521 0.208,0.208 10 false 2 5.74,3.208 6.135,3.406 0.396,0.198 10 false ECM 5.729,3.042 6.677,3.229 0.948,0.188 10 false A38*1, A52*2 0.281,3.031 0.677,3.25 0.396,0.219 10 false A31 3.375,2.948 4.323,3.135 0.948,0.188 10 false *1: for LHD 3.385,3.271 4.333,3.458 0.948,0.188 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION)
a.
C129061E02
0.576,1.599 1.330,1.807 0.754,0.208 10 Depressed 0.971,0.06 2.301,0.266 1.330,0.205 10 Accelerator Pedal 1.969,1.599 2.633,1.811 0.664,0.212 10 Released

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.


d.

Read the values.

Standard:
Accelerator Pedal Accel Sens. No.1 Volt % Accel Sens. No.2 Volt %
Released 10 to 22% 24 to 40%
Depressed 52 to 90% 68 to 99%


Result
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

B

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)
a.

Disconnect the accelerator pedal position sensor connector.

A385267E01
1.74,0.938 2.156,1.198 0.417,0.26 4.583,0.802 5,1.063 0.417,0.26 5.292,0.792 5.708,1.052 0.417,0.26 1.198,1.969 1.656,1.75 true 1.156,1.458 1.76,1.698 true 1.469,1.208 1.885,1.688 true 2.01,1.708 2.375,1.208 true 2.125,1.698 2.635,1.448 true 2.24,1.729 2.698,1.844 true 4.365,1.115 5.01,1.906 true 4.792,2.24 5.094,1.906 true 4.938,2.375 5.156,1.906 true 5.448,2.448 5.229,1.917 true 5.802,1.344 5.313,1.917 true 5.646,2.25 5.375,1.906 true 0.729,0.135 3.115,0.51 2.385,0.375 10 false Front view of wire harness connector: (to Accelerator Pedal Position Sensor) 3.844,0.135 6.229,0.51 2.385,0.375 10 false Front view of wire harness connector: (to ECM) 1.823,0.99 2.167,1.188 0.344,0.198 10 false A31 0.75,1.917 1.188,2.115 0.438,0.198 10 false VCP2 0.719,1.354 1.156,1.552 0.438,0.198 10 false EPA2 1.042,1.021 1.479,1.219 0.438,0.198 10 false VPA2 2.396,1.021 2.833,1.219 0.438,0.198 10 false VCPA 2.677,1.344 3.115,1.542 0.438,0.198 10 false EPA 2.729,1.76 3.167,1.958 0.438,0.198 10 false VPA 3.75,0.927 4.427,1.125 0.677,0.198 10 false 53 (VPA) 4.094,2.167 4.823,2.365 0.729,0.198 10 false 54 (VPA2) 4.427,2.406 5.156,2.604 0.729,0.198 10 false 55 (VCPA) 5.219,2.479 5.948,2.677 0.729,0.198 10 false 56 (VCP2) 5.677,2.229 6.406,2.427 0.729,0.198 10 false 58 (EPA2) 5.833,1.229 6.563,1.427 0.729,0.198 10 false 57 (EPA) 4.667,0.854 5.01,1.052 0.344,0.198 10 false A38 5.375,0.844 5.719,1.042 0.344,0.198 10 false A52 5.031,0.719 5.271,0.917 0.24,0.198 10 false *1 5.729,0.698 5.969,0.896 0.24,0.198 10 false *2 0.198,2.406 1.219,2.615 1.021,0.208 10 false *1: for LHD 1.146,2.406 2.167,2.615 1.021,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) - A38-56 (VCP2) Always Below 1 Ω
A31-2 (EPA2) - A38-58 (EPA2) Always Below 1 Ω
A31-3 (VPA2) - A38-54 (VPA2) Always Below 1 Ω
A31-4 (VCPA) - A38-55 (VCPA) Always Below 1 Ω
A31-5 (EPA) - A38-57 (EPA) Always Below 1 Ω
A31-6 (VPA) - A38-53 (VPA) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) - A52-56 (VCP2) Always Below 1 Ω
A31-2 (EPA2) - A52-58 (EPA2) Always Below 1 Ω
A31-3 (VPA2) - A52-54 (VPA2) Always Below 1 Ω
A31-4 (VCPA) - A52-55 (VCPA) Always Below 1 Ω
A31-5 (EPA) - A52-57 (EPA) Always Below 1 Ω
A31-6 (VPA) - A52-53 (VPA) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) or A38-56 (VCP2) - Body ground Always 10 kΩ or higher
A31-2 (EPA2) or A38-58 (EPA2) - Body ground Always 10 kΩ or higher
A31-3 (VPA2) or A38-54 (VPA2) - Body ground Always 10 kΩ or higher
A31-4 (VCPA) or A38-55 (VCPA) - Body ground Always 10 kΩ or higher
A31-5 (EPA) or A38-57 (EPA) - Body ground Always 10 kΩ or higher
A31-6 (VPA) or A38-53 (VPA) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A31-1 (VCP2) or A52-56 (VCP2) - Body ground Always 10 kΩ or higher
A31-2 (EPA2) or A52-58 (EPA2) - Body ground Always 10 kΩ or higher
A31-3 (VPA2) or A52-54 (VPA2) - Body ground Always 10 kΩ or higher
A31-4 (VCPA) or A52-55 (VCPA) - Body ground Always 10 kΩ or higher
A31-5 (EPA) or A52-57 (EPA) - Body ground Always 10 kΩ or higher
A31-6 (VPA) or A52-53 (VPA) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS)
a.
U162826E01
0.292,0.107 2.726,0.459 2.434,0.352 10 Front view of wire harness connector: (to Accelerator Pedal Position Sensor) 1.778,2.518 2.178,2.686 0.400,0.167 10 VCPA 0.474,2.518 0.874,2.686 0.400,0.167 10 VCP2 2.427,2.518 2.749,2.686 0.323,0.167 10 EPA 1.134,2.518 1.544,2.686 0.409,0.167 10 EPA2 0.717,2.479 1.304,1.83 false 1.355,2.484 1.462,1.858 false 1.981,2.484 1.733,1.858 false 2.511,2.473 1.896,1.858 false 1.526,1.042 1.790,1.224 0.264,0.181 10 A31

Disconnect the accelerator pedal position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A31-4 (VCPA) - A31-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A31-1 (VCP2) - A31-2 (EPA2) Ignition switch ON 4.5 to 5.5 V




OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

6.REPLACE ECM
4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).



NEXT

5.CHECK IF OUTPUT DTC RECURS
5.CHECK IF OUTPUT DTC RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON.


e.

Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, then fully open it for 3 seconds.


f.

Read the DTCs.

Result
Result Proceed to
P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 are output again A
No output B



A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch off and leave the vehicle for 15 seconds.


e.

Turn the ignition switch to ON.


f.

Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, then fully open it for 3 seconds.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, idle the engine.




NEXT

END