The ECM constantly generates 5 V power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned on (IG). The MIL goes off when the engine is started.
Check that the Malfunction Indicator Lamp (MIL) lights up when turning the engine switch on (IG).
MIL lights up
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
|---|---|
| Communication is possible | A |
| Communication is not possible | B |
B
A
Disconnect the C3 throttle body connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the A31 accelerator pedal position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C59 power steering oil pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C99 camshaft position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C114 crankshaft position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C100 VVT sensor (for Intake Side of Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C121T sensor (for Exhaust Side of Bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C101 VVT sensor (for Intake Side of Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C122T sensor (for Exhaust Side of Bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
|---|---|
| MIL illuminates | A |
| MIL does not illuminate | B |
B
A
Disconnect the C3 throttle body connector.
Disconnect the A31 accelerator pedal position sensor connector.
Disconnect the C59 power steering oil pressure sensor connector.
Disconnect the C99 camshaft position sensor connector.
Disconnect the C114 crankshaft position sensor connector.
Disconnect the C100 VVT sensor (for Intake Side of Bank 1) connector.
Disconnect the C121 VVT sensor (for Exhaust Side of Bank 1) connector.
Disconnect the C101 VVT sensor (for Intake Side of Bank 2) connector.
Disconnect the C122 VVT sensor (for Exhaust Side of Bank 2) connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-80 (VCTA) - Body ground | Always | 10 kΩ or higher |
| A38-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A38-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
| C45-66 (VCV2) - Body ground | Always | 10 kΩ or higher |
| C45-67 (VCV1) - Body ground | Always | 10 kΩ or higher |
OK
NG