Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/o DPF) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254984 ECD SYSTEM(w/o DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/o DPF)  P1258  VNT Position Sensor Range/Performance Bank 2 Sensor 1  P1259  VNT Position Sensor Low Bank 2 Sensor 1  P1260  VNT Position Sensor High Bank 2 Sensor 1  P1262  VNT Position Sensor Low Bank 2 Sensor 2  P1263  VNT Position Sensor High Bank 2 Sensor 2  P2563  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance  P2564  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low  P2565  Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High  P2588  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low  P2589  Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High  


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.

The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the turbo motor driver. The turbo motor driver determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A183002E03
4.208,1.458 4.208,0.604 false 4.208,0.604 4.563,0.604 false 1.146,2.604 0.854,3.208 false 1.385,3.073 1.51,3.302 false 1.167,2.208 0.719,1.208 false 1.385,1.677 1.563,1.198 false 0.719,1.208 0.813,1.208 false 1.552,1.208 1.656,1.208 false 0.5,3.875 2.406,4.302 1.906,0.427 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly) 0.865,1.135 1.417,1.302 0.552,0.167 10 false IC No. 1 0.594,3.302 1.24,3.51 0.646,0.208 10 false IC No. 2 3.021,1.896 3.417,2.073 0.396,0.177 10 false VTAI 3.021,2.188 3.417,2.365 0.396,0.177 10 false VNE2 3.021,1.542 3.479,1.719 0.458,0.177 10 false VNVC 3.021,2.802 3.396,2.979 0.375,0.177 10 false VTA 3.021,3.135 3.396,3.313 0.375,0.177 10 false E2S 3.021,2.49 3.448,2.667 0.427,0.177 10 false VCS 2.938,3.531 3.771,3.906 0.833,0.375 10 false Turbo Motor Driver 4.719,3.604 5.229,3.781 0.51,0.177 10 false Closed 5.76,3.604 6.344,3.781 0.583,0.177 10 false Opened 1.698,1.135 2.25,1.344 0.552,0.208 10 false Magnet 4.635,0.5 6.542,0.896 1.906,0.396 10 false Nozzle Vane Position Sensor Output Voltage (V) 0.073,2.74 0.542,3.125 0.469,0.385 10 false Sensor Vane 4.042,1.646 4.365,1.823 0.323,0.177 10 false 4.5 4.052,2.833 4.385,3.031 0.333,0.198 10 false 0.5 1.448,3.333 2.01,3.542 0.563,0.208 10 false Magnet 4.771,3.219 6.167,3.531 1.396,0.313 10 true Nozzle Vane Position

P1258
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second The difference between VTI2 and VTA2 voltage is 0.8 V or more for 0.5 seconds (1 trip detection logic). Nozzle vane position sensor (turbocharger sub-assembly)

P1259
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTI2 voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P1260
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTI2 voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P1262
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTA2 voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P1263
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTA2 voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P2563
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second The difference between VTAI and VTA voltage is 0.8 V or more for 0.5 seconds (1 trip detection logic). Nozzle vane position sensor (turbocharger sub-assembly)

P2564
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTAI voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P2565
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTAI voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P2588
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTA voltage is 0.5 V or less for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



P2589
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 1 second VTA voltage is 4.5 V or more for 0.5 seconds (1 trip detection logic).
·

Nozzle vane position sensor (turbocharger sub-assembly)

·

Open or short in nozzle vane position sensor circuit

·

Turbo motor driver



HINT:

If DTC P1258, P1259, P1260, P1262, P1263, P2563, P2564, P2565, P2588 and/or P2589 is stored, the following symptoms may appear:

Stuck open malfunction:

- Lack of power

- Vehicle surge or hesitation under light or medium load

- White smoke



WIRING DIAGRAM

A325135E02
0.406,3.219 3.125,3.615 2.719,0.396 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly (for Bank 1)) 2.073,0.75 2.219,0.927 0.146,0.177 10 false 1 1.563,0.635 1.99,0.813 0.427,0.177 10 false VTA1 1.552,1.052 2,1.24 0.448,0.188 10 false VNE2 1.542,1.479 2.01,1.656 0.469,0.177 10 false VNVC 1.646,1.906 1.979,2.083 0.333,0.177 10 false VTA 1.656,2.333 2,2.51 0.344,0.177 10 false E2S 1.635,2.76 2.021,2.938 0.385,0.177 10 false VCS 2.073,1.167 2.219,1.344 0.146,0.177 10 false 2 2.073,1.604 2.219,1.781 0.146,0.177 10 false 3 2.073,2.021 2.219,2.198 0.146,0.177 10 false 4 2.073,2.427 2.219,2.604 0.146,0.177 10 false 5 2.073,2.844 2.219,3.021 0.146,0.177 10 false 6 5.052,0.75 5.281,0.958 0.229,0.208 10 false 21 5.063,1.177 5.281,1.354 0.219,0.177 10 false 12 5.125,1.604 5.292,1.781 0.167,0.177 10 false 6 5.063,2.01 5.292,2.198 0.229,0.188 10 false 22 5.052,2.427 5.281,2.615 0.229,0.188 10 false 13 5.125,2.865 5.271,3.042 0.146,0.177 10 false 7 5.344,0.521 5.771,0.708 0.427,0.188 10 false VTAI 5.344,0.948 5.813,1.146 0.469,0.198 10 false VNE2 5.344,1.344 5.781,1.521 0.438,0.177 10 false VNVC 5.344,1.771 5.75,1.948 0.406,0.177 10 false VTA 5.344,2.198 5.719,2.375 0.375,0.177 10 false E2S 5.344,2.615 5.719,2.792 0.375,0.177 10 false VCS 0.365,7.01 3.052,7.406 2.688,0.396 10 false Nozzle Vane Position Sensor (Turbocharger Sub-assembly (for Bank 2)) 2.031,4.51 2.177,4.688 0.146,0.177 10 false 1 1.594,4.438 1.938,4.615 0.344,0.177 10 false VTI2 1.594,4.823 1.938,5 0.344,0.177 10 false VE2 1.521,5.26 1.938,5.438 0.417,0.177 10 false VNC2 1.552,5.667 1.938,5.844 0.385,0.177 10 false VTA2 1.531,6.094 1.927,6.271 0.396,0.177 10 false E2S2 1.521,6.5 1.938,6.677 0.417,0.177 10 false VCS2 2.031,4.927 2.177,5.104 0.146,0.177 10 false 2 2.031,5.333 2.177,5.51 0.146,0.177 10 false 3 2.031,5.771 2.177,5.948 0.146,0.177 10 false 4 2.031,6.177 2.177,6.354 0.146,0.177 10 false 5 2.031,6.604 2.177,6.781 0.146,0.177 10 false 6 5.073,4.51 5.281,4.688 0.208,0.177 10 false 23 5.052,4.927 5.271,5.104 0.219,0.177 10 false 14 5.125,5.333 5.354,5.51 0.229,0.177 10 false 8 5.073,5.76 5.281,5.938 0.208,0.177 10 false 24 5.073,6.188 5.292,6.365 0.219,0.177 10 false 15 5.146,6.615 5.292,6.792 0.146,0.177 10 false 9 5.365,4.271 5.76,4.448 0.396,0.177 10 false VTI2 5.365,4.688 5.833,4.885 0.469,0.198 10 false VE2 5.365,5.094 5.802,5.271 0.438,0.177 10 false VNC2 5.365,5.521 5.771,5.698 0.406,0.177 10 false VTA2 5.365,5.958 5.74,6.135 0.375,0.177 10 false E2S2 5.365,6.365 5.792,6.542 0.427,0.177 10 false VCS2 5.385,7.104 6.646,7.302 1.26,0.198 10 false Turbo Motor Driver 0.406,3.031 0.688,3.208 0.281,0.177 10 false C89 0.365,6.823 0.625,7 0.26,0.177 10 false z66 5.396,6.938 5.719,7.115 0.323,0.177 10 false A48

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - NOZZLE VANE POSITION SENSOR)
a.

Disconnect the nozzle vane position sensor (for Bank 1) connector.


b.

Disconnect the nozzle vane position sensor (for Bank 2) connector.


c.

Disconnect the turbo motor driver connector.

U163762E01
4.292,0.003 6.669,0.404 2.377,0.401 10 Front view of wire harness connector: (to Nozzle Vane Position Sensor) 1.083,0.018 3.459,0.419 2.377,0.401 10 Front view of wire harness connector: (to Turbo Motor Driver) 1.524,2.469 2.038,2.631 0.514,0.163 10 VTAI 2.698,2.469 3.064,2.631 0.365,0.163 10 VTI2 1.981,2.469 2.420,2.631 0.439,0.163 10 VTA 3.069,2.469 3.467,2.631 0.398,0.163 10 VTA2 1.129,2.469 1.476,2.631 0.347,0.163 10 E2S 3.169,2.101 3.682,2.264 0.514,0.163 10 E2S2 1.069,0.631 1.583,0.794 0.514,0.163 10 VCS 3.208,1.163 3.722,1.326 0.514,0.163 10 VCS2 0.677,2.469 1.102,2.631 0.426,0.163 10 VNE2 2.365,2.469 2.715,2.631 0.350,0.163 10 VE2 0.902,0.886 1.337,1.048 0.435,0.163 10 VNVC 3.168,0.869 3.607,1.032 0.438,0.163 10 VNC2 2.291,1.683 0.904,2.464 false 1.689,2.469 2.348,1.83 false 1.38,0.732 2.464,1.459 false 2.572,1.459 3.147,0.951 false 5.481,0.783 5.994,0.946 0.514,0.163 10 C91 4.836,0.783 5.350,0.946 0.514,0.163 10 C89 2.017,0.719 2.530,0.881 0.514,0.163 10 A48 2.682,1.459 3.188,1.234 false 1.338,0.947 2.356,1.455 false 2.405,1.688 1.292,2.45 false 2.514,1.688 2.513,2.439 false 2.632,1.689 3.15,2.106 false 2.118,2.457 2.442,1.83 false 2.8,2.443 2.578,1.83 false 3.069,2.469 2.672,1.83 false 3.706,2.097 4.282,2.465 0.576,0.369 10 VTA1*1 VTI2*2 4.288,2.097 4.852,2.528 0.564,0.431 10 VNE2*1 VE2*2 4.842,2.097 5.437,2.479 0.595,0.383 10 VNVC*1 VNC2*2 5.431,2.097 6.005,2.461 0.575,0.364 10 VTA*1 VTA2*2 6.001,2.097 6.542,2.528 0.541,0.431 10 E2S*1 E2S2*2 6.561,2.097 7.123,2.479 0.562,0.383 10 VCS*1 VCS2*2 5.012,1.467 4.165,2.052 false 5.217,1.475 5.083,2.062 false 5.118,1.484 4.578,2.055 false 5.442,1.484 5.993,2.066 false 5.334,1.483 5.587,2.082 false 5.546,1.489 6.568,2.062 false 5.164,0.616 5.430,0.802 0.266,0.186 10 *1 6.313,1.03 7.033,1.412 0.720,0.383 10 *1: Bank 1 *2: Bank 2 5.885,0.616 6.151,0.802 0.266,0.186 10 *2


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Bank 1
Tester Connection Condition Specified Condition
A48-21 (VTAI) - C89-1 (VTA1) Always Below 1 Ω
A48-12 (VNE2) - C89-2 (VNE2) Always Below 1 Ω
A48-6 (VNVC) - C89-3 (VNVC) Always Below 1 Ω
A48-22 (VTA) - C89-4 (VTA) Always Below 1 Ω
A48-13 (E2S) - C89-5 (E2S) Always Below 1 Ω
A48-7 (VCS) - C89-6 (VCS) Always Below 1 Ω

for Bank 2
Tester Connection Condition Specified Condition
A48-23 (VTI2) - z66-1 (VTI2) Always Below 1 Ω
A48-14 (VE2) - z66-2 (VE2) Always Below 1 Ω
A48-8 (VNC2) - z66-3 (VNC2) Always Below 1 Ω
A48-24 (VTA2) - z66-4 (VTA2) Always Below 1 Ω
A48-15 (E2S2) - z66-5 (E2S2) Always Below 1 Ω
A48-9 (VCS2) - z66-6 (VCS2) Always Below 1 Ω


Standard Resistance (Check for Short):
for Bank 1
Tester Connection Condition Specified Condition
A48-21 (VTAI) or C89-1 (VTA1) - Body ground Always 10 kΩ or higher
A48-12 (VNE2) or C89-2 (VNE2) - Body ground Always 10 kΩ or higher
A48-6 (VNVC) or C89-3 (VNVC) - Body ground Always 10 kΩ or higher
A48-22 (VTA) or C89-4 (VTA) - Body ground Always 10 kΩ or higher
A48-13 (E2S) or C89-5 (E2S) - Body ground Always 10 kΩ or higher
A48-7 (VCS) or C89-6 (VCS) - Body ground Always 10 kΩ or higher

for Bank 2
Tester Connection Condition Specified Condition
A48-23 (VTI2) or z66-1 (VTI2) - Body ground Always 10 kΩ or higher
A48-14 (VE2) or z66-2 (VE2) - Body ground Always 10 kΩ or higher
A48-8 (VNC2) or z66-3 (VNC2) - Body ground Always 10 kΩ or higher
A48-24 (VTA2) or z66-4 (VTA2) - Body ground Always 10 kΩ or higher
A48-15 (E2S2) or z66-5 (E2S2) - Body ground Always 10 kΩ or higher
A48-9 (VCS2) or z66-6 (VCS2) - Body ground Always 10 kΩ or higher




OK

2.INSPECT TURBO MOTOR DRIVER

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT TURBO MOTOR DRIVER
a.

Connect the intelligent tester to the DLC3.



c.

Turn the engine switch off.


d.

Remove the rear fender splash shield sub-assembly RH.


e.

Remove the front fender liner LH.


f.

Disconnect the turbo motor driver connector.


g.

Reconnect the turbo motor driver connector.


h.

Turn the engine switch on (IG) and turn the tester on.


i.

After starting the engine, idle it for 5 seconds.


j.

Enter the following menus: Powertrain / Engine / DTC.


k.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
DTC is output A
DTC is not output B




A

3.REPLACE TURBO MOTOR DRIVER

B

END

3.REPLACE TURBO MOTOR DRIVER
a.

Replace the turbo motor driver (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>TURBO MOTOR DRIVER>REMOVAL).

NOTICE:

Make sure that foreign matter does not enter the connector(s) when replacing parts.




NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG) and turn the tester on.


f.

After starting the engine, idle it for 5 seconds.


g.

Enter the following menus: Powertrain / Engine / DTC.


h.

Read the DTCs.

Result:
Display (DTC Output) Proceed to
DTC is output A
DTC is not output B




A

5.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2) (NOZZLE VANE POSITION SENSOR)

B

END

5.REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 or Bank 2) (NOZZLE VANE POSITION SENSOR)
a.

Replace the turbocharger sub-assembly (for Bank 1 or Bank 2) (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off.


d.

Turn the ignition switch off and leave the vehicle for 15 seconds.


e.

Turn the ignition switch to ON for 1 second.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P1258, P1259, P1260, P1262, P1263, P2563, P2564, P2565, P2588 and/or P2589.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, idle the engine.




NEXT

END