Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0705  Transmission Range Sensor Circuit (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0705
1.

Any 2 or more of the following signals are ON simultaneously:

-

NSW input signal is ON

-

D input signal is ON

-

R input signal is ON


2.

Any of the following conditions is met for 2 seconds or more when the shift lever is in S:

-

NSW input signal is ON

-

D input signal is ON

-

R input signal is ON


3.

All switches are off simultaneously for NSW, R and D


·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

Open or short in transmission control switch circuit

·

Transmission control switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (R, N, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required sensors/Components Park/neutral position switch assembly
Frequency of operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/o Secondary Air Injection System)>DTC CHECK / CLEAR).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on.

6.

Move the shift lever to R and wait 2 seconds or more.

7.

Move the shift lever to N and wait 2 seconds or more.

8.

Move the shift lever to D and wait 2 seconds or more.

9.

Move the shift lever to S and wait 2 seconds or more.

10.

Wait 1 minutes or more.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P0705.

15.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A374017E06
6.333,7 6.688,7.167 0.354,0.167 10 false ECM 5.771,0.573 6.135,0.833 0.365,0.26 10 false C45 5.802,0.365 6.042,0.531 0.24,0.167 10 false 49 5.75,1.688 6.115,2.021 0.365,0.333 10 false C45 5.802,1.479 6.104,1.688 0.302,0.208 10 false 26 5.813,2.573 6.083,2.771 0.271,0.198 10 false 48 6.125,0.563 6.365,0.729 0.24,0.167 10 false D 6.125,1.677 6.365,1.844 0.24,0.167 10 false R 6.094,2.781 6.542,2.948 0.448,0.167 10 false NSW 5.823,3.708 6.073,3.875 0.25,0.167 10 false 16 6.125,3.896 6.573,4.063 0.448,0.167 10 false STA 5.792,5.333 6.125,5.552 0.333,0.219 10 false A38 5.833,5.135 6.083,5.302 0.25,0.167 10 false 27 6.115,5.323 6.26,5.49 0.146,0.167 10 false S 5.771,5.938 6.052,6.146 0.281,0.208 10 false C45 5.823,5.75 6.115,6.021 0.292,0.271 10 false 81 6.125,5.927 6.479,6.094 0.354,0.167 10 false E1 2.552,0.667 2.792,0.833 0.24,0.167 10 false 4 2.573,1.781 2.813,1.948 0.24,0.167 10 false 2 2.563,2.906 2.802,3.073 0.24,0.167 10 false 3 1.396,2.896 1.635,3.063 0.24,0.167 10 false 8 1.417,1.521 1.656,1.688 0.24,0.167 10 false 6 2.323,0.563 2.563,0.729 0.24,0.167 10 false C 2.281,1.677 2.521,1.844 0.24,0.167 10 false RL 1.563,1.385 1.885,1.615 0.323,0.229 10 false IG 2.323,2.781 2.49,2.948 0.167,0.167 10 false B 1.25,3.427 4.26,3.594 3.01,0.167 10 false Park/Neutral Position Switch Assembly 0.479,5.302 1.927,6.094 1.448,0.792 10 false from ECU-IG NO. 2 Fuse 1.604,2.802 1.771,2.969 0.167,0.167 10 false L 2.646,5.781 4.479,5.948 1.833,0.167 10 false Transmission Control Switch 3.094,4.354 4.219,4.958 1.125,0.604 10 false to ST Relay Terminal 2 2.646,5.615 2.927,5.781 0.281,0.167 10 false E52 3,5.229 3.188,5.396 0.188,0.167 10 false IG 3.802,5.229 3.948,5.375 0.146,0.146 10 false S 1.229,3.271 1.542,3.448 0.313,0.177 10 false C24 2.823,5.229 2.99,5.396 0.167,0.167 10 false 3 3.979,5.208 4.146,5.375 0.167,0.167 10 false 7 5.771,2.792 6.135,3.125 0.365,0.333 10 false C45 5.771,3.906 6.104,4.125 0.333,0.219 10 false A38 0.083,6.969 1.917,7.292 1.833,0.323 10 false from ECU-IG NO. 2 Fuse

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / Powertrain / Engine / Data List / AT / Neutral Position SW Signal, Shift SW Status (R Range), Shift SW Status (D Range) and Sports Mode Selection SW.


g.

According to the display on the GTS.

Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
·

Shift lever in P or N: ON

·

Shift lever not in P or N: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (R Range) PNP switch status/
ON or OFF
·

Shift lever in R: ON

·

Shift lever not in R: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Shift SW Status (D Range) PNP switch status/
ON or OFF
·

Shift lever in D, M or S: ON

·

Shift lever not in D, M or S: OFF


When shift lever position displayed on the GTS differs from actual position, adjustment of PNP switch or shift cable may be incorrect
Sports Mode Selection SW Sport Mode Select Switch Status/
ON or OFF
·

Shift lever in S, "+" or "-": ON

·

Shift lever not in S, "+" or "-": OFF


-



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / AT / Neutral Position SW Signal, Shift SW Status (R Range), Shift SW Status (D Range)


e.

According to the display on the GTS.

OK:
Tester Display Shift Lever Position Specified Condition
Neutral Position SW Signal P or N ON
Except P or N OFF
Shift SW Status (R Range) R ON
Except R OFF
Shift SW Status (D Range) D ON
Except D OFF




OK

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

NG

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRALPOSITION SWITCH ASSEMBLY)
2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / AT / Sports Mode Selection SW.


e.

Read the values displayed on the GTS.

OK:
Tester Display Shift Lever Position Specified Condition
Sports Mode Selection SW S ON
Except S OFF




NG

3.INSPECT FLOOR SHIFT SHIFT LEVER ASSEMBLY (TRANSMISSIONCONTROL SWITCH)

OK

3.INSPECT FLOOR SHIFT SHIFT LEVER ASSEMBLY (TRANSMISSIONCONTROL SWITCH)
a.

Inspect the transmission control switch (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (ECM CONNECTOR - BODY GROUND)

NG

REPLACE FLOOR SHIFT SHIFT LEVER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ECM CONNECTOR - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Shift Lever Position Switch Condition Specified Condition
A38-27 (S) - Body ground S Engine switch on (IG) 11 to 14 V
Not in S Engine switch on (IG) 0 to 1.5 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRALPOSITION SWITCH ASSEMBLY)
U163281E01
0.153,0.128 2.686,0.477 2.533,0.349 10 Front view of wire harness connector: (to Park/Neutral Position Switch Assembly) 0.352,2.302 0.690,2.508 0.338,0.206 10 C24 1.93,3.073 2.178,3.225 0.248,0.152 10 IG 1.528,2.643 1.881,3.064 false

a.

Disconnect the C24 park/neutral position switch.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V




OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITIONSWITCH ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITIONSWITCH ASSEMBLY - ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-4 (C) - C45-49 (D) Always Below 1 Ω
C24-2 (RL) - C45-26 (R) Always Below 1 Ω
C24-3 (B) - C45-48 (NSW) Always Below 1 Ω
C24-4 (C) or C45-49 (D) - Body ground Always 10 kΩ or higher
C24-2 (RL) or C45-26 (R) - Body ground Always 10 kΩ or higher
C24-3 (B) or C45-48 (NSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR