Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255065 ENGINE UNIT A

1VD-FTV ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

When replacing an injector (including interchanging injectors between cylinders), common rail, cylinder head, or intake manifold, replace the corresponding injection pipes with a new one.


PROCEDURE

Hide 15777 3.DISCONNECT NO. 1 OIL COOLER HOSE

A170325E02
2.333,1.469 2.875,1.469 true 0.635,1.281 1.177,1.281 true 2.885,1.385 3.073,1.542 0.188,0.156 10 false *1 0.427,1.188 0.615,1.344 0.188,0.156 10 false *2

Text in Illustration
*1 No. 1 Oil Cooler Hose
*2 No. 2 Oil Cooler Hose

Hide 15778 4.DISCONNECT NO. 2 OIL COOLER HOSE

Hide 13471 5.REMOVE CRANKSHAFT PULLEY

NOTICE:
A181685E04
1.104,2.479 1.281,2.479 1.281,2.479 1.521,1.646 true 1.604,3.104 1.781,3.104 1.781,3.104 2.594,2.719 true 0.896,2.396 1.083,2.552 0.188,0.156 10 false *1 1.385,3.021 1.573,3.177 0.188,0.156 10 false *2

This procedure is intended for removal/installation of the crankshaft pulley only. Do not use this procedure for removal/installation of the flywheel or the drive plate and ring gear.


Text in Illustration
*1 Service Hole
*2 Protrusion

a.

Install the 2 bolts to the bolt holes of the crankshaft rear side.


b.

Using a bar, turn the crankshaft until the crankshaft pulley service hole is a little to the left of bottom dead center.


c.

Install a 14 mm x 1.5 pitch service bolt with a length of 70 mm or more to the crankshaft pulley service hole, and hold the crankshaft using the timing chain cover protrusion.


d.

Remove the 3 bolts and crankshaft pulley.

NOTICE:

If the crankshaft pulley cannot be removed, temporarily install a bolt to the crankshaft so that the pulley does not fall, and lightly tap the outer edge of the mass damper with a plastic-faced hammer to remove the pulley. Do not tap the pulley V-ribbed belt ribs, as the crankshaft may be damaged.



Hide 11348 6.REMOVE TIMING GEAR COVER SPACER (w/ Intercooler)

Hide 83520 8.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 15690 10.REMOVE OIL COOLER RELIEF VALVE ASSEMBLY

a.
A177211

Remove the oil cooler relief valve and gasket.


Hide 15609 11.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A177213

Remove the 3 bolts, 2 nuts and oil filter bracket.


b.
A177439

Remove the 2 O-rings.


Hide 89491 12.REMOVE ENGINE OIL LEVEL SENSOR

Hide 12101K 13.REMOVE OIL PAN DRAIN PLUG

a.
A177219

Remove the oil pan drain plug and gasket.


Hide 12102A 14.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 15.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12101 16.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY

Hide 12121 17.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A177220

Remove the 5 bolts and No. 1 oil pan baffle plate.


Hide 15411 18.REMOVE INLET OIL PUMP PIPE

a.
A177221

Remove the 3 bolts and inlet oil pump pipe.


b.

Remove the O-ring from the inlet oil pump pipe.


Hide 15310H 19.REMOVE OIL REGULATOR ASSEMBLY

Hide 11381 20.REMOVE REAR ENGINE OIL SEAL RETAINER

Hide 11381A 21.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A164590

Place the oil seal retainer on wooden blocks.


b.

Using a screwdriver and hammer, tap out the oil seal.

HINT:

Tape the screwdriver tip before use.



Hide 12108 24.REMOVE OIL FILLER CAP SUB-ASSEMBLY

A164467

Hide 12108A 25.REMOVE OIL FILLER CAP GASKET

Hide 11201 26.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/o DPF)

Hide 11213 27.REMOVE NOZZLE HOLDER GASKET RH (w/o DPF)

Hide 23681D 28.REMOVE NOZZLE HOLDER SEAL RH (w/o DPF)

Hide 11227 29.REMOVE CYLINDER HEAD COVER INSULATOR RH (w/ DPF)

Hide 11201 31.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH (w/ DPF)

a.
A267294

Remove the 19 bolts, 4 nozzle holder clamp seats and cylinder head cover RH.

Text in Illustration
V100135

Bolt
V100136

Nozzle Holder Clamp Seat


b.

Remove the cylinder head cover gasket RH and No. 3 cylinder head cover gasket from the cylinder head cover RH.


Hide 32.REMOVE NO. 2 FUEL PUMP BRACKET (w/ DPF)

a.
A267293

Remove the bolt and No. 2 fuel pump bracket.


Hide 11228A 33.REMOVE CYLINDER HEAD COVER INSULATOR LH (w/ DPF)

Hide 11202 36.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/ DPF)

a.
A267296

Remove the 18 bolts, 4 nozzle holder clamp seats and cylinder head cover LH.

Text in Illustration
V100135

Bolt
V100136

Nozzle Holder Clamp Seat


b.

Remove the cylinder head cover gasket LH and No. 4 cylinder head cover gasket from the cylinder head cover LH.


Hide 11202 37.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH (w/o DPF)

Hide 11214 38.REMOVE NOZZLE HOLDER GASKET LH (w/o DPF)

Hide 23681E 39.REMOVE NOZZLE HOLDER SEAL LH (w/o DPF)

Hide 11324 43.REMOVE TIMING CHAIN COVER PLATE

Hide 11302 44.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A164495E02
0.471,2.931 0.655,3.086 0.185,0.155 10 *1

Remove the 4 nuts and 16 bolts.

Text in Illustration
*1 Nut


b.

Using a screwdriver, remove the timing chain cover by prying between the timing chain cover and timing gear case.

HINT:
A385688

Tape the screwdriver tip before use.



c.
A174785

Remove the O-ring from the timing gear case.


Hide 45.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A158677E05
2.292,1.052 1.948,0.458 1.948,0.458 1.823,0.458 true 1.615,0.354 1.885,0.625 0.271,0.271 10 true *1

Place the timing chain cover on wooden blocks.

Text in Illustration
*1 Wooden Block


b.

Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 46.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the 2 crankshaft pulley set bolts to the crankshaft.


b.

Turn the crankshaft clockwise to set the No. 1 cylinder to TDC.


c.

With the crankshaft key 45° counterclockwise from the top position, check that the timing marks of the RH and LH camshaft timing gears are aligned. If not as specified, turn the crankshaft 1 revolution (360°) and align the timing marks as shown below.

A174764E05
0.438,5.969 0.438,5.844 0.438,5.844 1.021,5.688 true 0.896,4.969 1.125,5.125 0.229,0.156 10 false 45° 0.313,5.938 0.573,6.24 0.26,0.302 10 true *1 1.365,4.896 1.552,5.052 0.188,0.156 10 false *a

Text in Illustration
*1 Key - -
*a Top - -


d.

Remove the 2 crankshaft pulley set bolts.


Hide 19315 47.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A174765

Using a T30 "TORX" wrench, remove the 2 screws and crankshaft position sensor plate.


Hide 13522 48.REMOVE PUMP DRIVE SHAFT GEAR

a.
A164498E01
0.077,0.46 0.373,0.622 0.296,0.162 10 SST 0.463,0.546 0.597,0.546 0.597,0.546 0.909,1.156 false

Using SST, hold the pump drive shaft gear.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the 4 bolts and pump drive shaft gear.


Hide 13540 49.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.


b.

Push down the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


c.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

U163078E02
0.708,1.646 0.708,2.313 true 2.552,0.406 2.708,0.573 0.156,0.167 10 false A 4.448,0.417 4.604,0.583 0.156,0.167 10 false B 6.344,0.417 6.5,0.583 0.156,0.167 10 false C 0.615,2.365 0.802,2.521 0.188,0.156 10 false *1

Text in Illustration
*1 Stopper Plate - -


d.
A174766

Remove the 2 bolts and No. 1 chain tensioner.


Hide 13559 50.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

A174767

Hide 13561 51.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A164501

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13523 52.REMOVE NO. 1 CAMSHAFT TIMING SPROCKET AND NO. 1 TIMING CHAIN

A181663

Hide 53.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.

Push the tensioner slipper away from the tensioner, and move the stopper plate clockwise to release the lock as shown in A.


b.

Push up the tensioner slipper and move the stopper plate counterclockwise to set the lock as shown in B.


c.

Push the tensioner slipper away from the tensioner, and insert a hexagon wrench into the stopper plate hole as shown in C.

U163080E02
0.854,1.583 0.854,2.313 true 2.604,0.385 2.76,0.552 0.156,0.167 10 false A 4.417,0.396 4.573,0.563 0.156,0.167 10 false B 6.229,0.396 6.385,0.563 0.156,0.167 10 false C 0.76,2.365 0.948,2.521 0.188,0.156 10 false *1

Text in Illustration
*1 Stopper Plate - -


d.
A164503

Remove the 2 bolts and No. 2 chain tensioner.


Hide 54.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

A164504

Hide 55.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A180675

Remove the 2 bolts and No. 2 chain vibration damper.


Hide 13529G 56.REMOVE NO. 2 CAMSHAFT TIMING SPROCKET AND NO. 2 TIMING CHAIN

a.
A164506E04
2.979,1.219 2.979,1.552 false 2.854,1.604 3.146,1.781 0.292,0.177 10 false SST

Using SST, hold the No. 2 camshaft timing sprocket.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Remove the 4 bolts, No. 2 camshaft timing sprocket and No. 2 timing chain.


Hide 57.REMOVE FUEL SUPPLY PUMP DRIVE GEAR NUT

a.

Using SST, hold the idle gear.

SST
09960-10010  (09962-01000, 09963-00700)


b.

Remove the nut.

A257020E04
0.51,0.01 0.781,0.229 0.271,0.219 4.042,0.01 4.313,0.229 0.271,0.219 0.708,2.385 0.813,2.385 0.813,2.385 1.948,1.76 true 4.24,2.385 4.344,2.385 4.344,2.385 5.479,1.76 true 0.385,2.313 0.719,2.458 0.333,0.146 10 false SST 3.917,2.313 4.25,2.458 0.333,0.146 10 false SST 0.552,0.042 0.74,0.198 0.188,0.156 10 false *A 4.094,0.042 4.281,0.198 0.188,0.156 10 false *B

Text in Illustration
*A w/ Intercooler *B w/o Intercooler


Hide 13520A 58.REMOVE IDLE GEAR ASSEMBLY

a.
A180280

w/ Intercooler:

Using an 8 mm x 1.25 pitch service bolt with a length of 15 mm or more, fix the idle gear in place.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.
A257018E04
0.104,0.094 0.365,0.396 0.26,0.302 10 true *A 0.104,2.49 0.406,2.76 0.302,0.271 10 true *B

Remove the 2 bolts, idle gear thrust plate and idle gear.

Text in Illustration
*A w/ Intercooler
*B w/o Intercooler


Hide 59.SEPARATE SUB IDLE GEAR, IDLE GEAR SPRING AND IDLE GEAR (w/ Intercooler)

a.
A177419

Hold the idle gear in a vise between aluminum plates.

NOTICE:

Be careful not to damage the gears.



b.
A177420E01
0.295,0.224 0.590,0.373 0.295,0.149 10 SST 0.676,0.317 0.854,0.317 0.854,0.317 1.041,0.741 false

Using SST, hole the idle gear, and remove the bolt and sub idle gear.

SST
09960-10010  (09962-01000, 09963-00700)


c.
A177421

Remove the idle gear spring from the idle gear.


Hide 13581 60.REMOVE NO. 1 IDLE GEAR SHAFT

A164511

Hide 13613 61.REMOVE FUEL SUPPLY PUMP DRIVE GEAR

a.
A164509E02
1.073,1.344 0.656,1.719 0.656,1.719 0.656,1.823 true 0.521,1.885 0.823,2.031 0.302,0.146 10 false SST

Using SST, remove the fuel supply pump drive gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)


Hide 62.INSPECT RADIAL BALL BEARING

a.
A164845

Turn the bearing, and check that the bearing moves smoothly and quietly.

If it moves roughly or noisily, replace the radial ball bearing.


Hide 63.REMOVE RADIAL BALL BEARING

A158678E01
0.357,0.961 0.673,1.117 0.317,0.156 10 SST 1.324,1.04 0.769,1.04 false

HINT:

It is not necessary to remove the bearing unless it is being replaced.


a.

Using SST, remove the radial ball bearing.

SST
09950-00020  
09950-00030  
09950-60010  (09951-00580)
09950-40011  (09957-04010)


Hide 13616 64.SEPARATE FUEL SUPPLY PUMP DRIVE GEAR AND FUEL SUPPLY PUMP SHAFT SPROCKET

a.
A158679

Hold the fuel supply pump shaft sprocket in a vise between aluminum plates.

NOTICE:

Be careful not to damage the gears.



b.

Remove the 4 bolts and separate the fuel supply pump drive gear and fuel supply pump shaft sprocket.


Hide 65.REMOVE STRAIGHT PIN

HINT:
A158649

It is not necessary to remove the straight pin unless it is being replaced.


a.

Remove the straight pin.


Hide 22100 66.REMOVE FUEL SUPPLY PUMP ASSEMBLY

a.
A158684

Using a 6 mm hexagon wrench, remove the hexagon bolt. Then remove the 2 nuts and fuel supply pump.


b.

Remove the O-ring.


Hide 11248 67.REMOVE V-BANK SILENCER

A164488

Hide 11301 68.REMOVE TIMING GEAR CASE SUB-ASSEMBLY

a.
A164875E02
1.122,2.853 1.306,3.007 0.185,0.155 10 *1 2.135,2.853 2.320,3.007 0.185,0.155 10 *1

Remove the 22 bolts, 2 nuts and timing gear case shown in the illustration.

Text in Illustration
*1 Nut


b.
A177346

Remove the 2 O-rings and timing gear case gasket.


Hide 25770 69.DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE (w/ Intercooler)

A177331

Hide 25770A 70.DISCONNECT NO. 3 VACUUM TRANSMITTING HOSE (w/ Intercooler)

A177332

Hide 25706 71.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

a.
A177333

Remove the 2 bolts and No. 1 vacuum transmitting pipe.


Hide 25707 72.REMOVE NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

a.
A177334

Remove the 3 bolts and No. 2 vacuum transmitting pipe.


Hide 11338A 73.REMOVE NO. 2 TIMING GEAR CASE INSULATOR (w/ Intercooler)

A177335

Hide 13511 74.REMOVE NO. 1 AND NO. 2 CAMSHAFTS

a.
A164905

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 1 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
A164787

Loosen the 2 union bolts.


c.
U162919E02
0.229,0.313 0.385,0.479 0.156,0.167 10 false 1 1.198,0.906 1.375,1.083 0.177,0.177 10 false 10 0.229,0.719 0.385,0.885 0.156,0.167 10 false 2 0.813,1.917 0.99,2.083 0.177,0.167 10 false 11 0.313,1.917 0.469,2.083 0.156,0.167 10 false 3 1.198,1.25 1.375,1.417 0.177,0.167 10 false 12 0.229,1.427 0.385,1.594 0.156,0.167 10 false 4 2.031,0.26 2.208,0.427 0.177,0.167 10 false 13 3.083,0.646 3.24,0.813 0.156,0.167 10 false 5 2.417,0.896 2.594,1.073 0.177,0.177 10 false 14 3.083,0.885 3.24,1.063 0.156,0.177 10 false 6 2.021,1.917 2.198,2.083 0.177,0.167 10 false 15 3.083,1.479 3.24,1.646 0.156,0.167 10 false 7 2.427,1.26 2.604,1.427 0.177,0.167 10 false 16 3.083,1.24 3.24,1.406 0.156,0.167 10 false 8 1.406,0.271 1.583,0.438 0.177,0.167 10 false 17 0.844,0.292 1,0.458 0.156,0.167 10 false 9 1.813,0.896 1.99,1.063 0.177,0.167 10 false 18 1.417,1.917 1.594,2.083 0.177,0.167 10 false 19 1.813,1.25 1.99,1.417 0.177,0.167 10 false 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


d.
A164789

Remove the 2 union bolts and No. 1 and No. 2 oil feed pipes.


e.
A164790

Remove the 8 No. 3 camshaft bearing caps and No. 1 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



f.
A164529

Remove the No. 1 and No. 2 camshafts.


Hide 75.REMOVE NO. 2 CAMSHAFT BEARING CAP

A164530

Hide 13801 76.REMOVE NO. 1 VALVE ROCKER ARM

a.
A164531

Remove the 16 No. 1 valve rocker arms.

HINT:

Be sure to arrange the removed parts for each installation position separately.



Hide 13750 77.REMOVE NO. 1 VALVE LASH ADJUSTER ASSEMBLY

a.
A164532

Remove the 16 No. 1 valve lash adjusters.

HINT:

Be sure to arrange the removed parts for each installation position separately.



Hide 11101 78.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

a.
U162891E02
0.333,0.49 0.49,0.656 0.156,0.167 10 false 1 0.344,2.875 0.5,3.042 0.156,0.167 10 false 2 2.771,2.875 2.927,3.042 0.156,0.167 10 false 3 2.771,0.49 2.927,0.656 0.156,0.167 10 false 4 0.938,0.49 1.094,0.656 0.156,0.167 10 false 5 0.938,2.875 1.094,3.042 0.156,0.167 10 false 6 2.167,2.875 2.323,3.042 0.156,0.167 10 false 7 2.167,0.49 2.323,0.656 0.156,0.167 10 false 8 1.542,0.49 1.698,0.656 0.156,0.167 10 false 9 1.5,2.875 1.688,3.042 0.188,0.167 10 false 10

Uniformly loosen and remove the 10 bolts and 10 spacers in the sequence shown in the illustration. Then remove the cylinder head.

NOTICE:
·

Be careful not to drop washers into the cylinder head.

·

Head warpage or cracking could result from removing bolts in an incorrect order.



HINT:

Be sure to arrange the removed parts for each installation position separately.



Hide 11115 79.REMOVE NO. 1 CYLINDER HEAD GASKET

Hide 13053 80.REMOVE NO. 3 AND NO. 4 CAMSHAFTS

a.
A164905

Using a 6 mm x 1.0 pitch service bolt with a length of 16 mm or more, fix the No. 4 camshaft in place.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.
A164783

Loosen the 2 union bolts.


c.
U162918E02
0.115,0.198 0.271,0.365 0.156,0.167 10 false 1 1.302,0.865 1.479,1.042 0.177,0.177 10 false 10 0.115,0.667 0.271,0.833 0.156,0.167 10 false 2 0.896,1.896 1.073,2.063 0.177,0.167 10 false 11 0.208,1.885 0.365,2.052 0.156,0.167 10 false 3 1.302,1.24 1.479,1.417 0.177,0.177 10 false 12 0.125,1.458 0.281,1.625 0.156,0.167 10 false 4 2.167,0.188 2.344,0.354 0.177,0.167 10 false 13 3.229,0.625 3.385,0.792 0.156,0.167 10 false 5 2.563,0.854 2.74,1.021 0.177,0.167 10 false 14 3.219,0.885 3.375,1.052 0.156,0.167 10 false 6 2.156,1.896 2.333,2.063 0.177,0.167 10 false 15 3.229,1.49 3.385,1.656 0.156,0.167 10 false 7 2.552,1.24 2.729,1.406 0.177,0.167 10 false 16 3.229,1.24 3.385,1.406 0.156,0.167 10 false 8 1.51,0.198 1.688,0.365 0.177,0.167 10 false 17 0.917,0.198 1.073,0.365 0.156,0.167 10 false 9 1.917,0.875 2.094,1.042 0.177,0.167 10 false 18 1.542,1.906 1.719,2.073 0.177,0.167 10 false 19 1.927,1.25 2.104,1.417 0.177,0.167 10 false 20

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


d.
A164785

Remove the 2 union bolts and No. 3 and No. 4 oil feed pipes.


e.
A164786

Remove the 8 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Be sure to arrange the removed parts for each installation position separately.



f.
A164537

Remove the No. 3 and No. 4 camshafts.


Hide 81.REMOVE NO. 5 CAMSHAFT BEARING CAP

A164538

Hide 82.REMOVE NO. 2 VALVE ROCKER ARM

a.
A164539

Remove the 16 No. 2 valve rocker arms.

HINT:

Be sure to arrange the removed parts for each installation position separately.



Hide 83.REMOVE NO. 2 VALVE LASH ADJUSTER ASSEMBLY

a.
A164540

Remove the 16 No. 2 valve lash adjusters.

HINT:

Be sure to arrange the removed parts for each installation position separately.



Hide 11102 84.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

a.
U162893E02
2.969,2.802 3.125,2.969 0.156,0.167 10 false 1 2.917,0.385 3.073,0.552 0.156,0.167 10 false 2 0.49,2.802 0.646,2.969 0.156,0.167 10 false 4 0.521,0.396 0.677,0.563 0.156,0.167 10 false 3 2.375,2.802 2.531,2.969 0.156,0.167 10 false 5 2.333,0.396 2.49,0.563 0.156,0.167 10 false 6 1.146,0.396 1.302,0.563 0.156,0.167 10 false 7 1.115,2.792 1.271,2.958 0.156,0.167 10 false 8 1.76,2.792 1.917,2.969 0.156,0.177 10 false 9 1.698,0.396 1.885,0.563 0.188,0.167 10 false 10

Uniformly loosen and remove the 10 bolts and 10 spacers in the sequence shown in the illustration. Then remove the cylinder head.

NOTICE:
·

Be careful not to drop washers into the cylinder head.

·

Head warpage or cracking could result from removing bolts in an incorrect order.



HINT:

Be sure to arrange the removed parts for each installation position separately.



Hide 11116 85.REMOVE NO. 2 CYLINDER HEAD GASKET

Hide 86.REPLACE STUD BOLT

HINT:
A177310E02
1.917,2.273 3.099,2.450 1.182,0.177 10 20 mm (0.787 in.) 1.917,2.816 3.094,3.000 1.176,0.184 10 13 mm (0.512 in.) 0.275,2.421 0.887,2.773 0.612,0.352 10 42 mm (1.65 in.)

If the stud bolt is deformed or the threads are damaged, replace it.


a.

Intake Pipe:

i.

Using an E8 "TORX" wrench, replace the 4 stud bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)



b.

No. 3 Intake Manifold:

i.

Using an E8 "TORX" wrench, replace the 2 stud bolts labeled A.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

A385795E01
2.229,1.594 2.229,1.406 2.229,1.406 2.823,1.396 false 2.604,1.802 2.615,1.417 true 1.74,1.385 1.969,1.385 1.969,1.385 1.969,1.615 false 2.198,2.104 1.99,2.104 1.99,2.104 1.99,2.271 true 1.531,1.688 1.802,1.677 false 2.885,1.313 3.042,1.51 0.156,0.198 10 false A 5,0.354 5.156,0.552 0.156,0.198 10 false A 5.01,1.563 5.167,1.76 0.156,0.198 10 false B 2.25,2 2.406,2.198 0.156,0.198 10 false B 1.385,1.604 1.542,1.802 0.156,0.198 10 false B 1.594,1.313 1.75,1.51 0.156,0.198 10 false C 5,2.406 5.156,2.604 0.156,0.198 10 false C 4.167,0.844 4.698,1.031 0.531,0.188 10 false 42 mm 4.125,1.01 4.698,1.219 0.573,0.208 10 false (1.65 in.) 4.208,1.865 4.74,2.052 0.531,0.188 10 false 24 mm 4.167,2.031 4.792,2.24 0.625,0.208 10 false (0.945 in.) 4.177,2.896 4.708,3.083 0.531,0.188 10 false 39 mm 4.135,3.052 4.708,3.26 0.573,0.208 10 false (1.54 in.) 5.448,0.823 6.604,1.021 1.156,0.198 10 false 20 mm (0.787 in.) 5.469,1.26 6.625,1.458 1.156,0.198 10 false 13 mm (0.512 in.) 5.458,1.917 6.615,2.115 1.156,0.198 10 false 9 mm (0.354 in.) 5.458,2.135 6.615,2.333 1.156,0.198 10 false 9 mm (0.354 in.) 5.469,2.865 6.625,3.063 1.156,0.198 10 false 21 mm (0.827 in.) 5.469,3.292 6.625,3.49 1.156,0.198 10 false 9 mm (0.354 in.)


ii.

Using an E6 "TORX" wrench, replace the 2 stud bolts labeled B.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


iii.

Using an E6 "TORX" wrench, replace the stud bolt labeled C.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



c.

Oil Filter Bracket:

i.
A177312E02
0.235,2.352 0.890,2.715 0.655,0.363 10 42 mm (1.65 in.) 1.818,2.25 3.020,2.436 1.202,0.186 10 20 mm (0.787 in.) 1.818,2.761 3.007,2.942 1.189,0.180 10 13 mm (0.512 in.)

Using an E8 "TORX" wrench, replace the 2 stud bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)



d.

No. 1 Oil Pan:

i.
U163075E01
2.929,0.092 3.083,0.264 0.154,0.171 10 A 3.142,0.387 3.296,0.559 0.154,0.171 10 A 1.357,3.415 1.512,3.586 0.154,0.171 10 B 1.355,1.932 1.509,2.104 0.154,0.171 10 A 0.286,3.911 0.870,4.261 0.583,0.350 10 27 mm (1.06 in.) 2.015,3.753 3.136,3.923 1.121,0.171 10 16 mm (0.630 in.) 1.83,2.517 3.026,2.701 1.196,0.184 10 20 mm (0.787 in.) 0.286,2.479 0.949,2.870 0.663,0.392 10 42 mm (1.65 in.) 1.83,3.07 3.027,3.247 1.197,0.177 10 13 mm (0.512 in.) 2.054,4.154 3.091,4.324 1.037,0.170 10 9 mm (0.354 in.) 0.426,0.291 0.580,0.463 0.154,0.171 10 B 0.533,0.802 0.687,0.974 0.154,0.171 10 B 1.687,4.018 1.889,3.846 1.889,3.846 1.999,3.846 false 1.692,4.408 1.889,4.251 1.889,4.251 1.999,4.251 false

Using an E8 "TORX" wrench, replace the 2 stud bolts labeled A.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


ii.

Using an E7 "TORX" wrench, replace the 2 stud bolts labeled B.

Torque:
5.2 N*m (53 kgf*cm, 46 in.*lbf)



e.

Timing Chain Cover:

i.
U163076E02
1.375,0.563 1.531,0.729 0.156,0.167 10 false A 1.667,1.563 1.823,1.729 0.156,0.167 10 false A 1.219,1.573 1.375,1.74 0.156,0.167 10 false A 0.344,0.281 0.5,0.448 0.156,0.167 10 false B 0.417,0.854 0.573,1.021 0.156,0.167 10 false B 1.219,3.146 1.375,3.313 0.156,0.167 10 false B 0.333,2.24 0.917,2.583 0.583,0.344 10 false 54 mm (2.13 in.) 1.635,2.135 2.667,2.313 1.031,0.177 10 false 27 mm (1.06 in.) 1.635,2.823 2.75,3.01 1.115,0.188 10 false 12 mm (0.472 in.) 0.354,3.802 0.938,4.146 0.583,0.344 10 false 45 mm (1.77 in.) 1.635,3.615 2.792,3.792 1.156,0.177 10 false 15 mm (0.591 in.) 1.635,4.281 2.75,4.469 1.115,0.188 10 false 14 mm (0.551 in.)

Using an E7 "TORX" wrench, replace the 2 stud bolts labeled A.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


ii.

Replace the 2 stud bolts labeled B.

Torque:
12 N*m (120 kgf*cm, 9 ft.*lbf)



f.

Timing Gear Case:

i.
A180682E01
0.305,2.528 0.886,2.877 0.581,0.349 10 54 mm (2.13 in.) 2.04,2.863 3.155,3.035 1.116,0.172 10 12 mm (0.472 in.) 1.776,2.454 2.825,2.626 1.049,0.172 10 27 mm (1.06 in.) 2,2.957 1.841,2.957 1.841,2.957 1.677,3.235 false

Using an E7 "TORX" wrench, replace the 4 stud bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


ii.
A180683E01
1.673,2.419 2.798,2.587 1.125,0.168 10 16 mm (0.630 in.) 1.943,2.899 3.091,3.063 1.148,0.164 10 12 mm (0.472 in.) 1.912,2.988 1.812,2.988 1.812,2.988 1.601,3.186 false 0.18,2.629 0.768,2.969 0.588,0.339 10 40 mm (1.57 in.)

Remove the 2 stud bolts.


iii.

Remove the adhesive from the threads of the timing gear case.


iv.

Apply adhesive to 2 or more threads of the 2 stud bolts.


v.

Install the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 12101D 87.REPLACE STRAIGHT SCREW PLUG

HINT:
A177222

If water or oil leaks from the straight screw plug or the plug is corroded, replace it.


a.

No. 1 Oil Pan:

i.

Using a 10 mm hexagon wrench, replace the straight screw plug and/or gasket.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


ii.
A177223

Using a 14 mm hexagon wrench, replace the straight screw plug and/or gasket.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)



b.

Oil Filter Bracket:

i.
A177214

Using a 10 mm hexagon wrench, replace the straight screw plug and/or gasket.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)



c.

Timing Gear Case:

i.
A177320

Using a 10 mm hexagon wrench, replace the straight screw plug and/or gasket.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



Hide 11432R 88.REPLACE CYLINDER BLOCK STRAIGHT SCREW PLUG

HINT:

If water leaks from the straight screw plug or the plug is corroded, replace it.


a.
A177329

Replace the 2 straight screw plugs and 2 gaskets.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

Text in Illustration
V100136

Front


Hide 89.REPLACE RING PIN

HINT:

It is not necessary to remove the ring pin unless it is being replaced.


a.

No. 1 and No. 2 Intake Manifold:

i.
A177321E02
0.96,2.643 1.145,2.798 0.185,0.155 10 *1

Replace the ring pin.

Standard protrusion:

4.4 to 5.6 mm (0.173 to 0.222 in.)


Text in Illustration
*a 4.4 to 5.6 mm



b.

Cylinder Head:

i.
A177322E02
0.314,0.888 0.499,1.043 0.185,0.155 10 *a 0.314,2.765 0.499,2.920 0.185,0.155 10 *b 1.139,3.871 1.324,4.025 0.185,0.155 10 *c

Replace the ring pin.

Standard protrusion:

4.4 to 5.6 mm (0.173 to 0.222 in.)


Text in Illustration
*a RH
*b LH
*c 4.4 to 5.6 mm



c.

V-ribbed Belt Tensioner:

i.
A177316E02
0.965,2.699 1.150,2.854 0.185,0.155 10 *a

Replace the ring pin.

Standard protrusion:

4.7 to 5.7 mm (0.185 to 0.224 in.)


Text in Illustration
*a 4.7 to 5.7 mm



d.

Timing Chain Case:

i.
A177317E02
0.957,2.69 1.142,2.844 0.185,0.155 10 *a

Replace the ring pin.

Standard protrusion:

4.7 to 5.7 mm (0.185 to 0.224 in.)


Text in Illustration
*a 4.7 to 5.7 mm



e.

Timing Gear Case:

i.
A177315E04
1.405,2.7 1.590,2.854 0.185,0.155 10 *a

Replace the ring pin.

Standard protrusion:

5.2 to 5.7 mm (0.205 to 0.224 in.)


Text in Illustration
*a 5.2 to 5.7 mm



f.

Cylinder Head RH:

i.

Replace the ring pin.

A385796E01
0.458,0.135 0.667,0.333 0.208,0.198 10 false *a 0.448,1.438 0.656,1.635 0.208,0.198 10 false *b 5.844,1.104 6.052,1.302 0.208,0.198 10 false *c

Standard protrusion:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


Text in Illustration
*a No. 2 Camshaft Bearing Cap
*b Cylinder Head RH
*c 2.5 to 3.5 mm



g.

Cylinder Head LH:

i.

Replace the ring pin.

A385796E01
0.458,0.135 0.667,0.333 0.208,0.198 10 false *a 0.448,1.438 0.656,1.635 0.208,0.198 10 false *b 5.844,1.104 6.052,1.302 0.208,0.198 10 false *c

Standard protrusion:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


Text in Illustration
*a No. 5 Camshaft Bearing Cap
*b Cylinder Head LH
*c 2.5 to 3.5 mm



Hide 11434M 90.REPLACE CHAIN TENSIONER STRAIGHT PIN

HINT:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A177318E02
1.555,2.464 1.740,2.619 0.185,0.155 10 *a

Replace the straight pin.

Standard protrusion:

18 to 20 mm (0.709 to 0.787 in.)


Text in Illustration
*a 18 to 20 mm


Hide 11434A 91.REPLACE TIMING GEAR COVER SET STRAIGHT PIN

HINT:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A177319E02
1.575,2.658 1.760,2.813 0.185,0.155 10 *a

Replace the straight pin.

Standard protrusion:

5.0 to 7.5 mm (0.197 to 0.295 in.)


Text in Illustration
*a 5.0 to 7.5 mm


Hide 92.REPLACE HOLE PLUG (w/o Intercooler)

HINT:

It is not necessary to remove a hole plug unless it is being replaced.


a.

Remove the hole plug from the No. 4 camshaft.


b.
A257024E03
0.667,1.552 0.667,1.417 0.667,1.417 0.917,1.156 false 2.115,3.26 2.521,3.26 true 3.146,1.167 3.01,1.167 3.01,1.167 2.844,1.583 false 0.563,1.604 0.75,1.76 0.188,0.156 10 false *1 3.177,1.094 3.365,1.25 0.188,0.156 10 false *2 2.563,3.177 2.75,3.333 0.188,0.156 10 false *2

Using a 12 mm steel bar and hammer, tap in the hole plug as shown in the illustration.

Text in Illustration
*1 No. 4 Camshaft
*2 Hole Plug


Hide 93.REPLACE TIGHT PLUG (w/o Intercooler)

NOTICE:

If oil leaks from a tight plug or a plug is corroded, replace it.


a.

Remove the tight plug from the timing chain cover.


b.

Apply adhesive to a new tight plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
A257025E02
0.31,2.967 0.494,3.122 0.185,0.155 10 *a

Using SST and a hammer, tap in the tight plug as shown in the illustration.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07100)

Standard depth:

0.2 to 0.5 mm (0.00787 to 0.0197 in.)


Text in Illustration
*a 0.2 to 0.5 mm