Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P00AF  Turbocharger/Supercharger Boost Control "A" Module Performance  P00B0  Turbocharger/Supercharger Boost Control "B" Module Performance  


DESCRIPTION

The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, turbo motor driver and ECM.

The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure. When the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.

The turbocharger actuator, which consists of the DC motor and the nozzle vane position sensor, is built on the turbocharger sub-assembly, and activates the nozzle vane. The nozzle vane position sensor detects the opening angle of the nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position signal from the nozzle vane position sensor. Based on these signals, the turbo motor driver operates the DC motor and adjusts the nozzle vane opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM.

The ECM sends a target nozzle vane position signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.

A182385E04
1.971,4.951 2.405,5.107 0.434,0.156 10 ECM 0.052,0.677 1.429,0.860 1.377,0.184 10 Ignition Switch Signal 0.486,1.431 1.457,1.597 0.971,0.165 10 Engine Speed 0.118,2.157 1.432,2.330 1.313,0.172 10 Accelerator Position 0.388,2.932 1.424,3.097 1.036,0.165 10 Turbo Pressure 0.091,3.674 1.479,3.857 1.387,0.184 10 Barometric Pressure 0.1,4.334 1.443,4.721 1.343,0.387 10 Engine Coolant Temperature Sensor 2.643,1.717 3.611,2.220 0.969,0.503 10 Vane Nozzle Opening Angle Signal 4.902,4.622 5.907,4.994 1.005,0.371 10 Nozzle Vane Position Signal 6.025,4.757 7.093,5.095 1.068,0.338 10 Nozzle Vane Position Sensor 2.708,3.073 3.568,3.479 0.860,0.405 10 Motor Status Signal 3.494,5.006 4.705,5.167 1.211,0.161 10 Turbo Motor Driver 4.531,0.549 4.835,0.715 0.304,0.165 10 M+ 4.531,1.224 4.835,1.389 0.304,0.165 10 M- 4.933,3.009 5.763,3.202 0.830,0.193 10 VCS, VNVC 4.933,4.305 5.741,4.498 0.808,0.193 10 VTA1, VTA2 4.933,3.668 5.732,3.861 0.799,0.193 10 E2S, VNE2 6.179,1.756 6.821,1.903 0.642,0.147 10 DC Motor 4.879,1.459 5.984,1.800 1.105,0.341 10 DC Motor Activation Signal

P00AF
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 5 seconds When a communication error occurs between the turbo motor driver and ECM (1 trip detection logic).
·

Turbo motor driver

·

Open or short in turbo motor driver circuit

·

Turbo motor driver ground problem

·

ECM



P00B0
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
After idling for 5 seconds When a communication error occurs between the turbo motor driver and ECM (1 trip detection logic).
·

Turbo motor driver

·

Open or short in turbo motor driver circuit

·

Turbo motor driver ground problem

·

ECM



WIRING DIAGRAM

A322142E02
0.365,0.552 1.313,0.729 0.948,0.177 10 false from EFI relay 0.448,1.927 1.281,2.292 0.833,0.365 10 false from EFI MAIN 2 relay 2.281,0.552 2.552,0.75 0.271,0.198 10 false +B 2.281,2.01 2.646,2.208 0.365,0.198 10 false +B2 2.281,2.583 2.74,2.781 0.458,0.198 10 false GND2 2.948,0.552 3.396,0.75 0.448,0.198 10 false VNTO 5.667,2.125 5.906,2.323 0.24,0.198 10 false 47 5.667,2.688 5.906,2.885 0.24,0.198 10 false 48 5.667,1.25 5.906,1.448 0.24,0.198 10 false 50 5.667,0.677 5.906,0.875 0.24,0.198 10 false 49 2.969,2.021 3.417,2.219 0.448,0.198 10 false VNO2 3.021,2.615 3.417,2.813 0.396,0.198 10 false VNI2 3.49,0.667 3.667,0.865 0.177,0.198 10 false 5 3.49,1.25 3.667,1.448 0.177,0.198 10 false 4 3.469,2.125 3.813,2.323 0.344,0.198 10 false 20 3.469,2.688 3.813,2.885 0.344,0.198 10 false 11 2.063,0.677 2.24,0.875 0.177,0.198 10 false 1 2.083,1.24 2.26,1.438 0.177,0.198 10 false 2 2.01,2.115 2.24,2.313 0.229,0.198 10 false 16 1.99,2.688 2.229,2.885 0.24,0.198 10 false 17 3.021,1.146 3.396,1.344 0.375,0.198 10 false VNTI 5.938,0.552 6.385,0.75 0.448,0.198 10 false VNTO 5.938,2.021 6.385,2.219 0.448,0.198 10 false VNO2 5.938,2.583 6.302,2.781 0.365,0.198 10 false VNI2 5.938,1.135 6.313,1.333 0.375,0.198 10 false VNTI 2.219,3.25 3.438,3.469 1.219,0.219 10 false Turbo Motor Driver 5.823,3.135 6.729,3.302 0.906,0.167 10 false C45*1, C46*2 5.823,3.313 6.208,3.479 0.385,0.167 10 false ECM 2.281,1.125 2.646,1.323 0.365,0.198 10 false GND 0.167,3.042 0.979,3.208 0.813,0.167 10 false *1: for LHD 0.167,3.313 0.979,3.479 0.813,0.167 10 false *2: for RHD 2.219,3.094 2.583,3.292 0.365,0.198 10 false A48

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Excessive electrical noise, such as from wireless radios or electrical modifications, may cause a DTC to be stored.



NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).


PROCEDURE

1.INSPECT TURBO MOTOR DRIVER (POWER SOURCE CIRCUIT)
a.
U163760E01
1.528,1.091 1.830,1.256 0.302,0.165 10 A48 0.328,0.065 2.668,0.415 2.341,0.350 10 Front view of wire harness connector: (to Turbo Motor Driver) 1.119,2.278 0.815,3.112 false 1.363,2.277 1.667,3.112 false 0.597,3.112 0.897,3.277 0.300,0.165 10 +B2 1.451,3.112 1.892,3.277 0.440,0.165 10 GND2 0.214,3.112 0.460,3.277 0.246,0.165 10 +B 2.07,3.112 2.436,3.277 0.367,0.165 10 GND 1.123,2.106 0.428,3.112 false 1.368,2.114 2.17,3.112 false

Disconnect the turbo motor driver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-1 (+B) - A48-2 (GND) Engine switch on (IG) 11 to 14 V
A48-16 (+B2) - A48-17 (GND2) Engine switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-2 (GND) - Body ground Always Below 1 Ω
A48-17 (GND2) - Body ground Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM)
a.

Disconnect the turbo motor driver connector.


b.

Disconnect the ECM connector.

U163761E01
4.439,0.052 6.817,0.402 2.378,0.350 10 Front view of wire harness connector: (to Turbo Motor Driver) 0.991,0.052 3.369,0.403 2.378,0.351 10 Front view of wire harness connector: (to ECM) 4.469,2.321 4.951,2.477 0.482,0.156 10 VNTI 5.027,2.321 5.509,2.477 0.482,0.156 10 VNI2 6.099,2.321 6.685,2.477 0.586,0.156 10 VNTO 5.562,2.321 6.009,2.477 0.448,0.156 10 VNO2 5.489,1.746 5.202,2.321 false 5.545,1.617 6.231,2.308 false 1.497,0.918 1.805,1.074 0.308,0.156 10 C45 2.124,0.926 2.433,1.082 0.309,0.156 10 C46 1.862,0.824 2.051,0.990 0.189,0.165 10 *1 2.444,0.824 2.634,0.990 0.189,0.165 10 *2 2.558,2.394 3.346,2.549 0.788,0.156 10 50 (VNTI) 1.008,2.394 1.686,2.549 0.678,0.156 10 48 (VNI2) 1.708,2.394 2.590,2.549 0.883,0.156 10 49 (VNTO) 0.239,2.394 0.992,2.549 0.753,0.156 10 47 (VNO2) 3.501,2.046 4.370,2.221 0.869,0.176 10 *1: for LHD 3.501,2.377 4.370,2.552 0.869,0.176 10 *2: for RHD 1.099,1.579 0.782,2.364 false 1.17,1.583 1.349,2.38 false 1.316,1.579 2.568,2.38 false 1.239,1.579 1.902,2.38 false 5.294,0.848 5.602,1.004 0.308,0.156 10 A48 5.537,1.867 5.727,2.301 false 5.429,1.617 4.793,2.316 false


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LHD
Tester Connection Condition Specified Condition
C45-49 (VNTO) - A48-5 (VNTO) Always Below 1 Ω
C45-50 (VNTI) - A48-4 (VNTI) Always Below 1 Ω
C45-47 (VNO2) - A48-20 (VNO2) Always Below 1 Ω
C45-48 (VNI2) - A48-11 (VNI2) Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C46-49 (VNTO) - A48-5 (VNTO) Always Below 1 Ω
C46-50 (VNTI) - A48-4 (VNTI) Always Below 1 Ω
C46-47 (VNO2) - A48-20 (VNO2) Always Below 1 Ω
C46-48 (VNI2) - A48-11 (VNI2) Always Below 1 Ω


Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C45-49 (VNTO) or A48-5 (VNTO) - Body ground Always 10 kΩ or higher
C45-50 (VNTI) or A48-4 (VNTI) - Body ground Always 10 kΩ or higher
C45-47 (VNO2) or A48-20 (VNO2) - Body ground Always 10 kΩ or higher
C45-48 (VNI2) or A48-11 (VNI2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-49 (VNTO) or A48-5 (VNTO) - Body ground Always 10 kΩ or higher
C46-50 (VNTI) or A48-4 (VNTI) - Body ground Always 10 kΩ or higher
C46-47 (VNO2) or A48-20 (VNO2) - Body ground Always 10 kΩ or higher
C46-48 (VNI2) or A48-11 (VNI2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT TURBO MOTOR DRIVER (for Bank 1 and Bank 2)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR (TURBO MOTOR DRIVER - ECM)
3.INSPECT TURBO MOTOR DRIVER (for Bank 1 and Bank 2)
a.

Connect the intelligent tester to the DLC3.



c.

Turn the engine switch off.


d.

Remove the rear fender splash shield sub-assembly RH.


e.

Remove the front fender liner LH.


f.

Disconnect the turbo motor driver connector.


g.

Reconnect the turbo motor driver connector.


h.

Turn the engine switch on (IG) and turn the tester on.


i.

After starting the engine, idle it for 5 seconds.


j.

Enter the following menus: Powertrain / Engine / DTC.


k.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
DTC is output A
DTC is not output B




A

4.REPLACE TURBO MOTOR DRIVER

B

END

4.REPLACE TURBO MOTOR DRIVER
a.

Replace the turbo motor driver (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>TURBO MOTOR DRIVER>REMOVAL).

NOTICE:

Make sure that foreign matter does not enter the connector(s) when replacing parts.




NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.



c.

Turn the engine switch off.


d.

Turn the engine switch on (IG) and turn the tester on.


e.

After starting the engine, idle it for 5 seconds.


f.

Enter the following menus: Powertrain / Engine / DTC.


g.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
DTC is output A
DTC is not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR (TURBO MOTOR DRIVER - ECM)

NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

After starting the engine, idle it for 5 seconds.


e.

Enter the following menus: Powertrain / Engine / DTC.


f.

Confirm that the DTC is not output again.



NEXT

END