Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255046 CYLINDER HEAD GASKET A

3UR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11101 3.INSTALL CYLINDER HEAD SUB-ASSEMBLY RH

a.

Clean the cylinder block with solvent.


b.

Set the piston of the No. 1 cylinder to slightly ATDC.


c.
A381397E02
0.302,1.385 0.521,1.813 0.521,1.813 0.667,1.813 false 1.552,0.26 1.781,0.448 0.229,0.188 10 false *a 0.719,1.708 0.958,1.885 0.24,0.177 10 false *1

Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

Text in Illustration
*1 Lot No.
*a Front

NOTICE:
·

Be careful of the installation direction.

·

Make sure that no oil is on the front end (indicated by the arrows) of the cylinder head gasket.




d.

Place the cylinder head on the cylinder block.

NOTICE:
·

Ensure that no oil is on the mounting surface of the cylinder head.

·

Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.



HINT:

The cylinder head bolts are tightened in 3 progressive steps.



e.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


f.
A160739E20
1.635,1.76 1.75,1.917 0.115,0.156 10 true 1 1.635,0.26 1.75,0.417 0.115,0.156 10 true 2 2.188,1.76 2.302,1.917 0.115,0.156 10 true 3 1.125,0.26 1.24,0.417 0.115,0.156 10 true 4 2.167,0.25 2.281,0.406 0.115,0.156 10 true 5 1.104,1.76 1.219,1.917 0.115,0.156 10 true 6 2.719,0.25 2.885,0.406 0.167,0.156 10 true 7 0.573,1.76 0.688,1.917 0.115,0.156 10 true 8 2.719,1.76 2.833,1.917 0.115,0.156 10 true 9 0.552,0.25 0.74,0.406 0.188,0.156 10 true 10

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



g.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts another 90°.



h.

Step 3:

i.

Tighten the cylinder head bolts an additional 90°.


ii.

Check that the paint marks are now at a 180° angle to the front.



i.
A160738E18
0.135,0.24 0.292,0.406 0.156,0.167 10 true 1 0.094,0.958 0.24,1.125 0.146,0.167 10 true 2

Install and uniformly tighten the 2 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11102 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

a.

Clean the cylinder block with solvent.


b.

Set the piston of the No. 1 cylinder to slightly ATDC.


c.
A381398E02
2.271,1.802 2.448,1.802 2.448,1.802 3.125,1.042 true 1.604,0.281 2.375,0.479 0.771,0.198 10 false *a 2,1.698 2.26,1.906 0.26,0.208 10 false *1

Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

Text in Illustration
*1 Lot No.
*a Front

NOTICE:
·

Be careful of the installation direction.

·

Make sure that no oil is on the front end (indicated by the arrows) of the cylinder head gasket.




d.

Place the cylinder head on the cylinder block.

NOTICE:
·

Ensure that no oil is on the mounting surface of the cylinder head.

·

Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.



HINT:

The cylinder head bolts are tightened in 3 progressive steps.



e.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


f.
A160737E24
1.635,1.802 1.74,1.979 0.104,0.177 10 true 1 1.635,0.271 1.74,0.448 0.104,0.177 10 true 2 1.073,1.802 1.177,1.979 0.104,0.177 10 true 3 2.177,0.271 2.281,0.448 0.104,0.177 10 true 4 2.208,1.802 2.313,1.979 0.104,0.177 10 true 6 0.531,0.271 0.635,0.448 0.104,0.177 10 true 7 2.771,1.813 2.875,1.99 0.104,0.177 10 true 8 0.521,1.802 0.625,1.979 0.104,0.177 10 true 9 2.688,0.281 2.875,0.458 0.188,0.177 10 true 10 1.094,0.281 1.198,0.458 0.104,0.177 10 true 5

Step 1:

HINT:

The cylinder head bolts are tightened in 3 progressive steps.


i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)



g.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts another 90°.



h.

Step 3:

i.

Tighten the cylinder head bolts an additional 90°.


ii.

Check that the paint marks are now at a 180° angle to the front.



i.
U152987E04
2.948,0 3.042,0.198 0.094,0.198 10 true 1 3.219,0.625 3.313,0.823 0.094,0.198 10 false 2

Install and uniformly tighten the 2 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13801 7.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 17105 9.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY