Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0627  Fuel Pump Control Circuit / Open  


DESCRIPTION

Refer to the System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

P0627
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 1 second Even though the CPU (command area inside ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic).
·

Open or short in suction control valve circuit

·

Suction control valve

·

ECM



Related Data List
DTC No. Data List
P0627 Fuel Press

HINT:
·

For more information on the fuel supply pump (suction control valve) and the common rail system, refer to the System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

·

When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Fuel Press.

Under a stable operating condition such as idling, Fuel Press is within +/-5 MPa of Target Common Rail Pressure.



WIRING DIAGRAM

A184082E09
1.801,0.694 2.027,0.873 0.225,0.179 10 +B 2.087,0.694 2.281,0.873 0.194,0.179 10 1 1.669,1.371 2.011,1.550 0.342,0.179 10 PCV 5.35,0.694 5.622,0.873 0.273,0.179 10 106 5.357,1.371 5.622,1.550 0.266,0.179 10 105 5.733,1.273 6.144,1.452 0.412,0.179 10 PCV- 5.798,1.825 6.718,2.004 0.920,0.179 10 C45*1, C46*2 5.798,2.002 6.190,2.181 0.392,0.179 10 ECM 5.733,0.612 6.144,0.791 0.412,0.179 10 PCV+ 2.087,1.371 2.281,1.550 0.194,0.179 10 2 0.661,2.056 2.053,2.239 1.392,0.184 10 Suction Control Valve 3.776,1.819 4.103,1.986 0.327,0.166 10 zC1 0.661,1.854 0.988,2.021 0.327,0.166 10 z64 4.531,2.05 5.451,2.229 0.920,0.179 10 *1: for LHD 4.531,2.323 5.451,2.502 0.920,0.179 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.
A164257E04
1.74,1.406 2.24,1.406 false 1.375,1.833 1.375,1.531 false 1.698,1.323 2.01,1.042 2.01,1.042 2.198,1.042 false 0.552,1.844 2.031,2.135 1.479,0.292 10 true Suction Control Valve 2.292,1.333 2.458,1.521 0.167,0.188 10 false 1 2.281,0.969 2.385,1.115 0.104,0.146 10 false 2 0.052,0.042 2.521,0.417 2.469,0.375 10 false Component without harness connected: (Fuel Supply Pump)

Disconnect the suction control valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 1.9 to 2.3 Ω




OK

2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)

NG

4.REPLACE FUEL SUPPLY PUMP
2.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.

A385062E01
4.104,0.875 4.552,1.146 0.448,0.271 4.844,0.865 5.292,1.135 0.448,0.271 1.646,0.979 2.094,1.25 0.448,0.271 1.5,2.146 1.75,1.802 true 2.271,2.135 1.969,1.813 true 4.938,2.281 5.188,1.938 true 5.604,2.313 5.271,1.938 true 0.635,0.094 2.979,0.448 2.344,0.354 10 false Front view of wire harness connector: (to Suction Control Valve) 3.76,0.094 6.104,0.448 2.344,0.354 10 false Front view of wire harness connector: (to ECM) 1.74,1.031 2.135,1.24 0.396,0.208 10 false z64 4.188,0.927 4.583,1.135 0.396,0.208 10 false C45 4.938,0.917 5.333,1.125 0.396,0.208 10 false C46 4.583,0.729 4.844,0.927 0.26,0.198 10 false *1 5.313,0.74 5.573,0.938 0.26,0.198 10 false *2 1.323,2.188 1.719,2.396 0.396,0.208 10 false +B 2.219,2.156 2.615,2.365 0.396,0.208 10 false PCV 4.344,2.323 5.125,2.531 0.781,0.208 10 false 105 (PCV-) 5.365,2.333 6.208,2.542 0.844,0.208 10 false 106 (PCV+) 0.188,2.063 0.969,2.271 0.781,0.208 10 false *1: for LHD 0.188,2.385 0.969,2.594 0.781,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C45-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C45-106 (PCV+) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C46-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C46-106 (PCV+) Always Below 1 Ω


Standard Resistance (Check for short):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C45-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C45-106 (PCV+) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C46-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C46-106 (PCV+) - Body ground Always 10 kΩ or higher




OK

3.CHECK WHETHER DTC OUTPUT RECURS

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3


b.

Turn the ignition switch to ON and turn the tester on.



d.

Start the engine and idle it for 1 second.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Read the DTCs.

Result
Result Proceed to
P0627 is output A
No DTC is output B



A

6.REPLACE ECM

B

END

4.REPLACE FUEL SUPPLY PUMP
a.

Replace the fuel supply pump (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine and idle it for 1 second.


e.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P0627.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase idling time.




NEXT

END