Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A182518E01
5.923,2.402 6.783,2.559 0.861,0.157 10 A38*1, A52*2 1,2.528 1.865,2.685 0.864,0.157 10 *1: for LHD 1,2.8 1.865,2.957 0.864,0.157 10 *2: for RHD 6.193,2.586 6.589,2.742 0.397,0.156 10 ECM 6.03,0.998 6.244,1.154 0.214,0.156 10 W 5.764,1.202 5.957,1.357 0.193,0.156 10 24 4.947,1.119 5.174,1.275 0.226,0.156 10 E8 4.936,0.927 5.129,1.083 0.193,0.156 10 12 2.746,1.101 2.972,1.257 0.226,0.156 10 E7 2.734,0.909 2.927,1.065 0.193,0.156 10 18 3.709,1.278 4.005,1.441 0.296,0.163 10 MIL 4.508,1.229 4.846,1.392 0.338,0.163 10 CHK 3.033,1.229 3.329,1.392 0.296,0.163 10 IG+ 1.993,0.935 2.345,1.098 0.352,0.163 10 MET 3.38,2.084 4.627,2.247 1.247,0.163 10 Combination Meter 1.958,1.249 2.076,1.412 0.118,0.163 10 1 0.466,1.096 1.442,1.266 0.977,0.170 10 from IG2 relay 2.266,1.249 2.384,1.412 0.118,0.163 10 2

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Condition Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Check if DTCs have been stored (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>DTC CHECK / CLEAR). If DTCs are present, write them down.



e.

Check that the MIL turns off.

Standard:

MIL turns off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
U163236E01
0.261,0.096 2.593,0.442 2.332,0.346 10 Front view of wire harness connector: (to ECM) 1.145,0.901 1.449,1.064 0.304,0.163 10 A38 1.522,0.713 1.720,0.876 0.198,0.163 10 *1 0.26,2.575 1.016,2.738 0.756,0.163 10 *1: for LHD 0.26,2.873 1.016,3.035 0.756,0.163 10 *2: for RHD 2.004,0.901 2.308,1.064 0.304,0.163 10 A52 2.381,0.713 2.579,0.876 0.198,0.163 10 *2 2.667,2.004 3.157,2.188 0.490,0.185 10 24 (W) 1.783,1.728 2.625,2.074 false

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
U163714E02
1.844,3.521 2.76,3.948 false 1.219,1.615 0.563,1.813 false 0.219,0.052 2.51,0.417 2.292,0.365 10 false Rear view of wire harness connector: (to Combination Meter) 2.469,1.51 2.719,1.677 0.25,0.167 10 false E8 0.188,2.115 2.49,2.469 2.302,0.354 10 true Front view of wire harness connector: (to ECM) 1.333,2.76 1.604,2.927 0.271,0.167 10 false A38 1.615,2.625 1.771,2.781 0.156,0.156 10 false *1 0.073,4.052 0.823,4.208 0.75,0.156 10 false *1: for LHD 0.073,4.313 0.823,4.469 0.75,0.156 10 false *2: for RHD 1.99,2.76 2.281,2.927 0.292,0.167 10 false A52 2.271,2.625 2.427,2.781 0.156,0.156 10 false *2 2.802,3.865 3.292,4.042 0.49,0.177 10 false 24 (W) 0.417,1.833 0.771,1.99 0.354,0.156 10 false CHK

a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
E8-12 (CHK) - A38-24 (W) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
E8-12 (CHK) - A52-24 (W) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
E8-12 (CHK) or A38-24 (W) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E8-12 (CHK) or A52-24 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter connector.

Result
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C



C

REPAIR OR REPLACE HARNESS OR CONNECTOR

A

REPLACE COMBINATION METER ASSEMBLY (w/ Multi-information Display)

B

REPLACE COMBINATION METER ASSEMBLY (w/o Multi-information Display)

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

See the combination meter troubleshooting procedure (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>PROBLEM SYMPTOMS TABLE).

Result
Result Proceed to
NG A
OK (w/ Multi-information Display) B
OK (w/o Multi-information Display) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

B

REPLACE COMBINATION METER ASSEMBLY (w/ Multi-information Display)

C

REPLACE COMBINATION METER ASSEMBLY (w/o Multi-information Display)