Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

P0724
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times. Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times.
(2 trip detection logic)
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



Related Data List
DTC No. Data List
P0724 Stop Light Switch

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Engine and ECT / Data List / Stop Light Switch.


d.

Read the value displayed on the GTS when the brake pedal is depressed and released.

OK:
Brake Pedal Display
Released OFF
Depressed ON




OK

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).



OK

3.CHECK ECM (STP VOLTAGE)

NG

5.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP VOLTAGE)
U163702E02
1.771,3.365 2.521,2.719 false 0.521,0.292 0.719,0.49 0.198,0.198 10 false *a 2.208,0.292 2.406,0.49 0.198,0.198 10 false *b 1.573,2.177 1.771,2.375 0.198,0.198 10 false *c 0.25,3.073 0.583,3.281 0.333,0.208 10 false A38 2.583,2.552 3.281,2.75 0.698,0.198 10 false 13 (STP) 0.26,3.833 0.594,4 0.333,0.167 10 false A52 0.292,3.302 0.573,3.521 0.281,0.219 10 false *A 0.281,4.063 0.479,4.26 0.198,0.198 10 false *B

a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Brake Pedal Condition Specified Condition
A38-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V

for RHD
Tester Connection Brake Pedal Condition Specified Condition
A52-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V


Text in Illustration
*A for LHD
*B for RHD
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(ECM)



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Start the engine.


f.

Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Engine and ECT / Utility / All Readiness.


ii.

Input DTC P0724.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and it can be determined that the system is normal.

·

If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.






NEXT

END