The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned on (IG). The MIL goes off when the engine is started.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and GTS on.
Check the communication between the GTS and ECM.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
B
A
Disconnect the C83 throttle position sensor (for Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C83 throttle position sensor (for Bank 1) connector.
B
A
Disconnect the C84 throttle position sensor (for Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C84 throttle position sensor (for Bank 2) connector.
B
A
Disconnect the C87 No. 1 EGR valve connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C87 No. 1 EGR valve connector.
B
A
Disconnect the C88 No. 2 EGR valve connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C88 No. 2 EGR valve connector.
B
A
Disconnect the A31 accelerator pedal position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the A31 accelerator pedal position sensor connector.
B
A
Disconnect the C80 manifold absolute pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C80 manifold absolute pressure sensor connector.
B
A
Disconnect the C82 fuel pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C82 fuel pressure sensor connector.
B
A
Disconnect the N16 differential pressure sensor assembly (for Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the N16 differential pressure sensor assembly (for Bank 1) connector.
B
A
(See pageEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL)
Disconnect the C157 differential pressure sensor assembly (for Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C157 differential pressure sensor assembly (for Bank 2) connector.
B
A
(See pageEngine / Hybrid System>1VD-FTV (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR(for DPF)>REMOVAL)
Disconnect the C89 nozzle vane position sensor (for Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the C89 nozzle vane position sensor (for Bank 1) connector.
B
A
(See pageEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL)
Disconnect the z66 nozzle vane position sensor (for Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
Reconnect the z66 nozzle vane position sensor (for Bank 2) connector.
B
A
(See pageEngine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>REMOVAL)
Disconnect the throttle position sensor (for Bank 1) connector.
Disconnect the throttle position sensor (for Bank 2) connector.
Disconnect the No. 1 EGR valve connector.
Disconnect the No. 2 EGR valve connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the manifold absolute pressure sensor connector.
Disconnect the fuel pressure sensor connector.
Disconnect the differential pressure sensor assembly (for Bank 1) connector.
Disconnect the differential pressure sensor assembly (for Bank 2) connector.
Disconnect the nozzle vane position sensor (for Bank 1) connector.
Disconnect the nozzle vane position sensor (for Bank 2) connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-91 (VC) - Body ground | Always | 10 kΩ or higher |
| C45-110 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C45-118 (VCM) - Body ground | Always | 10 kΩ or higher |
| C45-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C45-66 (VCPM) - Body ground | Always | 10 kΩ or higher |
| A38-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A38-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-91 (VC) - Body ground | Always | 10 kΩ or higher |
| C46-110 (VCVL) - Body ground | Always | 10 kΩ or higher |
| C46-118 (VCM) - Body ground | Always | 10 kΩ or higher |
| C46-120 (VNVC) - Body ground | Always | 10 kΩ or higher |
| C46-66 (VCPM) - Body ground | Always | 10 kΩ or higher |
| A52-55 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A52-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
Reconnect the throttle position sensor (for Bank 1) connector.
Reconnect the throttle position sensor (for Bank 2) connector.
Reconnect the No. 1 EGR valve connector.
Reconnect the No. 2 EGR valve connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the manifold absolute pressure sensor connector.
Reconnect the fuel pressure sensor connector.
Reconnect the differential pressure sensor assembly (for Bank 1) connector.
Reconnect the differential pressure sensor assembly (for Bank 2) connector.
Reconnect the nozzle vane position sensor (for Bank 1) connector.
Reconnect the nozzle vane position sensor (for Bank 2) connector.
Reconnect the ECM connectors.
OK
NG