Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A384783E01
1.323,1.083 2.667,1.281 1.344,0.198 10 false from EFI MAIN Fuse 1.583,1.448 2.635,1.646 1.052,0.198 10 false from EFI Relay 4.365,1.125 6.167,1.344 1.802,0.219 10 false 5 V Constant Voltage Circuit 5.375,1.917 6.406,2.156 1.031,0.24 10 false Microprocessor 5.021,3.344 5.448,3.531 0.427,0.188 10 false ECM 4.063,3.125 4.24,3.292 0.177,0.167 10 false R 3.177,2.292 3.49,2.469 0.313,0.177 10 false VC 3.031,1.344 3.344,1.521 0.313,0.177 10 false +B 2.865,0.979 3.344,1.167 0.479,0.188 10 false BATT 0.188,2 2.646,2.51 2.458,0.51 10 false to Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.177,2.948 2.667,3.375 2.49,0.427 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc.

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

U162943E01
2.226,0.746 2.488,0.908 0.262,0.163 10 VC 2.569,0.83 2.704,0.992 0.135,0.163 10 3 2.242,1.53 2.504,1.693 0.262,0.163 10 E2 2.569,1.614 2.704,1.777 0.135,0.163 10 2 2.086,1.131 2.487,1.294 0.401,0.163 10 EGLS 2.569,1.215 2.704,1.378 0.135,0.163 10 4 0.658,1.975 0.993,2.139 0.335,0.165 10 C87 0.658,2.116 2.766,2.487 2.108,0.371 10 No. 1 EGR Valve Position Sensor (No. 1 EGR Valve) 2.226,3.274 2.488,3.437 0.262,0.163 10 VC 2.569,3.359 2.704,3.521 0.135,0.163 10 3 2.226,4.059 2.488,4.222 0.262,0.163 10 E2 2.569,4.143 2.704,4.306 0.135,0.163 10 2 2.086,3.66 2.487,3.823 0.401,0.163 10 EGS2 2.569,3.744 2.704,3.907 0.135,0.163 10 4 0.658,4.503 0.993,4.668 0.335,0.165 10 C88 0.658,4.644 2.755,5.016 2.096,0.371 10 No. 2 EGR Valve Position Sensor (No. 2 EGR Valve) 2.071,6.763 2.487,6.926 0.416,0.163 10 VCP2 2.569,6.847 2.704,7.010 0.135,0.163 10 1 2.071,6.336 2.487,6.499 0.416,0.163 10 VCPA 2.569,6.42 2.704,6.583 0.135,0.163 10 4 2.071,5.935 2.487,6.098 0.416,0.163 10 VPA2 2.569,6.023 2.704,6.186 0.135,0.163 10 3 2.071,7.548 2.487,7.710 0.416,0.163 10 EPA2 2.569,7.632 2.704,7.795 0.135,0.163 10 2 2.169,7.148 2.488,7.311 0.318,0.163 10 EPA 2.569,7.232 2.704,7.395 0.135,0.163 10 5 2.169,5.52 2.488,5.683 0.318,0.163 10 VPA 5.048,6.739 5.464,6.902 0.416,0.163 10 VCP2 5.048,6.336 5.464,6.499 0.416,0.163 10 VCPA 5.048,5.939 5.464,6.102 0.416,0.163 10 VPA2 5.048,7.536 5.464,7.699 0.416,0.163 10 EPA2 5.048,7.136 5.367,7.299 0.318,0.163 10 EPA 5.048,5.528 5.367,5.691 0.318,0.163 10 VPA 4.682,5.528 5.001,5.691 0.318,0.163 10 A52 4.682,5.927 5.001,6.090 0.318,0.163 10 A52 5.048,3.669 5.464,3.832 0.416,0.163 10 EGS2 4.682,3.658 5.001,3.820 0.318,0.163 10 C46 5.048,1.561 5.464,1.723 0.416,0.163 10 EEGL 4.682,1.549 5.001,1.712 0.318,0.163 10 C46 5.048,1.154 5.464,1.317 0.416,0.163 10 EGLS 4.682,1.143 5.001,1.306 0.318,0.163 10 C46 5.048,0.755 5.464,0.918 0.416,0.163 10 VCEG 4.682,0.743 5.001,0.906 0.318,0.163 10 C46 4.682,6.334 5.001,6.496 0.318,0.163 10 A52 4.682,6.732 5.001,6.895 0.318,0.163 10 A52 4.682,7.138 5.001,7.301 0.318,0.163 10 A52 4.682,7.537 5.001,7.699 0.318,0.163 10 A52 2.569,5.604 2.704,5.767 0.135,0.163 10 6 0.658,7.992 0.993,8.157 0.335,0.165 10 A31 0.658,8.133 2.961,8.504 2.302,0.371 10 Accelerator Pedal Position Sensor (Accelerator Pedal) 4.346,5.528 4.664,5.691 0.318,0.163 10 A38 4.31,5.345 4.626,5.508 0.316,0.163 10 53*1 4.346,5.927 4.664,6.090 0.318,0.163 10 A38 4.31,5.744 4.626,5.907 0.316,0.163 10 54*1 4.346,3.658 4.664,3.820 0.318,0.163 10 C45 4.324,3.475 4.628,3.637 0.304,0.163 10 88*1 4.346,1.549 4.664,1.712 0.318,0.163 10 C45 4.324,1.366 4.642,1.529 0.318,0.163 10 87*1 4.346,1.143 4.664,1.306 0.318,0.163 10 C45 4.324,0.96 4.637,1.123 0.314,0.163 10 89*1 4.346,0.743 4.664,0.906 0.318,0.163 10 C45 4.324,0.56 4.633,0.723 0.309,0.163 10 90*1 4.346,6.334 4.664,6.496 0.318,0.163 10 A38 4.31,6.151 4.626,6.313 0.316,0.163 10 55*1 4.346,6.732 4.664,6.895 0.318,0.163 10 A38 4.31,6.549 4.626,6.712 0.316,0.163 10 56*1 4.346,7.138 4.664,7.301 0.318,0.163 10 A38 4.31,6.955 4.626,7.118 0.316,0.163 10 57*1 4.346,7.537 4.664,7.699 0.318,0.163 10 A38 4.31,7.354 4.626,7.516 0.316,0.163 10 58*1 4.66,5.345 4.976,5.508 0.316,0.163 10 53*2 4.66,5.744 4.976,5.907 0.316,0.163 10 54*2 4.66,6.151 4.976,6.313 0.316,0.163 10 55*2 4.66,6.549 4.976,6.712 0.316,0.163 10 56*2 4.66,6.955 4.976,7.118 0.316,0.163 10 57*2 4.66,7.354 4.976,7.516 0.316,0.163 10 58*2 4.66,3.475 4.964,3.637 0.304,0.163 10 88*2 4.66,1.366 4.978,1.529 0.318,0.163 10 87*2 4.66,0.96 4.973,1.123 0.314,0.163 10 89*2 4.66,0.56 4.969,0.723 0.309,0.163 10 90*2 3.347,8.134 4.117,8.296 0.770,0.163 10 *1: for LHD 3.347,8.431 4.117,8.593 0.770,0.163 10 *2: for RHD 5.42,8.438 5.801,8.601 0.381,0.163 10 ECM

U162944E01
2.218,0.627 2.480,0.790 0.262,0.163 10 VC 2.561,0.711 2.696,0.874 0.135,0.163 10 1 2.234,1.412 2.496,1.575 0.262,0.163 10 E2 2.561,1.496 2.696,1.659 0.135,0.163 10 2 2.157,1.012 2.480,1.175 0.322,0.163 10 VTA 2.561,1.096 2.696,1.259 0.135,0.163 10 3 0.853,1.852 1.188,2.017 0.335,0.165 10 C83 0.853,1.997 3.135,2.368 2.282,0.371 10 Throttle Position Sensor (for Bank 1) (Diesel Throttle Body) 2.218,3.017 2.480,3.180 0.262,0.163 10 VC 2.561,3.101 2.696,3.264 0.135,0.163 10 1 2.218,3.802 2.480,3.964 0.262,0.163 10 E2 2.561,3.886 2.696,4.048 0.135,0.163 10 2 2.076,3.402 2.479,3.565 0.403,0.163 10 VTA2 2.561,3.486 2.696,3.649 0.135,0.163 10 3 0.853,4.238 1.188,4.403 0.335,0.165 10 C84 0.853,4.383 3.156,4.754 2.302,0.371 10 Throttle Position Sensor (for Bank 2) (Diesel Throttle Body) 0.853,6.588 1.188,6.752 0.335,0.165 10 C82 0.853,6.733 2.555,7.104 1.702,0.371 10 Fuel Pressure Sensor (Common Rail [for Bank 1]) 2.242,7.765 2.481,7.928 0.239,0.163 10 VC 2.561,7.849 2.696,8.012 0.135,0.163 10 3 2.244,6.186 2.481,6.349 0.236,0.163 10 E2 2.561,6.27 2.696,6.433 0.135,0.163 10 1 2.237,5.785 2.480,5.947 0.243,0.163 10 PR 2.561,5.873 2.696,6.035 0.135,0.163 10 2 2.335,8.55 2.481,8.713 0.146,0.163 10 E 2.561,8.634 2.696,8.797 0.135,0.163 10 1 2.186,8.151 2.480,8.314 0.294,0.163 10 PIM 2.561,8.235 2.696,8.398 0.135,0.163 10 2 2.244,5.37 2.481,5.533 0.236,0.163 10 VG 5.041,6.178 5.294,6.341 0.254,0.163 10 E2 5.041,5.781 5.456,5.943 0.416,0.163 10 PCR1 5.041,5.37 5.436,5.533 0.395,0.163 10 VCM 4.674,5.37 4.993,5.533 0.318,0.163 10 C46 4.674,5.769 4.993,5.932 0.318,0.163 10 C46 5.041,8.176 5.456,8.339 0.416,0.163 10 PIM 5.405,8.914 5.820,9.077 0.416,0.163 10 ECM 5.041,7.766 5.496,7.928 0.456,0.163 10 VCPM 4.671,7.766 4.989,7.928 0.318,0.163 10 C46 4.671,8.165 4.989,8.328 0.318,0.163 10 C46 5.041,3.424 5.456,3.586 0.416,0.163 10 VLU2 4.667,3.416 4.985,3.579 0.318,0.163 10 C46 5.041,1.442 5.456,1.605 0.416,0.163 10 EVLU 4.659,1.427 4.977,1.589 0.318,0.163 10 C46 5.041,1.036 5.456,1.199 0.416,0.163 10 VLU 4.659,1.02 4.977,1.183 0.318,0.163 10 C46 5.041,0.636 5.456,0.799 0.416,0.163 10 VCVL 4.659,0.621 4.977,0.784 0.318,0.163 10 C46 4.674,6.175 4.993,6.338 0.318,0.163 10 C46 4.338,5.37 4.657,5.533 0.318,0.163 10 C45 4.306,5.187 4.631,5.350 0.325,0.163 10 70*1 4.338,5.769 4.657,5.932 0.318,0.163 10 C45 4.306,5.586 4.631,5.749 0.325,0.163 10 69*1 4.334,7.766 4.653,7.928 0.318,0.163 10 C45 4.306,7.583 4.648,7.745 0.342,0.163 10 66*1 4.334,8.165 4.653,8.328 0.318,0.163 10 C45 4.185,7.982 4.577,8.145 0.393,0.163 10 114*1 4.33,3.416 4.649,3.579 0.318,0.163 10 C45 4.185,3.229 4.587,3.392 0.402,0.163 10 103*1 4.322,1.427 4.641,1.589 0.318,0.163 10 C45 4.306,1.248 4.631,1.410 0.325,0.163 10 92*1 4.322,1.02 4.641,1.183 0.318,0.163 10 C45 4.306,0.841 4.631,1.004 0.325,0.163 10 93*1 4.322,0.621 4.641,0.784 0.318,0.163 10 C45 4.306,0.442 4.631,0.605 0.325,0.163 10 91*1 4.338,6.175 4.657,6.338 0.318,0.163 10 C45 4.306,5.992 4.631,6.155 0.325,0.163 10 75*1 4.656,5.187 4.981,5.350 0.325,0.163 10 70*2 4.656,5.586 4.981,5.749 0.325,0.163 10 69*2 4.656,7.583 4.998,7.745 0.342,0.163 10 66*2 4.591,7.982 4.984,8.145 0.393,0.163 10 114*2 4.586,3.229 4.988,3.392 0.402,0.163 10 103*2 4.656,1.248 4.981,1.410 0.325,0.163 10 92*2 4.656,0.841 4.981,1.004 0.325,0.163 10 93*2 4.656,0.442 4.981,0.605 0.325,0.163 10 91*2 4.656,5.992 4.981,6.155 0.325,0.163 10 75*2 2.561,5.454 2.696,5.617 0.135,0.163 10 3 0.853,8.994 1.188,9.159 0.335,0.165 10 C80 0.853,9.135 3.089,9.334 2.236,0.199 10 Manifold Absolute Pressure Sensor 3.75,9.46 4.518,9.623 0.768,0.163 10 *2: for RHD 3.743,9.138 4.511,9.301 0.768,0.163 10 *1: for LHD

CAUTION / NOTICE / HINT

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B



B

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM

A

END

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and tester on.


c.

Check the communication between the tester and ECM.

Result
Result Proceed to
Communication is possible A
Communication is not possible B



B

3.CHECK MIL (THROTTLE POSITION SENSOR (for Bank 1))

A

3.CHECK MIL (THROTTLE POSITION SENSOR (for Bank 1))
a.

Disconnect the C83 throttle position sensor (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the C83 throttle position sensor (for Bank 1) connector.



B

4.CHECK MIL (THROTTLE POSITION SENSOR (for Bank 2))

A

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

4.CHECK MIL (THROTTLE POSITION SENSOR (for Bank 2))
a.

Disconnect the C84 throttle position sensor (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the C84 throttle position sensor (for Bank 2) connector.



B

5.CHECK MIL (NO. 1 EGR VALVE POSITION SENSOR)

A

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

5.CHECK MIL (NO. 1 EGR VALVE POSITION SENSOR)
HINT:

For vehicles without EGR valve, perform troubleshooting from the next step.


a.

Disconnect the C87 No. 1 EGR valve connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the C87 No. 1 EGR valve connector.



B

6.CHECK MIL (NO. 2 EGR VALVE POSITION SENSOR)

A

REPLACE NO. 1 EGR VALVE ASSEMBLY

6.CHECK MIL (NO. 2 EGR VALVE POSITION SENSOR)
HINT:

For vehicles without EGR valve, perform troubleshooting from the next step.


a.

Disconnect the C88 No. 2 EGR valve connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the C88 No. 2 EGR valve connector.



B

7.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)

A

REPLACE NO. 2 EGR VALVE ASSEMBLY

7.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the A31 accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the A31 accelerator pedal position sensor connector.



B

8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

8.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the C80 manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the C80 manifold absolute pressure sensor connector.



B

9.CHECK MIL (FUEL PRESSURE SENSOR)

A

9.CHECK MIL (FUEL PRESSURE SENSOR)
a.

Disconnect the C82 fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
MIL illuminates A
MIL does not illuminate B


d.

Reconnect the C82 fuel pressure sensor connector.



B

10.CHECK HARNESS AND CONNECTOR

A

REPLACE COMMON RAIL (for Bank 1)

10.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle position sensor (for Bank 1) connector.


b.

Disconnect the throttle position sensor (for Bank 2) connector.


c.

Disconnect the No. 1 EGR valve connector.


d.

Disconnect the No. 2 EGR valve connector.


e.

Disconnect the accelerator pedal position sensor connector.


f.

Disconnect the manifold absolute pressure sensor connector.


g.

Disconnect the fuel pressure sensor connector.


h.

Disconnect the ECM connectors.

A384779E03
1.438,0.76 1.854,1.01 0.417,0.25 2.24,0.76 2.656,1.01 0.417,0.25 4.74,0.708 5.156,0.958 0.417,0.25 5.552,0.708 5.969,0.958 0.417,0.25 5.542,1.823 5.365,2.25 true 1.021,1.24 1.396,1.708 true 1.479,1.802 1.323,2.271 true 1.542,1.792 1.875,2.167 true 1.688,1.719 2.656,2.219 true 5.594,1.823 5.885,2.25 true 0.313,0.104 2.615,0.458 2.302,0.354 10 false Front view of wire harness connector: (to ECM) 1.51,0.802 1.833,0.99 0.323,0.188 10 false C45 2.323,0.813 2.646,1 0.323,0.188 10 false C46 1.896,0.698 2.125,0.896 0.229,0.198 10 false *1 2.719,0.698 2.948,0.896 0.229,0.198 10 false *2 2.708,2.198 3.531,2.406 0.823,0.208 10 false 70 (VCM) 5.792,2.292 6.594,2.531 0.802,0.24 10 false 56 (VCP2) 4.823,0.75 5.146,0.938 0.323,0.188 10 false A38 5.198,0.625 5.427,0.823 0.229,0.198 10 false *1 5.635,0.75 5.958,0.938 0.323,0.188 10 false A52 6.021,0.646 6.25,0.844 0.229,0.198 10 false *2 0.115,2.063 0.958,2.271 0.844,0.208 10 false *1: for LHD 0.115,2.396 0.958,2.604 0.844,0.208 10 false *2: for RHD 0.313,1.021 1.094,1.229 0.781,0.208 10 false 66 (VCPM) 0.979,2.323 1.802,2.521 0.823,0.198 10 false 90 (VCEG) 1.708,2.177 2.302,2.375 0.594,0.198 10 false 91 (VC) 4.844,2.281 5.646,2.521 0.802,0.24 10 false 55 (VCPA)


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C45-90 (VCEG) - Body ground Always 10 kΩ or higher
C45-91 (VCVL) - Body ground Always 10 kΩ or higher
C45-70 (VCM) - Body ground Always 10 kΩ or higher
C45-66 (VCPM) - Body ground Always 10 kΩ or higher
A38-55 (VCPA) - Body ground Always 10 kΩ or higher
A38-56 (VCP2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-90 (VCEG) - Body ground Always 10 kΩ or higher
C46-91 (VCVL) - Body ground Always 10 kΩ or higher
C46-70 (VCM) - Body ground Always 10 kΩ or higher
C46-66 (VCPM) - Body ground Always 10 kΩ or higher
A52-55 (VCPA) - Body ground Always 10 kΩ or higher
A52-56 (VCP2) - Body ground Always 10 kΩ or higher



j.

Reconnect the throttle position sensor (for Bank 1) connector.


k.

Reconnect the throttle position sensor (for Bank 2) connector.


l.

Reconnect the No. 1 EGR valve connector.


m.

Reconnect the No. 2 EGR valve connector.


n.

Reconnect the accelerator pedal position sensor connector.


o.

Reconnect the manifold absolute pressure sensor connector.


p.

Reconnect the fuel pressure sensor connector.


q.

Reconnect the ECM connectors.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR