Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › DRIVE BELT › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255067 DRIVE BELT A

1VD-FTV ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL V-RIBBED BELT

a.
A179095

Attach a wrench to the V-ribbed belt tensioner bracket and turn the wrench clockwise.


b.
A174850

Install the V-ribbed belt as shown in the illustration.


c.
A185945E01
1.264,1.067 1.994,1.218 0.730,0.151 10 CORRECT 1.178,2.888 2.046,3.039 0.868,0.151 10 INCORRECT

Check that the belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.

If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.



Hide 2.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)

a.
A177431

Align the No. 3 idler pulley bracket knock pin and No. 1 idler pulley bracket knock pin hole and install the No. 3 idler pulley with the nut.

Torque:
88 N*m (898 kgf*cm, 64 ft.*lbf)


Hide 3.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)

a.
A177430

Install the collar, No. 1 idler pulley and cover with the bolt.

Torque:
49 N*m (495 kgf*cm, 36 ft.*lbf)


Hide 4.INSTALL V-RIBBED BELT (w/ Viscous Heater)

a.
A174851

Install the V-ribbed belt as shown in the illustration.


b.
A174848

Temporarily install the lock nut, and turn the bolt clockwise.


c.
A271744E02
2.073,0.781 1.958,0.781 1.958,0.781 1.823,1.156 false 2.052,0.677 2.333,0.969 0.281,0.292 10 true *a

Using a belt tension gauge, inspect the belt tension.

Standard Belt Tension:
Item Condition Specified Condition
New belt 5 to 35°C (41 to 95°F) 550 to 800 N (56 to 82 kgf, 123.6 to 179.8 lbf)
Used belt 5 to 35°C (41 to 95°F) 300 to 500 N (31 to 51 kgf, 67.4 to 112.4 lbf)


Text in Illustration
*a Measuring Point

HINT:
·

When measuring the tension of a new belt, measure the tension immediately after installing it to the engine but before starting the engine.

·

A "new belt" is a belt which has been used for less than 5 minutes on a running engine.

·

A "used belt" is a belt which has been used on a running engine for 5 minutes or more.

·

After installing a new belt, run the engine for approximately 5 minutes and then recheck the tension.




d.
A181677

Tighten the nut.

Torque:
49 N*m (495 kgf*cm, 36 ft.*lbf)


e.
A185945E01
1.264,1.067 1.994,1.218 0.730,0.151 10 CORRECT 1.178,2.888 2.046,3.039 0.868,0.151 10 INCORRECT

Check that the belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the belt has not slipped out of the groove on the bottom of the pulley.

If it has slipped out, replace the V-ribbed belt. Install a new V-ribbed belt.



Hide 17881 6.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

Hide 12601E 8.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 53292A 9.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 51405A 10.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53805 11.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53806 12.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH