Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A266668E02
0.597,4.762 1.079,4.947 0.482,0.185 10 Battery 3.552,1.256 3.914,1.449 0.362,0.193 10 IG2D 2.915,5.046 4.871,5.384 1.956,0.339 10 *1: w/ Entry and Start System *2: w/o Entry and Start System 0.056,0.003 0.734,0.215 0.678,0.212 12 for LHD: 3.979,1.148 4.187,1.325 0.208,0.177 10 11 2.707,1.676 2.999,1.839 0.291,0.163 10 E2 2.707,1.823 3.866,1.986 1.159,0.163 10 Main Body ECU*1 1.538,4.185 1.664,4.361 0.127,0.177 10 3 1.489,4.345 1.702,4.507 0.212,0.162 10 1B 1.566,5.031 2.693,5.222 1.127,0.191 10 Integration Relay 1.538,2.587 1.664,2.763 0.127,0.177 10 1 2.348,2.605 2.475,2.782 0.127,0.177 10 1 2.608,2.605 2.735,2.782 0.127,0.177 10 2 2.348,3.835 2.475,4.012 0.127,0.177 10 1 2.608,3.835 2.735,4.012 0.127,0.177 10 2 1.489,2.747 1.702,2.909 0.212,0.162 10 1C 4.168,4.177 4.295,4.353 0.127,0.177 10 2 4.12,4.341 4.332,4.503 0.212,0.162 10 1B 4.168,3.806 4.295,3.983 0.127,0.177 10 4 4.12,3.967 4.332,4.129 0.212,0.162 10 1B 4.168,2.961 4.295,3.137 0.127,0.177 10 6 4.12,3.121 4.332,3.283 0.212,0.162 10 1B 4.168,3.347 4.295,3.524 0.127,0.177 10 7 4.12,3.508 4.332,3.670 0.212,0.162 10 1B 4.168,2.583 4.295,2.759 0.127,0.177 10 8 4.12,2.747 4.332,2.909 0.212,0.162 10 1B 5.546,2.586 5.725,2.763 0.180,0.177 10 28 5.496,2.747 5.776,2.909 0.280,0.162 10 A38 2.253,4.122 2.940,4.302 0.687,0.180 10 EFI MAIN 3.502,4.673 3.795,4.839 0.293,0.167 10 EFI 3.513,2.431 3.806,2.598 0.293,0.167 10 IG2 2.248,2.896 2.892,3.064 0.644,0.168 10 IG2 MAIN 4.881,2.603 5.008,2.780 0.127,0.177 10 1 5.137,2.603 5.264,2.780 0.127,0.177 10 2 4.928,2.869 5.233,3.037 0.304,0.168 10 IGN 5.84,2.643 6.255,2.806 0.415,0.163 10 IGSW 5.588,3.451 5.726,3.628 0.137,0.177 10 3 5.496,3.611 5.776,3.773 0.280,0.162 10 A38 5.84,3.61 6.059,3.773 0.219,0.163 10 +B 5.588,3.801 5.726,3.978 0.137,0.177 10 2 5.496,3.961 5.776,4.124 0.280,0.162 10 A38 5.84,3.961 6.156,4.123 0.316,0.163 10 +B2 5.541,4.171 5.741,4.348 0.200,0.177 10 34 5.496,4.336 5.776,4.498 0.280,0.162 10 A38 5.84,4.331 6.247,4.494 0.407,0.163 10 MREL 5.541,4.638 5.741,4.815 0.200,0.177 10 81 5.496,4.799 5.776,4.961 0.280,0.162 10 C45 5.84,4.798 6.247,4.961 0.407,0.163 10 E1 6.163,5.206 6.520,5.357 0.357,0.151 10 ECM 1.789,0.662 1.912,0.804 0.124,0.142 10 6 0.682,0.662 0.806,0.804 0.124,0.142 10 5 1.452,0.756 1.731,0.921 0.279,0.165 10 IG2 0.882,0.756 1.205,0.921 0.323,0.165 10 AM2 0.457,1.756 0.780,1.921 0.323,0.165 10 AM2 0.822,1.272 1.895,1.453 1.073,0.181 10 Ignition Switch*2 0.822,1.125 1.130,1.299 0.308,0.174 10 E93

A266669E01
0.597,4.784 1.079,4.969 0.482,0.185 10 Battery 0.056,0.024 0.734,0.236 0.678,0.212 12 for RHD: 1.538,4.206 1.664,4.383 0.127,0.177 10 3 1.489,4.366 1.702,4.528 0.212,0.162 10 1B 2.386,5.053 3.512,5.244 1.127,0.191 10 Integration Relay 1.538,2.608 1.664,2.785 0.127,0.177 10 1 2.348,2.627 2.475,2.803 0.127,0.177 10 1 2.608,2.627 2.735,2.803 0.127,0.177 10 2 2.348,3.856 2.475,4.033 0.127,0.177 10 1 2.608,3.856 2.735,4.033 0.127,0.177 10 2 1.489,2.768 1.702,2.931 0.212,0.162 10 1C 4.168,4.198 4.295,4.375 0.127,0.177 10 2 4.12,4.362 4.332,4.524 0.212,0.162 10 1B 4.168,3.828 4.295,4.004 0.127,0.177 10 4 4.12,3.988 4.332,4.150 0.212,0.162 10 1B 4.168,2.982 4.295,3.159 0.127,0.177 10 6 4.12,3.142 4.332,3.305 0.212,0.162 10 1B 4.168,3.368 4.295,3.545 0.127,0.177 10 7 4.12,3.529 4.332,3.691 0.212,0.162 10 1B 4.168,2.604 4.295,2.781 0.127,0.177 10 8 4.12,2.768 4.332,2.930 0.212,0.162 10 1B 5.546,2.608 5.725,2.784 0.180,0.177 10 28 5.496,2.768 5.776,2.930 0.280,0.162 10 A52 2.253,4.143 2.940,4.323 0.687,0.180 10 EFI MAIN 3.502,4.694 3.795,4.861 0.293,0.167 10 EFI 3.513,2.453 3.806,2.619 0.293,0.167 10 IG2 2.248,2.917 2.892,3.085 0.644,0.168 10 IG2 MAIN 4.881,2.625 5.008,2.801 0.127,0.177 10 1 5.137,2.625 5.264,2.801 0.127,0.177 10 2 4.928,2.89 5.233,3.058 0.304,0.168 10 IGN 5.84,2.664 6.255,2.827 0.415,0.163 10 IGSW 5.588,3.472 5.726,3.649 0.137,0.177 10 3 5.496,3.632 5.776,3.795 0.280,0.162 10 A52 5.84,3.632 6.059,3.795 0.219,0.163 10 +B 5.588,3.822 5.726,3.999 0.137,0.177 10 2 5.496,3.983 5.776,4.145 0.280,0.162 10 A52 5.84,3.982 6.156,4.145 0.316,0.163 10 +B2 5.541,4.193 5.741,4.369 0.200,0.177 10 34 5.496,4.357 5.776,4.519 0.280,0.162 10 A52 5.84,4.352 6.247,4.515 0.407,0.163 10 MREL 5.541,4.66 5.741,4.836 0.200,0.177 10 81 5.496,4.82 5.776,4.982 0.280,0.162 10 C46 5.84,4.819 6.247,4.982 0.407,0.163 10 E1 6.163,5.228 6.520,5.379 0.357,0.151 10 ECM 2.935,0.683 3.059,0.825 0.124,0.142 10 6 1.828,0.683 1.952,0.825 0.124,0.142 10 5 2.598,0.777 2.877,0.943 0.279,0.165 10 IG2 2.029,0.777 2.352,0.943 0.323,0.165 10 AM2 0.457,1.777 0.780,1.942 0.323,0.165 10 AM2 1.968,1.293 2.902,1.474 0.934,0.181 10 Ignition Switch 1.968,1.146 2.277,1.321 0.308,0.174 10 E93

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BATTERY)
U163263E01
0.163,0.038 2.541,0.417 2.378,0.378 10 Front view of wire harness connector: (to Engine Room Relay Block) 2.741,0.984 2.967,1.167 0.225,0.184 10 1C 2.097,2.032 3.155,2.202 1.059,0.170 10 Integration relay 1.517,2.696 2.065,2.133 false

a.

Remove the integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V




OK

2.INSPECT INTEGRATION RELAY (EFI RELAY AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INTEGRATION RELAY (EFI RELAY AND IG2 RELAY)

OK

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
A385607E01
2.292,1.146 2.719,0.542 true 0.51,1.854 0.323,2.052 true 0.563,1.854 0.531,2.031 true 0.656,1.865 0.76,2.042 true 5.76,1.458 4.99,1.115 true 5.844,1.469 5.458,2.302 true 5.958,1.792 6.385,2.333 true 0.052,0 2.479,0.49 2.427,0.49 10 false Front view of wire harness connector: (to Engine Room Relay Block) 2.813,0.438 3.865,0.688 1.052,0.25 10 false Integration Relay 0.604,1.385 0.865,1.552 0.26,0.167 10 false 1B 0.24,2.031 0.5,2.198 0.26,0.167 10 false 2 0.49,2.031 0.75,2.198 0.26,0.167 10 false 3 0.76,2.031 1.021,2.198 0.26,0.167 10 false 4 4.729,0 7.156,0.49 2.427,0.49 10 false Front view of wire harness connector: (to ECM) 5.469,0.938 5.792,1.125 0.323,0.188 10 false A38 6.135,0.938 6.458,1.125 0.323,0.188 10 false A52 5.771,0.813 6.094,1 0.323,0.188 10 false *1 6.458,0.813 6.781,1 0.323,0.188 10 false *2 4.469,1 4.969,1.229 0.5,0.229 10 false 2 (+B2) 5.26,2.323 5.76,2.552 0.5,0.229 10 false 3 (+B) 6.219,2.333 6.969,2.615 0.75,0.281 10 false 34 (MREL) 4.167,1.99 5.063,2.271 0.896,0.281 10 false *1: for LHD 4.177,2.313 5.073,2.594 0.896,0.281 10 false *2: for RHD

a.

Check the harness and the connectors between the integration relay and the ECM.

i.

Remove the integration relay from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-34 (MREL) - 1B-2 Always Below 1 Ω
A38-3 (+B) - 1B-4 Always Below 1 Ω
A38-2 (+B2) - 1B-4 Always Below 1 Ω
A38-34 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A38-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
A38-2 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-34 (MREL) - 1B-2 Always Below 1 Ω
A52-3 (+B) - 1B-4 Always Below 1 Ω
A52-2 (+B2) - 1B-4 Always Below 1 Ω
A52-34 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A52-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
A52-2 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the integration relay and body ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
U162837E01
2.613,2.566 3.181,2.731 0.568,0.165 10 81 (E1) 2.039,1.942 2.551,2.634 false 0.219,0.023 2.586,0.386 2.367,0.363 10 Front view of wire harness connector: (to ECM) 1.13,0.912 1.435,1.088 0.305,0.176 10 C45 0.362,2.661 1.140,2.837 0.779,0.176 10 *1: for LHD 0.362,3 1.140,3.176 0.779,0.176 10 *2: for RHD 1.542,0.766 1.717,0.941 0.175,0.176 10 *1 1.888,0.912 2.193,1.088 0.305,0.176 10 C46 2.301,0.766 2.476,0.941 0.175,0.176 10 *2

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
C46-81 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
A385610E01
2,1.927 2.563,2.521 true 2.438,3.5 2.688,4.25 true 0.26,0.125 2.656,0.677 2.396,0.552 10 false Front view of wire harness connector: (to ECM) 1.094,0.927 1.469,1.177 0.375,0.25 10 false C45 1.479,0.875 1.667,1.063 0.188,0.188 10 false *1 1.979,0.927 2.354,1.177 0.375,0.25 10 false C46 2.396,0.865 2.583,1.052 0.188,0.188 10 false *2 2.625,2.448 3.24,2.698 0.615,0.25 10 false 81 (E1) 1.094,2.719 1.469,2.969 0.375,0.25 10 false A38 1.479,2.667 1.667,2.854 0.188,0.188 10 false *1 1.99,2.719 2.365,2.969 0.375,0.25 10 false A52 2.365,2.656 2.552,2.844 0.188,0.188 10 false *2 2.375,4.26 3.24,4.51 0.865,0.25 10 false 28 (IGSW) 0.083,3.917 1.073,4.229 0.99,0.313 10 false *1: for LHD 0.094,4.219 1.083,4.531 0.99,0.313 10 false *2: for RHD

a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Ignition switch ON 11 to 14 V

for RHD
Tester Connection Switch Condition Specified Condition
A52-28 (IGSW) - C46-81 (E1) Ignition switch ON 11 to 14 V




OK

NG

6.INSPECT FUSE (IGN)
6.INSPECT FUSE (IGN)
A162270E02
0.255,0.137 1.952,0.293 1.698,0.156 10 Engine Room Relay Block: 2.694,2.987 3.001,3.155 0.306,0.168 10 IGN 2.682,2.285 2.821,2.961 false

a.

Remove the IGN fuse from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
IGN fuse Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)

NG

CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE

7.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
A385607E02
2.292,1.146 2.719,0.542 true 0.969,1.854 1.135,2.073 true 6.313,1.594 6.521,2.313 true 0.052,0 2.479,0.49 2.427,0.49 10 false Front view of wire harness connector: (to Engine Room Relay Block) 2.813,0.438 3.865,0.688 1.052,0.25 10 false Integration Relay 0.604,1.385 0.865,1.552 0.26,0.167 10 false 1B 1.156,2.063 1.417,2.229 0.26,0.167 10 false 8 4.729,0 7.156,0.49 2.427,0.49 10 false Front view of wire harness connector: (to ECM) 5.469,0.938 5.792,1.125 0.323,0.188 10 false A38 6.135,0.938 6.458,1.125 0.323,0.188 10 false A52 5.771,0.813 6.094,1 0.323,0.188 10 false *1 6.458,0.813 6.781,1 0.323,0.188 10 false *2 6.198,2.344 6.948,2.625 0.75,0.281 10 false 28 (IGSW) 4.167,1.99 5.063,2.271 0.896,0.281 10 false *1: for LHD 4.177,2.313 5.073,2.594 0.896,0.281 10 false *2: for RHD

a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
1B-8 - A38-28 (IGSW) Always Below 1 Ω
1B-8 or A38-28 (IGSW) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
1B-8 - A52-28 (IGSW) Always Below 1 Ω
1B-8 or A52-28 (IGSW) - Body ground Always 10 kΩ or higher




OK

8.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B


A

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE ROOM RELAY BLOCK)

B

11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE ROOM RELAY BLOCK)
A385625E01
0.906,1.854 0.479,2.281 true 5.688,1.146 5.927,0.583 5.927,0.583 6.042,0.583 true 4.25,1.854 4.333,2.031 true 0.135,0.021 2.458,0.427 2.323,0.406 10 false Front view of wire harness connector: (to Main Body ECU) 1.333,0.917 1.583,1.125 0.25,0.208 10 false E2 0.281,2.313 0.813,2.552 0.531,0.24 10 false IG2D 3.781,0 6.104,0.406 2.323,0.406 10 false Front view of wire harness connector: (to Engine Room Relay Block) 6.094,0.5 7.135,0.802 1.042,0.302 10 false Integration Relay 4.021,1.375 4.271,1.583 0.25,0.208 10 false 1B 4.333,2.01 4.583,2.219 0.25,0.208 10 false 6

a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the E2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-11 (IG2D) - 1B-6 Always Below 1 Ω
E2-11 (IG2D) or 1B-6 - Body ground Always 10 kΩ or higher




OK

10.CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
A385626E01
1.24,1.896 0.833,2.385 true 4.24,1.854 4.385,2.042 true 5.625,1.156 5.927,0.573 5.927,0.573 6.031,0.573 true 0.073,0.01 2.385,0.427 2.313,0.417 10 false Front view of wire harness connector: (to Ignition Switch) 1.302,0.917 1.583,1.104 0.281,0.188 10 false E93 0.708,2.396 0.99,2.583 0.281,0.188 10 false IG2 4.021,1.375 4.302,1.563 0.281,0.188 10 false 1B 4.385,2.052 4.667,2.24 0.281,0.188 10 false 6 3.625,0 5.958,0.458 2.333,0.458 10 false Front view of wire harness connector: (to Engine Room Relay Block) 6.104,0.469 7.156,0.844 1.052,0.375 10 false Integration Relay

a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the E93 ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E93-6 (IG2) - 1B-6 Always Below 1 Ω
1B-7 - Body ground Always Below 1 Ω
E93-6 (IG2) or 1B-6 - Body ground Always 10 kΩ or higher




OK

12.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1GR-FE (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY