Home › Engine / Hybrid System › 1UR-FE (LUBRICATION) › OIL PUMP › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052797 1UR-FE LUBRICATION _0255211 OIL PUMP A

1UR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53782 6.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 16400 8.REMOVE RADIATOR ASSEMBLY

Hide 88320 10.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A178491

Remove the 3 bolts, nut and stud bolt, and then disconnect the cooler compressor.

HINT:

It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



Hide 25710 11.REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 17361 12.REMOVE AIR TUBE (w/ Secondary Air Injection System)

a.
A272570

Detach the wire harness clamp.


b.

Disconnect the No. 3 air injection system hose.


c.

Remove the 2 bolts and air tube.


Hide 13.DISCONNECT ENGINE WIRE

a.

for Engine Room LH Side:

i.
A272568

Disconnect the injector connector.


ii.

Disconnect the 2 camshaft timing oil control valve connectors.


iii.

Disconnect the 4 ignition coil connectors.


iv.

Disconnect the 2 VVT sensor connectors.


v.

Disconnect the camshaft position sensor connector.


vi.

Disconnect the engine coolant temperature sensor connector.


vii.

Disconnect the noise filter connector.


viii.

Disconnect the 8 clamps.


ix.

Remove the bolt and ground wire.



b.

for Engine Room RH Side:

i.
A272569

Disconnect the 2 camshaft timing oil control valve connectors.


ii.

Disconnect the 4 ignition coil connectors.


iii.

Disconnect the 2 VVT sensor connectors.


iv.

Disconnect the injector connector.


v.

Disconnect the noise filter connector.


vi.

Disconnect the 6 clamps.



c.
A272571

Remove the bolt and disconnect the clamp and engine wire.


Hide 83520 15.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 11452 18.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 19.DISCONNECT POWER STEERING OIL PRESSURE SWITCH CONNECTOR

Hide 44310 20.DISCONNECT VANE PUMP ASSEMBLY

a.

Remove the 2 bolts and disconnect the vane pump.


Hide 23902 25.REMOVE FUEL TUBE SUB-ASSEMBLY

a.
A272572

Remove the 2 bolts and fuel tube (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 77259E 26.REMOVE FUEL HOSE

a.

Remove the fuel pipe clamp.


b.
A272573

Disconnect the 2 clamps and remove the fuel hose (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 17364A 27.REMOVE NO. 4 AIR TUBE (w/ Secondary Air Injection System)

a.
A272588E02
0.063,0.063 0.25,0.219 0.188,0.156 10 true *A 0.063,2.438 0.25,2.594 0.188,0.156 10 true *B

Remove the bolt and bracket.

Text in Illustration
*A for RHD
*B for LHD


b.
A272653

Remove the bolt, 2 nuts, 2 stud bolts, No. 4 air tube and gasket.


Hide 17363Q 28.REMOVE NO. 3 AIR TUBE (w/ Secondary Air Injection System)

a.
A272654

Remove the bolt, 2 nuts, 2 stud bolts, No. 3 air tube and gasket.


Hide 16268 29.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A272576

Disconnect the heater water hose.


b.

Remove the 2 bolts and disconnect the No. 1 water by-pass pipe.


Hide 16261L 30.DISCONNECT WATER BY-PASS HOSE

Hide 16261G 31.REMOVE NO. 1 WATER BY-PASS HOSE

Hide 16278K 32.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 16281F 33.DISCONNECT NO. 5 WATER BY-PASS HOSE

Hide 16206 34.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A272575

Disconnect the No. 2 water by-pass hose from the front water by-pass joint.


b.

Disconnect the heater hose.


c.

Remove the 2 bolts and water by-pass pipe sub-assembly.


Hide 16355 36.REMOVE FRONT WATER BY-PASS JOINT

a.
A229715

Remove the 4 nuts, water by-pass joint and 2 gaskets.


Hide 16603 38.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A210019

Remove the bolt and No. 1 idler pulley.


Hide 16211 39.REMOVE FAN BRACKET ASSEMBLY

a.
A210020

Remove the 5 bolts and fan bracket.


Hide 16620 40.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A162527

Remove the bolt, 6 mm hexagon bolt and belt tensioner.


Hide 11202 42.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A210022

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and cylinder head cover gasket LH.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A229745

Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).

Text in Illustration
V100143

Gasket


Hide 11201 43.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A210024

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and cylinder head cover gasket RH.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A229746

Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).

Text in Illustration
V100143

Gasket


Hide 13471 44.REMOVE CRANKSHAFT PULLEY

a.
A164228E12
0.188,1 0.229,1.896 0.229,1.896 0.448,1.396 true 0.063,1.917 0.385,2.104 0.323,0.188 10 false SST 3.052,1.99 3.229,2.177 0.177,0.188 10 true *a

Using SST, remove the crankshaft pulley set bolt.

SST
09213-70011  
09330-00021  

Text in Illustration
*a Hold
V100135

Turn


b.

Temporarily install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.


c.
A164229E10
0.458,0.594 0.552,0.594 0.552,0.594 0.646,1.063 true 0.083,0.51 0.396,0.688 0.313,0.177 10 false SST 3.01,2.427 3.188,2.625 0.177,0.198 10 true *a

Using the pulley set bolt and SST, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05011)

Text in Illustration
*a Hold
V100135

Turn


Hide 11302 45.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A210026

Remove the 26 bolts and nut shown in the illustration.


b.
A229747

Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

Text in Illustration
V100144

Protective Tape

NOTICE:

Be careful not to damage the cylinder head, camshaft housing and cylinder block contact surfaces of the chain cover.


HINT:

Tape the screwdriver tip before use.



c.
A210028

Remove the gasket from the cylinder block.


d.
A164415

Remove the O-ring from the oil pan.


Hide 16322 46.REMOVE WATER INLET PIPE

a.
A210029

Remove the water inlet pipe.


b.

Remove the 2 O-rings from the water inlet pipe.