Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2015.08
RM2660E _51 Engine / Hybrid System _052773 1VD-FTV ENGINE CONTROL _0254999 ECD SYSTEM(w/ DPF) J

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A256646E44
0.896,0.844 2.646,1.021 1.75,0.177 10 false from EFI MAIN NO. 1 Fuse 0.823,1.198 2.594,1.406 1.771,0.208 10 false from EFI MAIN NO. 1 Relay 0.26,1.802 2.708,2.417 2.448,0.615 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.229,2.677 2.677,3.24 2.448,0.563 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.927,3.083 5.333,3.448 0.406,0.365 10 false ECM 2.958,0.729 3.406,0.906 0.448,0.177 10 false BATT 2.823,1.083 3.448,1.292 0.625,0.208 10 false +B, +B2 3.01,1.99 3.292,2.177 0.281,0.188 10 false VC 4.396,0.896 6.188,1.25 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.792 6.354,2.146 0.99,0.354 10 false Microprocessor 4.073,2.844 4.219,3.01 0.146,0.167 10 false R

When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

·

For the circuit diagram of the ECM power source circuit (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>ECM Power Source Circuit)

·

VC Power Source Circuit


A375652E01
2.226,0.746 2.488,0.908 0.262,0.163 10 VC 2.555,0.662 2.690,0.824 0.135,0.163 10 1 2.242,1.53 2.504,1.693 0.262,0.163 10 E2 2.555,1.46 2.690,1.623 0.135,0.163 10 2 2.156,1.131 2.480,1.294 0.325,0.163 10 VTA 3.536,8.07 4.430,8.233 0.894,0.163 10 *1: for LHD 3.536,8.364 4.430,8.527 0.894,0.163 10 *2: for RHD 5.488,8.406 5.882,8.569 0.394,0.163 10 ECM 2.555,1.061 2.690,1.224 0.135,0.163 10 3 0.658,1.975 0.993,2.139 0.335,0.165 10 C83 0.658,2.116 3.009,2.528 2.350,0.413 10 Throttle Position Sensor (Diesel Throttle Body Assembly (for Bank 1)) 2.226,3.274 2.488,3.437 0.262,0.163 10 VC 2.569,3.176 2.704,3.339 0.135,0.163 10 1 2.226,4.059 2.488,4.222 0.262,0.163 10 E2 2.569,3.961 2.704,4.124 0.135,0.163 10 2 2.086,3.66 2.487,3.823 0.401,0.163 10 VTA2 2.569,3.562 2.704,3.724 0.135,0.163 10 3 0.658,4.503 0.993,4.668 0.335,0.165 10 C84 2.071,6.749 2.487,6.912 0.416,0.163 10 VCP2 2.555,6.665 2.690,6.828 0.135,0.163 10 1 2.071,6.336 2.487,6.499 0.416,0.163 10 VCPA 2.555,6.252 2.690,6.415 0.135,0.163 10 4 2.085,5.935 2.501,6.098 0.416,0.163 10 VPA2 2.555,5.855 2.690,6.018 0.135,0.163 10 3 2.099,7.534 2.515,7.696 0.416,0.163 10 EPA2 2.555,7.464 2.690,7.626 0.135,0.163 10 2 2.169,7.134 2.488,7.297 0.318,0.163 10 EPA 2.555,7.064 2.690,7.227 0.135,0.163 10 5 2.169,5.52 2.488,5.683 0.318,0.163 10 VPA 5.048,6.739 5.464,6.902 0.416,0.163 10 VCP2 5.048,6.336 5.464,6.499 0.416,0.163 10 VCPA 5.048,5.939 5.464,6.102 0.416,0.163 10 VPA2 5.048,7.536 5.464,7.699 0.416,0.163 10 EPA2 5.048,7.136 5.367,7.299 0.318,0.163 10 EPA 5.048,5.528 5.367,5.691 0.318,0.163 10 VPA 4.682,5.528 5.001,5.691 0.318,0.163 10 A52 4.674,5.345 5.020,5.508 0.346,0.163 10 53*2 4.324,5.345 4.670,5.508 0.346,0.163 10 53*1 4.682,5.927 5.001,6.090 0.318,0.163 10 A52 4.66,5.744 4.987,5.907 0.327,0.163 10 54*2 5.048,3.669 5.464,3.832 0.416,0.163 10 VLU2 4.682,3.658 5.001,3.820 0.318,0.163 10 C46 4.367,3.658 4.685,3.820 0.318,0.163 10 C45 4.674,3.475 4.999,3.637 0.325,0.163 10 65*2 4.338,3.475 4.663,3.637 0.325,0.163 10 65*1 5.048,1.561 5.464,1.723 0.416,0.163 10 EVLU 4.682,1.549 5.001,1.712 0.318,0.163 10 C46 4.66,1.366 5.013,1.529 0.353,0.163 10 87*2 4.317,1.366 4.670,1.529 0.353,0.163 10 87*1 5.048,1.154 5.464,1.317 0.416,0.163 10 VLU 4.682,1.143 5.001,1.306 0.318,0.163 10 C46 4.674,0.96 5.013,1.123 0.339,0.163 10 64*2 4.345,0.96 4.684,1.123 0.339,0.163 10 64*1 5.048,0.755 5.464,0.918 0.416,0.163 10 VCVL 4.682,0.743 5.001,0.906 0.318,0.163 10 C46 4.36,1.543 4.678,1.706 0.318,0.163 10 C45 4.36,1.137 4.678,1.300 0.318,0.163 10 C45 4.36,0.737 4.678,0.900 0.318,0.163 10 C45 4.604,0.56 5.017,0.723 0.413,0.163 10 110*2 4.225,0.56 4.639,0.723 0.413,0.163 10 110*1 4.682,6.334 5.001,6.496 0.318,0.163 10 A52 4.66,6.151 5.048,6.313 0.388,0.163 10 55*2 4.682,6.732 5.001,6.895 0.318,0.163 10 A52 4.66,6.549 5.041,6.712 0.381,0.163 10 56*2 4.682,7.138 5.001,7.301 0.318,0.163 10 A52 4.66,6.955 5.041,7.118 0.381,0.163 10 57*2 4.682,7.537 5.001,7.699 0.318,0.163 10 A52 4.36,5.528 4.678,5.691 0.318,0.163 10 A38 4.36,5.927 4.678,6.090 0.318,0.163 10 A38 4.36,6.334 4.678,6.496 0.318,0.163 10 A38 4.36,6.732 4.678,6.895 0.318,0.163 10 A38 4.36,7.138 4.678,7.301 0.318,0.163 10 A38 4.36,7.537 4.678,7.699 0.318,0.163 10 A38 4.66,7.354 5.041,7.516 0.381,0.163 10 58*2 4.338,5.744 4.665,5.907 0.327,0.163 10 54*1 4.338,6.151 4.725,6.313 0.388,0.163 10 55*1 4.338,6.549 4.718,6.712 0.381,0.163 10 56*1 4.338,6.955 4.718,7.118 0.381,0.163 10 57*1 4.338,7.354 4.718,7.516 0.381,0.163 10 58*1 2.555,5.45 2.690,5.613 0.135,0.163 10 6 0.658,7.992 0.993,8.157 0.335,0.165 10 A31 0.658,8.133 2.919,8.504 2.261,0.371 10 Accelerator Pedal Position Sensor (Accelerator Pedal Rod Assembly) 0.658,4.67 3.009,5.083 2.350,0.413 10 Throttle Position Sensor (Diesel Throttle Body Assembly (for Bank 2))

A375653E01
2.048,0.425 2.513,0.588 0.465,0.163 10 VNVC 2.56,0.355 2.694,0.518 0.135,0.163 10 3 2.05,1.21 2.465,1.373 0.415,0.163 10 VNE2 2.56,1.14 2.694,1.303 0.135,0.163 10 2 2.086,0.811 2.482,0.974 0.396,0.163 10 VTA1 2.56,0.741 2.694,0.903 0.135,0.163 10 1 0.487,1.524 0.822,1.689 0.335,0.165 10 C89 0.487,1.669 3.126,2.007 2.639,0.338 10 Nozzle Vane Position Sensor (Turbocharger Sub-assembly (for Bank 1)) 2.24,5.205 2.479,5.368 0.239,0.163 10 VC 2.532,5.093 2.666,5.256 0.135,0.163 10 3 2.532,5.878 2.666,6.041 0.135,0.163 10 2 2.065,5.591 2.522,5.753 0.457,0.163 10 EGLS 2.532,5.479 2.666,5.641 0.135,0.163 10 4 5.039,5.995 5.477,6.158 0.439,0.163 10 E2 5.039,7.989 5.455,8.152 0.416,0.163 10 EGS2 5.375,8.599 5.791,8.762 0.416,0.163 10 ECM 5.025,5.185 5.420,5.348 0.395,0.163 10 VC 4.659,5.185 4.977,5.348 0.318,0.163 10 C46 4.65,5.002 4.971,5.165 0.321,0.163 10 91*2 4.673,7.977 4.991,8.140 0.318,0.163 10 C46 4.65,7.794 5.029,7.957 0.379,0.163 10 89*2 5.039,5.588 5.455,5.751 0.416,0.163 10 EGLS 4.669,5.577 4.987,5.740 0.318,0.163 10 C46 4.65,5.394 5.038,5.557 0.388,0.163 10 88*2 5.039,3.236 5.455,3.399 0.416,0.163 10 VNA2 4.665,3.228 4.983,3.391 0.318,0.163 10 C46 4.571,3.041 4.977,3.204 0.406,0.163 10 117*2 5.039,0.848 5.455,1.011 0.416,0.163 10 VNA 4.671,0.833 4.989,0.995 0.318,0.163 10 C46 4.637,0.654 4.992,0.816 0.355,0.163 10 74*2 4.673,5.992 4.991,6.155 0.318,0.163 10 C46 4.65,5.809 5.029,5.972 0.379,0.163 10 92*2 4.331,5.185 4.649,5.348 0.318,0.163 10 C45 4.322,5.002 4.643,5.165 0.321,0.163 10 91*1 4.345,7.977 4.663,8.140 0.318,0.163 10 C45 4.322,7.794 4.701,7.957 0.379,0.163 10 89*1 4.341,5.577 4.659,5.740 0.318,0.163 10 C45 4.322,5.394 4.710,5.557 0.388,0.163 10 88*1 4.344,5.992 4.663,6.155 0.318,0.163 10 C45 4.322,5.809 4.701,5.972 0.379,0.163 10 92*1 0.627,6.28 0.962,6.445 0.335,0.165 10 C87 0.627,6.421 2.822,6.751 2.195,0.330 10 EGR Valve Position Sensor (No. 1 EGR Valve) 3.178,9.306 3.334,9.490 0.156,0.184 10 A 4.005,9.306 4.160,9.490 0.156,0.184 10 B 5.025,0.449 5.441,0.612 0.416,0.163 10 VNVC 4.657,0.433 4.975,0.596 0.318,0.163 10 C46 4.581,0.254 4.996,0.417 0.416,0.163 10 120*2 4.172,3.041 4.578,3.204 0.406,0.163 10 117*1 4.181,0.254 4.597,0.417 0.416,0.163 10 120*1 5.025,1.249 5.441,1.412 0.416,0.163 10 VNE2 4.657,1.234 4.975,1.396 0.318,0.163 10 C46 4.343,3.228 4.661,3.391 0.318,0.163 10 C45 4.349,0.833 4.667,0.995 0.318,0.163 10 C45 4.335,0.433 4.653,0.596 0.318,0.163 10 C45 4.335,1.234 4.653,1.396 0.318,0.163 10 C45 4.637,1.055 4.962,1.217 0.325,0.163 10 97*2 4.314,0.654 4.669,0.816 0.355,0.163 10 74*1 4.314,1.055 4.640,1.217 0.325,0.163 10 97*1 0.571,3.976 0.906,4.141 0.335,0.165 10 z66 0.571,4.121 3.211,4.459 2.639,0.338 10 Nozzle Vane Position Sensor (Turbocharger Sub-assembly (for Bank 2)) 2.039,2.792 2.504,2.955 0.465,0.163 10 VNC2 2.551,2.75 2.685,2.913 0.135,0.163 10 3 2.125,3.577 2.429,3.739 0.304,0.163 10 VE2 2.551,3.535 2.685,3.697 0.135,0.163 10 2 2.077,3.177 2.472,3.340 0.396,0.163 10 VTI2 2.551,3.135 2.685,3.298 0.135,0.163 10 1 2.198,5.982 2.434,6.145 0.236,0.163 10 E2 2.24,7.61 2.479,7.773 0.239,0.163 10 VC 2.539,7.477 2.673,7.640 0.135,0.163 10 3 2.539,8.262 2.673,8.425 0.135,0.163 10 2 2.065,7.996 2.522,8.159 0.457,0.163 10 EGS2 2.539,7.863 2.673,8.025 0.135,0.163 10 4 0.627,8.685 0.962,8.850 0.335,0.165 10 C88 0.627,8.826 2.822,9.156 2.195,0.330 10 EGR Valve Position Sensor (No. 2 EGR Valve) 2.198,8.387 2.434,8.550 0.236,0.163 10 E2 4.885,9.067 5.703,9.230 0.818,0.163 10 *1: for LHD 4.885,9.39 5.703,9.553 0.818,0.163 10 *1: for RHD

A375654E01
2.217,0.944 2.479,1.107 0.262,0.163 10 VC 2.56,0.986 2.694,1.149 0.135,0.163 10 3 2.233,1.728 2.495,1.891 0.262,0.163 10 E2 2.56,1.784 2.694,1.947 0.135,0.163 10 1 2.156,1.329 2.478,1.492 0.322,0.163 10 PEX 2.56,1.385 2.694,1.548 0.135,0.163 10 2 0.754,2.169 1.088,2.333 0.335,0.165 10 N16 0.754,2.314 3.226,2.767 2.472,0.454 10 Differential Pressure Sensor Assembly (for Bank 1) 2.217,3.334 2.479,3.497 0.262,0.163 10 VC 2.541,3.217 2.676,3.380 0.135,0.163 10 3 2.217,4.118 2.479,4.281 0.262,0.163 10 E2 2.541,4.03 2.676,4.192 0.135,0.163 10 1 2.075,3.719 2.478,3.882 0.403,0.163 10 PEX2 2.541,3.616 2.676,3.779 0.135,0.163 10 2 0.754,4.555 1.273,4.719 0.520,0.165 10 C157 0.754,4.7 3.207,5.071 2.454,0.371 10 Differential Pressure Sensor Assembly (for Bank 2) 0.852,8.936 1.186,9.100 0.335,0.165 10 C82 0.852,9.081 2.896,9.452 2.044,0.371 10 Fuel Pressure Sensor (Common Rail Assembly (for Bank 1)) 2.24,5.64 2.479,5.802 0.239,0.163 10 VC 2.546,5.528 2.680,5.690 0.135,0.163 10 3 2.243,8.534 2.479,8.697 0.236,0.163 10 E2 2.546,8.408 2.680,8.571 0.135,0.163 10 1 2.236,8.133 2.479,8.296 0.243,0.163 10 PR 2.546,8.011 2.680,8.173 0.135,0.163 10 2 2.334,6.424 2.480,6.587 0.146,0.163 10 E 2.546,6.312 2.680,6.475 0.135,0.163 10 1 2.184,6.025 2.479,6.188 0.294,0.163 10 PIM 2.546,5.913 2.680,6.076 0.135,0.163 10 2 2.243,7.718 2.479,7.881 0.236,0.163 10 VC 5.039,8.526 5.478,8.689 0.439,0.163 10 E2M 5.039,8.129 5.455,8.292 0.416,0.163 10 PCR1 5.039,7.718 5.434,7.881 0.395,0.163 10 VCM 4.673,7.718 4.991,7.881 0.318,0.163 10 C46 4.595,7.549 5.014,7.712 0.420,0.163 10 118*2 4.212,7.549 4.631,7.712 0.420,0.163 10 118*1 4.673,8.117 4.991,8.280 0.318,0.163 10 C46 4.648,7.934 4.998,8.097 0.351,0.163 10 72*2 5.039,6.023 5.455,6.185 0.416,0.163 10 PIM 5.403,9.327 5.819,9.490 0.416,0.163 10 ECM 4.669,6.011 4.987,6.174 0.318,0.163 10 C46 4.648,5.828 5.007,5.991 0.359,0.163 10 67*2 5.039,3.74 5.455,3.903 0.416,0.163 10 PEX2 4.662,3.719 4.980,3.882 0.318,0.163 10 C46 4.651,3.549 5.067,3.712 0.416,0.163 10 70*2 5.039,1.493 5.455,1.655 0.416,0.163 10 PEX 4.661,1.467 4.979,1.629 0.318,0.163 10 C46 4.651,1.298 5.030,1.461 0.379,0.163 10 69*2 4.339,3.723 4.658,3.886 0.318,0.163 10 C45 4.329,3.554 4.745,3.717 0.416,0.163 10 70*1 4.338,1.471 4.657,1.634 0.318,0.163 10 C45 4.329,1.303 4.708,1.466 0.379,0.163 10 69*1 4.673,8.524 4.991,8.686 0.318,0.163 10 C46 4.648,8.341 4.998,8.503 0.351,0.163 10 95*2 2.546,7.592 2.680,7.755 0.135,0.163 10 3 0.852,6.785 1.186,6.949 0.335,0.165 10 C80 0.852,6.926 3.088,7.124 2.236,0.199 10 Manifold Absolute Pressure Sensor 3.15,0.308 3.306,0.492 0.156,0.184 10 A 3.977,0.308 4.132,0.492 0.156,0.184 10 B 5.018,5.625 5.461,5.787 0.443,0.163 10 VCPM 4.658,5.617 4.976,5.780 0.318,0.163 10 C46 4.648,5.43 4.976,5.593 0.328,0.163 10 66*2 4.341,7.718 4.660,7.881 0.318,0.163 10 C45 4.341,8.117 4.660,8.280 0.318,0.163 10 C45 4.316,7.934 4.667,8.097 0.351,0.163 10 72*1 4.337,6.011 4.656,6.174 0.318,0.163 10 C45 4.316,5.828 4.675,5.991 0.359,0.163 10 67*1 4.341,8.524 4.660,8.686 0.318,0.163 10 C45 4.316,8.341 4.667,8.503 0.351,0.163 10 95*1 4.326,5.617 4.645,5.780 0.318,0.163 10 C45 4.316,5.43 4.644,5.593 0.328,0.163 10 66*1 3.702,9.07 4.529,9.233 0.828,0.163 10 *1: for LHD 3.702,9.36 4.529,9.522 0.828,0.163 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Check the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

Check the communication between the GTS and ECM.

Result
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.
A351229E01
0.34,0.658 0.634,0.865 0.295,0.207 10 *1 1.033,4.039 1.328,4.245 0.295,0.207 10 *2 0.483,2.824 1.107,4.004 false

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (EFI No. 2 fuse) - Body ground Ignition switch ON 11 to 14 V


Text Illustration
*1 Engine Room Relay Block
*2 EFI No. 2 Fuse

HINT:

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR (for Bank 1))

NG

GO TO ECM POWER SOURCE CIRCUIT

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR (for Bank 1))
a.

Disconnect the throttle position sensor (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the throttle position sensor (for Bank 1) connector.



B

4.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR (for Bank 2))

A

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 1)

4.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR (for Bank 2))
a.

Disconnect the throttle position sensor (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the throttle position sensor (for Bank 2) connector.



B

5.CHECK CONNECTION BETWEEN GTS AND ECM (NO. 1 EGR VALVE POSITION SENSOR)

A

REPLACE DIESEL THROTTLE BODY ASSEMBLY (for Bank 2)

5.CHECK CONNECTION BETWEEN GTS AND ECM (NO. 1 EGR VALVE POSITION SENSOR)
a.

Disconnect the No. 1 EGR valve connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the No. 1 EGR valve connector.



B

6.CHECK CONNECTION BETWEEN GTS AND ECM (NO. 2 EGR VALVE POSITION SENSOR)

A

REPLACE NO. 1 EGR VALVE ASSEMBLY

6.CHECK CONNECTION BETWEEN GTS AND ECM (NO. 2 EGR VALVE POSITION SENSOR)
a.

Disconnect the No. 2 EGR valve connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the No. 2 EGR valve connector.



B

7.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)

A

REPLACE NO. 2 EGR VALVE ASSEMBLY

7.CHECK CONNECTION BETWEEN GTS AND ECM (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the accelerator pedal position sensor connector.



B

8.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

8.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the manifold absolute pressure sensor connector.



B

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)

A

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
a.

Disconnect the fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the fuel pressure sensor connector.



B

10.CHECK CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for Bank 1))

A

REPLACE COMMON RAIL (for Bank 1)

10.CHECK CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for Bank 1))
a.

Disconnect the differential pressure sensor assembly (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the differential pressure sensor assembly (for Bank 1) connector.



B

11.CHECK CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for Bank 2))

A

11.CHECK CONNECTION BETWEEN GTS AND ECM (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY (for Bank 2))
a.

Disconnect the differential pressure sensor assembly (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the differential pressure sensor assembly (for Bank 2) connector.



B

12.CHECK CONNECTION BETWEEN GTS AND ECM (NOZZLE VANE POSITION SENSOR (for Bank 1))

A

12.CHECK CONNECTION BETWEEN GTS AND ECM (NOZZLE VANE POSITION SENSOR (for Bank 1))
a.

Disconnect the nozzle vane position sensor (for Bank 1) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the nozzle vane position sensor (for Bank 1) connector.



B

13.CHECK CONNECTION BETWEEN GTS AND ECM (NOZZLE VANE POSITION SENSOR (for Bank 2))

A

13.CHECK CONNECTION BETWEEN GTS AND ECM (NOZZLE VANE POSITION SENSOR (for Bank 2))
a.

Disconnect the nozzle vane position sensor (for Bank 2) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result
Result Proceed to
Communication is possible A
Communication is not possible B


d.

Reconnect the nozzle vane position sensor (for Bank 2) connector.



B

14.CHECK HARNESS AND CONNECTOR

A

14.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle position sensor (for Bank 1) connector.


b.

Disconnect the throttle position sensor (for Bank 2) connector.


c.

Disconnect the No. 1 EGR valve connector.


d.

Disconnect the No. 2 EGR valve connector.


e.

Disconnect the accelerator pedal position sensor connector.


f.

Disconnect the manifold absolute pressure sensor connector.


g.

Disconnect the fuel pressure sensor connector.


h.

Disconnect the differential pressure sensor assembly (for Bank 1) connector.


i.

Disconnect the differential pressure sensor assembly (for Bank 2) connector.


j.

Disconnect the nozzle vane position sensor (for Bank 1) connector.


k.

Disconnect the nozzle vane position sensor (for Bank 2) connector.


l.

Disconnect the ECM connectors.


m.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
for LHD
Tester Connection Condition Specified Condition
C45-91 (VC) - Body ground Always 10 kΩ or higher
C45-110 (VCVL) - Body ground Always 10 kΩ or higher
C45-118 (VCM) - Body ground Always 10 kΩ or higher
C45-120 (VNVC) - Body ground Always 10 kΩ or higher
C45-66 (VCPM) - Body ground Always 10 kΩ or higher
A38-55 (VCPA) - Body ground Always 10 kΩ or higher
A38-56 (VCP2) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C46-91 (VC) - Body ground Always 10 kΩ or higher
C46-110 (VCVL) - Body ground Always 10 kΩ or higher
C46-118 (VCM) - Body ground Always 10 kΩ or higher
C46-120 (VNVC) - Body ground Always 10 kΩ or higher
C46-66 (VCPM) - Body ground Always 10 kΩ or higher
A52-55 (VCPA) - Body ground Always 10 kΩ or higher
A52-56 (VCP2) - Body ground Always 10 kΩ or higher



n.

Reconnect the throttle position sensor (for Bank 1) connector.


o.

Reconnect the throttle position sensor (for Bank 2) connector.


p.

Reconnect the No. 1 EGR valve connector.


q.

Reconnect the No. 2 EGR valve connector.


r.

Reconnect the accelerator pedal position sensor connector.


s.

Reconnect the manifold absolute pressure sensor connector.


t.

Reconnect the fuel pressure sensor connector.


u.

Reconnect the differential pressure sensor assembly (for Bank 1) connector.


v.

Reconnect the differential pressure sensor assembly (for Bank 2) connector.


w.

Reconnect the nozzle vane position sensor (for Bank 1) connector.


x.

Reconnect the nozzle vane position sensor (for Bank 2) connector.


y.

Reconnect the ECM connectors.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR