Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P1229  Fuel Pump System  


DESCRIPTION

Refer to the System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

P1229
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Idling for 60 seconds The actual fuel pressure exceeds the target fuel pressure by 40 MPa or more for 10 seconds (1 trip detection logic).
·

Short in fuel supply pump (suction control valve) circuit

·

Fuel supply pump (suction control valve)

·

Fuel pressure sensor (common rail (for Bank 1))

·

ECM



Related Data List
DTC No. Data List
P1229
·

Fuel Press

·

Target Common Rail Pressure

·

Injection Pressure Correction

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump (suction control valve) and common rail system, refer to the System Description (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>SYSTEM DESCRIPTION).

·

When DTC P1229 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine / Data List / Fuel Press, Target Common Rail Pressure.

Under a stable condition such as idling or running the engine at 2500 rpm without load, Fuel Press is within +/-5 MPa of Target Common Rail Pressure.

·

When there is an operating problem with the fuel supply pump (when Fuel Press is more than Target Common Rail Pressure due to a problem with the closing of the suction valve), the values of Injection Pressure Correction and Target Pump SCV Current decrease.



MONITOR DESCRIPTION

P1229 (Fuel over-feed):

The ECM stores this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.


WIRING DIAGRAM

A185918E04
1.787,4.312 2.012,4.491 0.225,0.179 10 +B 2.081,4.542 2.275,4.721 0.194,0.179 10 1 1.67,4.965 2.013,5.144 0.342,0.179 10 PCV 5.219,4.505 5.492,4.684 0.273,0.179 10 106 5.226,5.182 5.492,5.360 0.266,0.179 10 105 5.602,5.084 6.014,5.262 0.412,0.179 10 PCV- 5.667,5.635 6.587,5.813 0.920,0.179 10 C45*1, C46*2 5.667,5.812 6.059,5.991 0.392,0.179 10 ECM 5.602,4.423 6.014,4.602 0.412,0.179 10 PCV+ 2.081,5.219 2.275,5.398 0.194,0.179 10 2 0.334,5.735 1.726,5.918 1.392,0.184 10 Suction Control Valve 3.636,5.721 3.963,5.887 0.327,0.166 10 zC1 5.289,1.85 5.513,2.029 0.224,0.179 10 69 5.307,2.611 5.518,2.789 0.210,0.179 10 75 5.581,2.38 5.798,2.558 0.217,0.179 10 E2 5.581,1.635 5.993,1.814 0.412,0.179 10 PCR1 2,1.63 2.253,1.809 0.253,0.179 10 PR 2.327,1.855 2.521,2.034 0.194,0.179 10 2 2.025,2.384 2.249,2.563 0.224,0.179 10 E2 2.327,2.631 2.521,2.809 0.194,0.179 10 1 0.78,3.236 2.165,3.420 1.385,0.184 10 Fuel Pressure Sensor 2.002,0.895 2.246,1.074 0.244,0.179 10 VG 2.327,1.117 2.521,1.296 0.194,0.179 10 3 0.764,3.008 1.085,3.187 0.321,0.179 10 C82 5.298,1.123 5.501,1.302 0.203,0.179 10 70 5.574,0.886 5.986,1.065 0.412,0.179 10 VCM 0.484,6.134 1.242,6.318 0.758,0.184 10 *1: for LHD 0.484,6.428 1.242,6.612 0.758,0.184 10 *2: for RHD 0.334,5.539 0.661,5.705 0.327,0.166 10 z64

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector and then check if the engine starts.

OK:

Engine does not start.




OK

2.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)

NG

6.REPLACE FUEL SUPPLY PUMP
2.READ VALUE USING INTELLIGENT TESTER (TARGET PUMP SCV CURRENT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Target Pump SCV Current.


e.

Read the value.

OK:
Engine Speed Target Pump SCV Current
Idling 923 to 1123 mA
2500 rpm (No engine load) 1013 to 1212 mA




OK

3.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)

NG

4.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE CONNECTOR - ECM)
3.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


d.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Fuel Press is within +/-5 MPa of Target Common Rail Pressure when engine is idling and running at 2500 rpm without load.




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

4.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE CONNECTOR - ECM)
4.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE CONNECTOR - ECM)
a.

Disconnect the suction control valve connector.

A385062E01
4.104,0.875 4.552,1.146 0.448,0.271 4.844,0.865 5.292,1.135 0.448,0.271 1.646,0.979 2.094,1.25 0.448,0.271 1.5,2.146 1.75,1.802 true 2.271,2.135 1.969,1.813 true 4.938,2.281 5.188,1.938 true 5.604,2.313 5.271,1.938 true 0.635,0.094 2.979,0.448 2.344,0.354 10 false Front view of wire harness connector: (to Suction Control Valve) 3.76,0.094 6.104,0.448 2.344,0.354 10 false Front view of wire harness connector: (to ECM) 1.74,1.031 2.135,1.24 0.396,0.208 10 false z64 4.188,0.927 4.583,1.135 0.396,0.208 10 false C45 4.938,0.917 5.333,1.125 0.396,0.208 10 false C46 4.583,0.729 4.844,0.927 0.26,0.198 10 false *1 5.313,0.74 5.573,0.938 0.26,0.198 10 false *2 1.323,2.188 1.719,2.396 0.396,0.208 10 false +B 2.219,2.156 2.615,2.365 0.396,0.208 10 false PCV 4.344,2.323 5.125,2.531 0.781,0.208 10 false 105 (PCV-) 5.365,2.333 6.208,2.542 0.844,0.208 10 false 106 (PCV+) 0.188,2.063 0.969,2.271 0.781,0.208 10 false *1: for LHD 0.188,2.385 0.969,2.594 0.781,0.208 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C45-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C45-106 (PCV+) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) - C46-105 (PCV-) Always Below 1 Ω
z64-1 (+B) - C46-106 (PCV+) Always Below 1 Ω


Standard Resistance (Check for short):
for LHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C45-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C45-106 (PCV+) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z64-2 (PCV) or C46-105 (PCV-) - Body ground Always 10 kΩ or higher
z64-1 (+B) or C46-106 (PCV+) - Body ground Always 10 kΩ or higher




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Start the engine.


e.

Idle the engine for 60 seconds.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
P1229 is output A
No DTC is output B



A

6.REPLACE FUEL SUPPLY PUMP

B

END

6.REPLACE FUEL SUPPLY PUMP
a.

Replace the fuel supply pump (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL).



NEXT

7.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
7.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.


d.

Check that the internal fuel pressure of the common rail is within the specification below.

OK:

Fuel Press is within +/-5 MPa of Target Common Rail Pressure when engine is idling and running at 2500 rpm without load.




OK

8.CHECK WHETHER DTC OUTPUT RECURS

NG

10.REPLACE COMMON RAIL (for Bank 1) (FUEL PRESSURE SENSOR)
8.CHECK WHETHER DTC OUTPUT RECURS

b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Start the engine.


e.

Idle the engine for 60 seconds.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result
Result Proceed to
P1229 is output A
No DTC is output B



A

9.REPLACE ECM

B

END

9.REPLACE ECM

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPLACE COMMON RAIL (for Bank 1) (FUEL PRESSURE SENSOR)
a.

Replace common rail (for Bank 1) (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).



NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Idle the engine for 60 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P1229.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase idling time.




NEXT

END