Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0180  Fuel Temperature Sensor "A" Circuit  P0182  Fuel Temperature Sensor "A" Circuit Low Input  P0183  Fuel Temperature Sensor "A" Circuit High Input  


DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (See Fig. 1).

The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.

Resistor R and the fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the fuel supply pump and determines if there are errors.

A385085E01
1.417,2.042 1.688,1.625 1.688,1.625 1.823,1.625 false 0.198,0.094 1.427,0.292 1.229,0.198 10 false (Fig. 1) 0.177,0.469 1.406,0.667 1.229,0.198 10 false Resistance kΩ 1.26,4.115 2.698,4.323 1.438,0.208 10 false Temperature °C (°F) 1.875,1.521 2.719,1.719 0.844,0.198 10 false Acceptable

P0180
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open or short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open or short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM



P0182
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Short in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Short in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM



P0183
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 0.5 seconds Open in the fuel temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Open in fuel temperature sensor circuit

·

Fuel temperature sensor

·

ECM



Related Data List
DTC No. Data List
P0180 Fuel Temp
P0182
P0183

HINT:
·

If DTC P0180, P0182 and/or P0183 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

Lack of power




WIRING DIAGRAM

A184084E09
2.063,1.031 2.396,1.198 0.333,0.167 10 false THF 2.469,1.24 2.646,1.417 0.177,0.177 10 false 2 2.115,1.625 2.375,1.802 0.26,0.177 10 false E2 5.563,1.031 5.875,1.198 0.313,0.167 10 false THF 6.25,0.542 6.563,0.708 0.313,0.167 10 false 5 V 5.563,1.635 5.802,1.802 0.24,0.167 10 false E2 6.177,0.865 6.333,1.031 0.156,0.167 10 false R 2.469,1.854 2.646,2.031 0.177,0.177 10 false 1 5.167,1.26 5.5,1.448 0.333,0.188 10 false 116 5.729,2.667 6.667,2.844 0.938,0.177 10 false C45*1, C46*2 5.729,2.844 6.146,3.021 0.417,0.177 10 false ECM 5.26,1.865 5.49,2.052 0.229,0.188 10 false 75 0.698,2.417 2.365,2.604 1.667,0.188 10 false Fuel Temperature Sensor 0.438,3 1.385,3.188 0.948,0.188 10 false *1: for LHD 0.438,3.292 1.385,3.479 0.948,0.188 10 false *2: for RHD 3.875,2.646 4.198,2.802 0.323,0.156 10 false zC1 0.677,2.25 1,2.406 0.323,0.156 10 false z65

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


HINT:
·

If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine / Data List / Fuel Temp.


d.

Read the value.

OK:

Same value as the actual fuel temperature.


Result
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or more B
OK (Same as actual fuel temperature) C

HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or more.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.

Disconnect the fuel temperature sensor connector.

A385126E01
5.01,0.781 5.458,1.01 0.448,0.229 4.813,1.958 5.146,1.604 true 5.635,1.969 5.313,1.615 true 0.427,1.771 2.125,1.969 1.698,0.198 10 false Fuel Temperature Sensor 2.698,1.885 3.135,2.083 0.438,0.198 10 false ECM 2.542,1.156 2.979,1.354 0.438,0.198 10 false THF 2.573,1.552 3.01,1.75 0.438,0.198 10 false E2 4.167,0.094 6.5,0.469 2.333,0.375 10 false Front view of wire harness connector: (to Fuel Temperature Sensor) 5.104,0.833 5.49,1.031 0.385,0.198 10 false z65 4.667,1.99 5.104,2.188 0.438,0.198 10 false E2 5.583,2 6.021,2.198 0.438,0.198 10 false THF


b.

Connect terminals 2 (THF) and 1 (E2) of the fuel temperature sensor connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Data List / Fuel Temp.


f.

Read the value.

OK:

140°C (284°F) or higher




OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.

A385130E01
1.646,0.958 2.073,1.208 0.427,0.25 4.073,0.885 4.5,1.135 0.427,0.25 4.844,0.875 5.271,1.125 0.427,0.25 1.344,1.396 1.75,1.656 true 2.021,1.677 2.406,1.333 true 3.906,2.281 4.292,1.938 true 4.865,2.281 4.646,1.792 true 0.729,0.156 3.052,0.542 2.323,0.385 10 false Front view of wire harness connector: (to Fuel Temperature Sensor) 3.708,0.156 6.031,0.542 2.323,0.385 10 false Front view of wire harness connector: (to ECM) 1.729,1 2.052,1.188 0.323,0.188 10 false z65 4.146,0.938 4.469,1.125 0.323,0.188 10 false C45 4.938,0.917 5.26,1.104 0.323,0.188 10 false C46 4.531,0.813 4.771,1 0.24,0.188 10 false *1 5.302,0.813 5.542,1 0.24,0.188 10 false *2 1.083,1.229 1.406,1.417 0.323,0.188 10 false E2 2.438,1.198 2.76,1.385 0.323,0.188 10 false THF 3.51,2.313 4.26,2.479 0.75,0.167 10 false 116 (THF) 4.615,2.313 5.365,2.479 0.75,0.167 10 false 75 (E2) 0.271,1.969 1.073,2.167 0.802,0.198 10 false *1: for LHD 0.271,2.302 1.073,2.5 0.802,0.198 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
z65-2 (THF) - C45-116 (THF) Always Below 1 Ω
z65-1 (E2) - C45-75 (E2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
z65-2 (THF) - C46-116 (THF) Always Below 1 Ω
z65-1 (E2) - C46-75 (E2) Always Below 1 Ω




OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A166688E06
0.111,2.323 1.718,2.488 1.607,0.165 10 Fuel Temperature Sensor 2.629,2.323 3.000,2.485 0.371,0.163 10 ECM 2.416,1.404 2.781,1.566 0.365,0.162 10 THF 2.416,1.87 2.781,2.032 0.365,0.162 10 E2

Disconnect the fuel temperature sensor connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Temp.


e.

Read the value.

OK:

-40°C (-40°F)




OK

7.REPLACE FUEL TEMPERATURE SENSOR

NG

8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
7.REPLACE FUEL TEMPERATURE SENSOR
a.

Replace the fuel temperature sensor (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL TEMPERATURE SENSOR>REMOVAL).



NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CHECK HARNESS AND CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.

A385130E02
1.646,0.958 2.073,1.208 0.427,0.25 4.073,0.885 4.5,1.135 0.427,0.25 4.844,0.875 5.271,1.125 0.427,0.25 2.021,1.677 2.406,1.333 true 3.906,2.281 4.292,1.938 true 4.865,2.281 4.646,1.792 true 0.729,0.156 3.052,0.542 2.323,0.385 10 false Front view of wire harness connector: (to Fuel Temperature Sensor) 3.708,0.156 6.031,0.542 2.323,0.385 10 false Front view of wire harness connector: (to ECM) 1.729,1 2.052,1.188 0.323,0.188 10 false z65 4.146,0.938 4.469,1.125 0.323,0.188 10 false C45 4.938,0.917 5.26,1.104 0.323,0.188 10 false C46 4.531,0.813 4.771,1 0.24,0.188 10 false *1 5.302,0.813 5.542,1 0.24,0.188 10 false *2 2.438,1.198 2.76,1.385 0.323,0.188 10 false THF 3.51,2.313 4.26,2.479 0.75,0.167 10 false 116 (THF) 4.615,2.313 5.365,2.479 0.75,0.167 10 false 75 (E2) 0.271,1.969 1.073,2.167 0.802,0.198 10 false *1: for LHD 0.271,2.302 1.073,2.5 0.802,0.198 10 false *2: for RHD


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
z65-2 (THF) or C45-116 (THF) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
z65-2 (THF) or C46-116 (THF) - Body ground Always 10 kΩ or higher




OK

9.REPLACE ECM

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.REPLACE ECM

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END