Home › Engine / Hybrid System › 3UR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2014.08–2017.08
RM2660E _51 Engine / Hybrid System _052789 3UR-FE INTAKE / EXHAUST _0255168 EXHAUST MANIFOLD A

3UR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 89467C 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

Hide 17104 3.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

a.
A236971E04
2.49,1.896 2.76,1.896 2.76,1.896 3.073,1.594 true 2.49,0.135 2.844,0.458 0.354,0.323 10 true *a 2.302,1.823 2.552,2.083 0.25,0.26 10 true *b

Install a new gasket to the cylinder head.

Text in Illustration
*a Front
*b Tab

HINT:

Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.



b.

Temporarily install the exhaust manifold sub-assembly RH with the 8 new nuts.


c.

Uniformly tighten the 8 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Attach the wire harness clamp to the bracket and connect the connector.


Hide 17167 4.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the heat insulator with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17118 5.INSTALL NO. 1 MANIFOLD STAY

a.

Temporarily install the No. 1 manifold stay with the 3 bolts.


b.
U163254E03
2.229,0.646 2.406,0.813 0.177,0.167 10 false 1 0.948,1.073 1.125,1.25 0.177,0.177 10 false 2

Tighten the 3 bolts in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17105 6.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

a.
A236972E03
3.094,1.021 3,1.021 3,1.021 2.844,1.229 true 0.656,0.156 1.125,0.469 0.469,0.313 10 true *a 3.125,0.958 3.344,1.135 0.219,0.177 10 false *b

Install a new gasket to the cylinder head.

Text in Illustration
*a Front
*b Tab

HINT:

Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.



b.

Temporarily install the exhaust manifold sub-assembly LH with the 8 new nuts.


c.

Uniformly tighten the 8 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Attach the wire harness clamp to the bracket and connect the connector.


Hide 17168 7.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.

Install the heat insulator with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17119 8.INSTALL NO. 2 MANIFOLD STAY

a.

Temporarily install the No. 2 manifold stay with the 3 bolts.


b.
U163253E02
1.052,0.563 1.229,0.729 0.177,0.167 10 false 2 2.333,0.938 2.51,1.115 0.177,0.177 10 false 1

Tighten the 3 bolts in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 37117 9.INSTALL PROPELLER SHAFT HEAT INSULATOR

a.

Install the heat insulator with the 2 bolts.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 17450B 11.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 15.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

Hide 53737B 16.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the fender apron seal with the 3 clips.


Hide 53739A 17.INSTALL FRONT FENDER APRON SEAL REAR LH

a.

Install the fender apron seal with the 4 clips.


Hide 53736G 18.INSTALL FRONT FENDER APRON SEAL FRONT RH

a.

Install the fender apron seal with the 3 clips.


Hide 53738A 19.INSTALL FRONT FENDER APRON SEAL REAR RH

a.

Install the fender apron seal with the 4 clips.


Hide 51441 20.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 21.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 22.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH