Refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| After idling for 60 seconds, run engine at 2500 rpm for 30 seconds | The fuel pressure decreases greatly when the engine is running (1 trip detection logic). | ·
Fuel line between fuel supply pump and common rail ·
Fuel line between common rail and fuel injector ·
Fuel supply pump ·
Common rail (for Bank 2) (pressure limiter) ·
Fuel injector (P1238 set simultaneously) ·
Open or short in EDU circuit (P062D and/or P062E set simultaneously) ·
Open or short in fuel injector circuit (P062D, P062E and/or P1238 set simultaneously) ·
EDU (P062D and/or P062E set simultaneously) ·
Fuel line (air bleeding) ·
ECM |
| DTC No. | Data List |
|---|---|
| P0093 | ·
Fuel Press ·
Target Common Rail Pressure ·
Injection Pressure Correction ·
Target Pump SCV Current |
For more information on the common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).
If DTC P0093 is present, refer to the "Diagnostic Trouble Code (DTC) Table for Common Rail System" (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DIAGNOSTIC TROUBLE CODE CHART).
When DTC P0093 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine / Data List / Fuel Press.
| Engine Speed | Fuel Press |
|---|---|
| Idling | Approximately 27 to 37 MPa |
| 2500 rpm (No engine load) | Approximately 50 to 70 MPa |
When there is an operating problem with the fuel supply pump (Fuel Press is less than Target Common Rail Pressure), the values of Injection Pressure Correction and Target Pump SCV Current will increase.
This DTC indicates that fuel leaks exist in highly-pressurized areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when the fuel is injected.
In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump, common rail, fuel injectors, and piping. The ECM adjusts the suction control valve opening angle to obtain the desired fuel pressure.
If this DTC is stored, the ECM enters fail-safe mode. The fail-safe mode suspends both fuel injection and fuel supply pump operation, and then stops the engine. Before stopping the engine, the ECM permits the vehicle to be driven for 60 seconds. The fail-safe mode continues until the ignition switch is turned to off.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION ) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
After replacing the fuel injector, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
|---|---|
| P0093 is output | A |
| P0093 and other DTCs are output | B |
A
B
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DIAGNOSTIC TROUBLE CODE CHART)
By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak.
Visually check the fuel supply pump, fuel injector and fuel line located between the fuel supply pump and common rail for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail and the fuel injector.
No leakage.
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press and Target Common Rail Pressure.
When the Active Test is started, check that Fuel Press follows Target Common Rail Pressure and that the fuel pressure increases.
Fuel pressure reaches target pressure within 1 second.
OK
NG
Check the fuel receiver gauge. If the indicator is illuminated, add fuel.
Operate the hand pump of the fuel filter, and bleed air from the fuel line.
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Start the engine, and accelerate the engine at full throttle several times.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0093 is output | A |
| No DTC is output | B |
A
B
Start the engine, and allow the engine to idle for 20 seconds or more.
Stop the engine, and wait for 15 seconds or more.
Perform the procedures above 3 times or more in succession.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P0093 is output | A |
| No DTC is output | B |
If the MIL turns off, accelerate the engine at full throttle several times.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
After warming up the engine (engine coolant temperature is 75°C (167°F) or more), idle the engine (A/C off and electrical load off) for 1 minute or more.
Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Val #1 to #8.
Read the values.
Compensatory injection volume is between -3.0 mm3/st to 3.0 mm3/st.
If the fuel injector is malfunctioning, the compensatory injection volume remains at -5.0 mm3/st or 5.0 mm3/st.
The compensatory injection volume is usually between -3.0 mm3/st to 3.0 mm3/st.
Any cylinders that have a higher compensatory injection volume than shown above are considered to be faulty.
OK
NG
Replace the fuel supply pump (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Allow the engine to idle for 1 minute and then run it at 2500 rpm for 30 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P0093 is output | B |
A
B
NEXT
NEXT
Replace the fuel injector (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL INJECTOR (w/ DPF)>REMOVAL).
NEXT
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON and start the engine.
Allow the engine to idle for 1 minute and then run it at 2500 rpm for 30 seconds.
Confirm that the DTC is not output again.
Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P0093.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, maintain the engine at 2500 rpm for 30 seconds and then increase idling time.
NEXT