Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0088  Fuel Rail / System Pressure - Too High  


DESCRIPTION

Refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

P0088
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds The fuel pressure of common rail is too high
The fuel pressure exceeds 230 MPa (2345 kgf/cm2, 33358 psi) (1 trip detection logic).
·

Fuel supply pump (suction control valve)

·

Pressure limiter (common rail (for Bank 2))

·

Open or short in fuel supply pump (suction control valve) circuit

·

ECM



Related Data List
DTC No. Data List
P0088
·

Fuel Press

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

·

When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine / Data List / Fuel Press.

Reference
Engine Speed Fuel Press
Idling Approximately 27 to 37 MPa
2500 rpm (No engine load) Approximately 50 to 70 MPa

·

When there is an operating problem with the fuel supply pump (when Fuel Press is more than Target Common Rail Pressure due to a problem with the closing of the suction valve), the values of Injection Pressure Correction and Target Pump SCV Current decrease.



MONITOR DESCRIPTION

P0088 (Internal fuel pressure too high):

The ECM stores this DTC if the fuel pressure inside the common rail is more than 230 MPa (2345 kgf/cm2, 33350 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.


WIRING DIAGRAM

A184082E08
1.801,0.707 2.027,0.886 0.225,0.179 10 +B 2.087,0.707 2.281,0.886 0.194,0.179 10 1 1.669,1.384 2.011,1.563 0.342,0.179 10 PCV 5.35,0.707 5.622,0.886 0.273,0.179 10 106 5.357,1.384 5.622,1.563 0.266,0.179 10 105 5.733,1.286 6.144,1.465 0.412,0.179 10 PCV- 5.798,1.838 6.718,2.017 0.920,0.179 10 C45*1, C46*2 5.798,2.015 6.190,2.194 0.392,0.179 10 ECM 5.733,0.625 6.144,0.804 0.412,0.179 10 PCV+ 2.087,1.384 2.281,1.563 0.194,0.179 10 2 0.637,1.999 2.029,2.182 1.392,0.184 10 Suction Control Valve 3.776,1.832 4.103,1.999 0.327,0.166 10 zC1 0.637,1.813 0.965,1.979 0.327,0.166 10 z64 4.532,2.211 5.443,2.377 0.911,0.166 10 *1: for LHD 4.532,2.47 5.443,2.636 0.911,0.166 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector and then start the engine.

OK:

Engine does not start.




OK

2.READ VALUE USING INTELLIGENT TESTER

NG

6.REPLACE FUEL SUPPLY PUMP
2.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Target Pump SCV Current.


e.

Read the value.

Standard
Engine Speed Target Pump SCV Current
Idling 923 to 1123 mA
2500 rpm (No engine load) 1013 to 1212 mA



OK

3.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

6.REPLACE FUEL SUPPLY PUMP
3.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press, Target Common Rail Pressure.


e.

Check the difference in pressure between Fuel Press and Target Common Rail Pressure.

OK:

Difference in pressure between Fuel Press and Target Common Rail Pressure is within +/-5 MPa.




OK

4.REPLACE PRESSURE LIMITER (COMMON RAIL (for Bank 2))

NG

5.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE CONNECTOR - ECM)
4.REPLACE PRESSURE LIMITER (COMMON RAIL (for Bank 2))
a.

Replace the common rail (for Bank 2) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE CONNECTOR - ECM)
a.

Disconnect the suction control valve connector.

A385062E01
4.104,0.875 4.552,1.146 0.448,0.271 4.844,0.865 5.292,1.135 0.448,0.271 1.646,0.979 2.094,1.25 0.448,0.271 1.5,2.146 1.75,1.802 true 2.271,2.135 1.969,1.813 true 4.938,2.281 5.188,1.938 true 5.604,2.313 5.271,1.938 true 0.635,0.094 2.979,0.448 2.344,0.354 10 false Front view of wire harness connector: (to Suction Control Valve) 3.76,0.094 6.104,0.448 2.344,0.354 10 false Front view of wire harness connector: (to ECM) 1.74,1.031 2.135,1.24 0.396,0.208 10 false z64 4.188,0.927 4.583,1.135 0.396,0.208 10 false C45 4.938,0.917 5.333,1.125 0.396,0.208 10 false C46 4.583,0.729 4.844,0.927 0.26,0.198 10 false *1 5.313,0.74 5.573,0.938 0.26,0.198 10 false *2 1.323,2.188 1.719,2.396 0.396,0.208 10 false +B 2.219,2.156 2.615,2.365 0.396,0.208 10 false PCV 4.344,2.323 5.125,2.531 0.781,0.208 10 false 105 (PCV-) 5.365,2.333 6.208,2.542 0.844,0.208 10 false 106 (PCV+) 0.188,2.063 0.969,2.271 0.781,0.208 10 false *1: for LHD 0.188,2.385 0.969,2.594 0.781,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C45-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C45-106 (PCV+) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C46-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C46-106 (PCV+) Always Below 1 Ω


Standard Resistance (Check for short):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C45-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C45-106 (PCV+) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C46-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C46-106 (PCV+) - Body ground Always 10 kΩ or higher




OK

6.REPLACE FUEL SUPPLY PUMP

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.REPLACE FUEL SUPPLY PUMP
a.

Replace the fuel supply pump (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Display (DTC output) Proceed to
P0088 is output A
No DTC is output B



A

8.REPLACE ECM

B

END

8.REPLACE ECM

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P0088.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, race the engine to 2500 rpm repeatedly for 30 seconds and increase idling time.




NEXT

END