Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P0046  Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance  P0047  Turbocharger/Supercharger Boost Control "A" Circuit Low  P0048  Turbocharger/Supercharger Boost Control "A" Circuit High  P004B  Turbocharger/Supercharger Boost Control Solenoid "B" Circuit Range/Performance  P004C  Turbocharger/Supercharger Boost Control Solenoid "B" Circuit Low  P004D  Turbocharger/Supercharger Boost Control Solenoid "B" Circuit High  


DESCRIPTION

These DTCs indicates that the DC motor of the turbocharger is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets the criteria, the ECM sets a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust emissions in order to control the turbo pressure. The ECM varies the duty-cycle of the DC motor in accordance with the driving condition.

If the nozzle vane is stuck closed (DC motor stuck off), the drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), the drivability may deteriorate at intermediate throttle or the engine power may be insufficient.

A325132E03
0.885,6.135 1.323,6.292 0.438,0.156 10 false ECM 4.385,3.042 7.063,3.24 2.677,0.198 10 false Nozzle Vane Position Sensor (for Bank 1) 2.396,6.271 3.604,6.479 1.208,0.208 10 false Turbo Motor Driver 5.083,0.979 6.646,1.188 1.563,0.208 10 false DC Motor (for Bank 1) 4.406,6.229 7.083,6.427 2.677,0.198 10 false Nozzle Vane Position Sensor (for Bank 2) 5.073,4.094 6.854,4.302 1.781,0.208 10 false DC Motor (for Bank 2) 1.208,0.896 1.656,1.063 0.448,0.167 10 false VNTO 1.188,4.042 1.635,4.208 0.448,0.167 10 false VNO2 1.219,1.25 1.604,1.406 0.385,0.156 10 false VNTI 3.167,4.531 3.563,4.698 0.396,0.167 10 false VTA2 3.313,0.375 3.573,0.542 0.26,0.167 10 false M+ 2.51,0.896 2.958,1.073 0.448,0.177 10 false VNTO 2.51,1.25 2.906,1.427 0.396,0.177 10 false VNTI 2.51,4.396 2.885,4.573 0.375,0.177 10 false VNI2 1.24,4.396 1.604,4.573 0.365,0.177 10 false VNI2 2.51,4.042 2.958,4.208 0.448,0.167 10 false VNO2 3.313,0.635 3.573,0.802 0.26,0.167 10 false M- 5.198,0.385 5.51,0.573 0.313,0.188 10 false M+ 5.198,0.656 5.458,0.823 0.26,0.167 10 false M- 5.198,3.5 5.531,3.667 0.333,0.167 10 false M2+ 5.208,3.771 5.552,3.938 0.344,0.167 10 false M2- 3.208,3.51 3.594,3.688 0.385,0.177 10 false M2+ 3.219,3.792 3.583,3.948 0.365,0.156 10 false M2- 3.167,4.802 3.552,4.969 0.385,0.167 10 false E2S2 5.198,4.844 6.073,5.01 0.875,0.167 10 false E2S2 3.146,5.073 3.604,5.24 0.458,0.167 10 false VCS2 5.198,5.104 6.167,5.271 0.969,0.167 10 false VCS2 3.208,1.438 3.688,1.646 0.479,0.208 10 false VTA 5.208,1.427 5.927,1.635 0.719,0.208 10 false VTA 3.229,1.667 3.729,1.833 0.5,0.167 10 false E2S 5.208,1.656 5.958,1.823 0.75,0.167 10 false E2S 3.208,1.927 3.76,2.094 0.552,0.167 10 false VCS 5.208,1.917 6.042,2.083 0.833,0.167 10 false VCS 5.198,4.583 5.948,4.75 0.75,0.167 10 false VTA2 5.208,2.177 5.927,2.385 0.719,0.208 10 false VTA1 5.219,2.438 5.969,2.604 0.75,0.167 10 false VNE2 5.208,2.698 6.042,2.865 0.833,0.167 10 false VNVC 5.198,5.615 6.073,5.781 0.875,0.167 10 false VE2 5.198,5.865 6.167,6.031 0.969,0.167 10 false VNC2 5.198,5.344 5.948,5.51 0.75,0.167 10 false VTI2 3.219,5.333 3.615,5.5 0.396,0.167 10 false VTI2 3.24,5.604 3.625,5.771 0.385,0.167 10 false VE2 3.125,5.833 3.583,6 0.458,0.167 10 false VNC2 3.188,2.156 3.667,2.365 0.479,0.208 10 false VTAI 3.156,2.417 3.656,2.583 0.5,0.167 10 false VNE2 3.115,2.698 3.667,2.865 0.552,0.167 10 false VNVC

P0046, P004B
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds Either of the following conditions are met when the motor is driving (1 trip detection logic):
·

DC motor duty ratio is +/-100% for 1.3 seconds or more.

·

DC motor current is 2.2 A or more for 5 seconds or more.


·

Open or short in DC motor (turbocharger sub-assembly) circuit

·

Turbo motor driver

·

DC motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



P0047, P004C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second Both of following conditions are met for 1 second or more when the motor is driving (1 trip detection logic):
·

DC motor duty ratio is 100%.

·

DC motor current is 0.5 A or less.


·

Open in DC motor (turbocharger sub-assembly) circuit

·

Turbo motor driver

·

DC Motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



P0048, P004D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second DC motor current is 6.5 A or more for 0.5 seconds or more when the motor is operating (1 trip detection logic).
·

Short in DC motor (turbocharger sub-assembly) circuit

·

Turbo motor driver

·

DC Motor (turbocharger sub-assembly)

·

Turbocharger nozzle vane is stuck or movement is irregular



HINT:

If DTC P0046, P0047, P0048, P004B, P004C and/or P004D is stored, the following symptoms may appear.

Stuck closed malfunction:

-

Vehicle surge when driving with full load


Stuck open malfunction:

-

Lack of power

-

Vehicle surge or hesitation under light or medium load

-

White smoke




WIRING DIAGRAM

A325134E01
5.182,1.177 5.435,1.347 0.254,0.170 10 3 5.112,0.822 5.396,0.992 0.284,0.170 10 10 5.112,2.931 5.411,3.101 0.299,0.170 10 19 5.112,3.307 5.407,3.477 0.295,0.170 10 18 1.924,1.177 2.085,1.347 0.161,0.170 10 2 1.924,0.822 2.168,0.992 0.244,0.170 10 1 1.621,0.71 1.859,0.880 0.237,0.170 10 M- 1.621,1.088 1.859,1.258 0.237,0.170 10 M+ 1.924,3.314 2.085,3.484 0.161,0.170 10 2 1.924,2.959 2.168,3.129 0.244,0.170 10 1 1.565,2.847 1.867,3.017 0.302,0.170 10 M2- 1.565,3.225 1.858,3.395 0.293,0.170 10 M2+ 5.39,2.833 5.692,3.003 0.302,0.170 10 M2- 5.39,3.197 5.683,3.367 0.293,0.170 10 M2+ 5.345,3.949 6.575,4.130 1.230,0.181 10 Turbo Motor Driver 5.39,0.71 5.627,0.880 0.237,0.170 10 M- 5.39,1.088 5.627,1.258 0.237,0.170 10 M+ 0.188,1.767 0.834,1.937 0.647,0.170 10 DC Motor 0.188,1.938 2.853,2.108 2.665,0.170 10 (Turbocharger sub-assembly) (for Bank 1) 0.188,3.871 0.834,4.041 0.647,0.170 10 DC Motor 0.188,4.047 2.853,4.217 2.665,0.170 10 (Turbocharger sub-assembly) (for Bank 2) 0.18,1.565 0.503,1.721 0.323,0.156 10 C90 0.176,3.68 0.498,3.836 0.323,0.156 10 z67 5.345,3.715 5.668,3.871 0.323,0.156 10 A48

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR) (for Bank 1 or Bank 2)
a.
A182376E01
0.247,0.096 2.744,0.420 2.497,0.324 10 Component without harness connected: (DC Motor)

Disconnect the DC motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Bank 1
Tester Connection Condition Specified Condition
1 (M-) - 2 (M+) Always 1 to 100 Ω


Standard Resistance:
for Bank 2
Tester Connection Condition Specified Condition
1 (M2-) - 2 (M2+) Always 1 to 100 Ω




OK

2.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

NG

6.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2)
2.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)
a.

Disconnect the DC motor (for Bank 1) connector.


b.

Disconnect the DC motor (for Bank 2) connector.


c.

Disconnect the turbo motor driver connector.

U163763E02
2,1.833 2.177,2.365 false 2.115,1.833 2.594,2.406 false 5.292,1.667 4.99,1.99 false 5.542,1.656 5.802,1.969 false 2.094,1.615 2.99,0.917 false 1.083,2.396 2,1.542 false 4.375,0.063 6.688,0.427 2.313,0.365 10 false Front view of wire harness connector: (to DC Motor (for Bank 1)) 1.167,0.052 3.5,0.406 2.333,0.354 10 false Front view of wire harness connector: (to Turbo Motor Driver) 3.542,2 4.323,2.177 0.781,0.177 10 false *1: Bank 1 3.031,0.781 3.323,1 0.292,0.219 10 false M- 2.604,2.385 2.917,2.583 0.313,0.198 10 false M2- 0.969,2.417 1.229,2.615 0.26,0.198 10 false M+ 2.125,2.385 2.448,2.583 0.323,0.198 10 false M2+ 4.885,2.031 5.281,2.229 0.396,0.198 10 false M-*1 5.74,2.01 6.208,2.219 0.469,0.208 10 false M+*1 1.979,0.76 2.292,0.958 0.313,0.198 10 false A48 4.969,1 5.281,1.198 0.313,0.198 10 false C90 5.573,1 5.885,1.198 0.313,0.198 10 false z67 5.281,0.792 5.479,0.99 0.198,0.198 10 false *1 5.917,0.781 6.115,0.979 0.198,0.198 10 false *2 3.542,2.302 4.323,2.479 0.781,0.177 10 false *2: Bank 2 4.885,2.198 5.375,2.406 0.49,0.208 10 false M2-*2 5.74,2.188 6.24,2.385 0.5,0.198 10 false M2+*2


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Bank 1
Tester Connection Condition Specified Condition
C90-1 (M-) - A48-10 (M-) Always Below 1 Ω
C90-2 (M+) - A48-3 (M+) Always Below 1 Ω

for Bank 2
Tester Connection Condition Specified Condition
z67-1 (M2-) - A48-19 (M2-) Always Below 1 Ω
z67-2 (M2+) - A48-18 (M2+) Always Below 1 Ω


Standard Resistance (Check for Short):
for Bank 1
Tester Connection Condition Specified Condition
C90-1 (M-) or A48-10 (M-) - Body ground Always 10 kΩ or higher
C90-2 (M+) or A48-3 (M+) - Body ground Always 10 kΩ or higher

for Bank 2
Tester Connection Condition Specified Condition
z67-1 (M2-) or A48-19 (M2-) - Body ground Always 10 kΩ or higher
z67-2 (M2+) or A48-18 (M2+) - Body ground Always 10 kΩ or higher




OK

3.INSPECT TURBOCHARGER SUB - ASSEMBLY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.INSPECT TURBOCHARGER SUB - ASSEMBLY
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm up.


d.

Move the shift lever to 3rd and accelerate the vehicle with the accelerator fully open.


e.

Stop the vehicle.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
DTC P0046, P0047, P0048, P004B, P004C and/or P004D are output A
No DTC output B


HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

"Target Booster Pressure" and "MAP" in the snapshot can be used to check the operation of the turbocharger. If "MAP" does not follow "Target Booster Pressure", the turbocharger nozzle vane may be stuck or the movement may be irregular.

·

When the engine speed is 2500 to 3000 rpm with the accelerator pedal fully depressed, "MAP" is within +/- 10 kPa* of "Target Booster Pressure" (not immediately after beginning of acceleration).

·

* If the turbocharger pressure does not reach a specified value, it cannot be determined whether the system is normal by checking whether "MAP" is within +/-10 kPa of "Target Booster Pressure".



U163764E02
3.792,1.646 3.99,1.156 false 4.219,1.771 4.5,1.552 false 4.094,2.208 4.229,2.292 false 3.792,3.844 3.854,4.083 false 2.302,3.365 2.531,3.135 false 6.167,2.615 6.219,2.479 false 2.552,3.083 3.292,3.26 0.74,0.177 8 true Shift Position 3.688,4.104 4.458,4.292 0.771,0.188 8 true Engine Speed 4.26,2.229 4.531,2.365 0.271,0.135 8 false MAP 4.521,1.469 5.802,1.625 1.281,0.156 8 true Target Booster Pressure 4.01,1.115 4.844,1.26 0.833,0.146 8 true VNT Command 2.729,1.094 3.167,1.219 0.438,0.125 8 false 2693ms 3.594,0.094 4.5,0.271 0.906,0.177 8 false Normal Condition 6.208,2.313 7,2.469 0.792,0.156 8 true Vehicle speed

HINT:

Compare "MAP" with "Target Booster Pressure" at the point indicated by the arrow (↑) in the illustration.




B

4.INSPECT TURBO MOTOR DRIVER

A

6.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2)
4.INSPECT TURBO MOTOR DRIVER
a.

Connect the intelligent tester to the DLC3.



c.

Turn the engine switch off.


d.

Remove the rear fender splash shield sub-assembly RH.


e.

Remove the front fender liner LH.


f.

Disconnect the turbo motor driver connector.


g.

Reconnect the turbo motor driver connector.


h.

Turn the engine switch on (IG) and turn the tester on.


i.

After starting the engine, idle it for 5 seconds.


j.

Enter the following menus: Powertrain / Engine / DTC.


k.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
DTC is output A
DTC is not output B




A

5.REPLACE TURBO MOTOR DRIVER

B

END

5.REPLACE TURBO MOTOR DRIVER
a.

Replace the turbo motor driver (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>TURBO MOTOR DRIVER>REMOVAL).

NOTICE:

Make sure that foreign matter does not enter the connector(s) when replacing parts.




NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2)
a.

Replace the turbocharger sub-assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 5 seconds or more.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END