The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.
The G signal plate (No. 2 camshaft timing sprocket) has one tooth on its outer circumference and is installed on the camshaft timing chain gear. When the timing gear rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.
The NE signal plate has 34 teeth and is mounted on the No. 1 crankshaft position sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Crank engine for 4 seconds (STA on) | STA on:
No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic) |
·
Open or short in camshaft position sensor circuit ·
Camshaft position sensor ·
Crankshaft position sensor ·
No. 2 camshaft timing sprocket ·
ECM |
| Idle engine for 1 second (STA off) | STA off:
Either condition is met (1 trip detection logic): ·
Camshaft position sensor signal is not input with an engine speed of 500 rpm or more. ·
Phase deviation in crankshaft and camshaft position sensor signals with an engine speed of 500 to 3000 rpm occurs a certain number of times. |
If DTC P0340 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
Refer to DTC P0335 (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P0335).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
After performing the inspection procedure for the crankshaft position sensor, if DTC P0340 is output again, check the following items related to the camshaft position sensor.
Installation condition of the camshaft position sensor
Installation condition of the camshaft
Connection of the camshaft position sensor connector
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the camshaft position sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>INSPECTION).
OK
NG
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C66-1 - C45-80 (G+) | Always | Below 1 Ω |
| C66-2 - C45-79 (G-) | Always | Below 1 Ω |
| C66-1 or C45-80 (G+) - Body ground | Always | 10 kΩ or higher |
| C66-2 or C45-79 (G-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C66-1 - C46-80 (G+) | Always | Below 1 Ω |
| C66-2 - C46-79 (G-) | Always | Below 1 Ω |
| C66-1 or C46-80 (G+) - Body ground | Always | 10 kΩ or higher |
| C66-2 or C46-79 (G-) - Body ground | Always | 10 kΩ or higher |
Reconnect the camshaft position sensor connector.
Reconnect the ECM connector.
OK
NG
Check the sensor installation.
Sensor is installed correctly.
OK
NG
Check the condition of the timing sprocket.
Timing sprocket does not have any cracks or deformation.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the engine switch off and wait for 30 seconds or more.
Start the engine and idle it for 4 seconds or more.
Turn the GTS on.
Check the engine condition while wiggling the crankshaft position sensor wire harness for 4 seconds or more when idling.
Enter the following menus: Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| Except below | A |
| There are problem such as rough idle or engine stall when wire harness is wiggled, or DTC is output* | B |
*: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
A
B
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Replace the camshaft position sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).
NEXT
Repair or replace the harness or connector.
NEXT
Securely reinstall the sensor (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>INSTALLATION).
NEXT
Replace the No. 2 camshaft timing sprocket (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the engine switch off for 30 seconds or more.
Start the engine and idle it for 4 seconds or more.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
NEXT