Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunction detections by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the engine switch is first turned on (IG), the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A182518E15
6.198,2.427 6.563,2.583 0.365,0.156 10 false A38 6.198,2.583 6.594,2.74 0.396,0.156 10 false ECM 6.031,1 6.25,1.156 0.219,0.156 10 false W 5.75,1.208 5.948,1.365 0.198,0.156 10 false 24 4.906,1.115 5.229,1.271 0.323,0.156 10 false E8 4.906,0.927 5.104,1.083 0.198,0.156 10 false 12 2.75,1.115 3.073,1.271 0.323,0.156 10 false E7 2.708,0.917 2.906,1.073 0.198,0.156 10 false 18 3.708,1.281 4,1.448 0.292,0.167 10 false MIL 4.51,1.229 4.844,1.396 0.333,0.167 10 false CHK 3.063,1.229 3.271,1.396 0.208,0.167 10 false IG+ 1.99,0.979 2.344,1.146 0.354,0.167 10 false MET 3.375,2.083 4.625,2.25 1.25,0.167 10 false Combination Meter 0.458,1.083 1.469,1.375 1.01,0.292 10 false from IG2 relay 1.896,1.26 2.094,1.417 0.198,0.156 10 false 1 2.302,1.26 2.5,1.417 0.198,0.156 10 false 2

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Check if any DTCs are output. Note down any DTCs.



f.

Check if the MIL goes off.

Standard:

MIL goes off




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
U162914E01
0.077,0.027 2.503,0.388 2.425,0.361 10 Front view of wire harness connector: (to ECM) 1.121,0.987 1.401,1.161 0.279,0.174 10 A38 2.319,2.625 2.761,2.782 0.443,0.157 10 24 (W) 1.773,1.759 2.509,2.61 false

a.

Disconnect the A38 ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the E8 combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-24 (W) or E8-12 (CHK) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the engine switch is turned on (IG).

OK:

MIL is illuminated.




OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the engine switch on (IG).


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The intelligent tester cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the E8 combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-24 (W) - E8-12 (CHK) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR