Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255064 ENGINE ASSEMBLY A

1VD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).


PROCEDURE

Hide 4.REMOVE ENGINE STAND

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Lift the engine, and remove it from the engine stand.

NOTICE:
·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




Hide 32101 5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.

Using a wrench, hold the crankshaft.


b.
A267308

Install the rear crankshaft balancer weight.

Text in Illustration
V100135

Engine Side

HINT:
·

Align the pin hole of the rear crankshaft balancer weight with the pin of the crankshaft.

·

As the rear crankshaft balancer weight is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.
A267309E01
1.035,0.259 1.220,0.413 0.185,0.155 10 *1 2.975,3.077 3.159,3.231 0.185,0.155 10 *2 1.826,0.345 1.242,0.345 false 2.956,3.168 2.372,3.168 false

Install the drive plate and ring gear and rear drive plate spacer with 8 new bolts.

Text in Illustration
*1 Drive Plate and Ring Gear
*2 Rear Drive Plate Spacer
V100135

Automatic Transmission Side

HINT:

As the drive plate and ring gear and rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



d.
U163089E02
1.74,0.5 1.917,0.667 0.177,0.167 10 false 1 1.51,1.729 1.688,1.896 0.177,0.167 10 false 2 0.99,0.979 1.167,1.156 0.177,0.177 10 false 3 2.198,1.177 2.375,1.344 0.177,0.167 10 false 4 1.094,1.469 1.271,1.635 0.177,0.167 10 false 5 2.135,0.802 2.313,0.969 0.177,0.167 10 false 6 1.281,0.563 1.458,0.729 0.177,0.167 10 false 7 2,1.604 2.177,1.771 0.177,0.167 10 false 8

Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

Torque:
182 N*m (1856 kgf*cm, 134 ft.*lbf)


Hide 13405 6.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
U163091E02
1.958,0.552 2.135,0.719 0.177,0.167 10 false 1 1.292,1.677 1.469,1.844 0.177,0.167 10 false 2 1.021,0.792 1.198,0.969 0.177,0.177 10 false 3 2.188,1.385 2.365,1.552 0.177,0.167 10 false 4 0.979,1.271 1.156,1.438 0.177,0.167 10 false 5 2.198,0.875 2.375,1.042 0.177,0.167 10 false 6 1.458,0.479 1.635,0.646 0.177,0.167 10 false 7 1.781,1.708 1.958,1.875 0.177,0.167 10 false 8

Temporarily install the flywheel with 8 new bolts.

NOTICE:
·

Align the crankshaft knock pin and flywheel knock pin hole.

·

Do not strike or damage the flywheel installation bolts. Be sure to handle them carefully.

·

Make sure there is no oil on the bolts.




b.

Using a wrench, hold the crankshaft.


c.

Uniformly install and tighten the 8 bolts in the sequence shown in the illustration.

Torque:
182 N*m (1856 kgf*cm, 134 ft.*lbf)


Hide 31250 7.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 8.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 9.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine into the engine compartment.


b.

Install the 4 bolts to the front mounting insulator RH and LH.

Torque:
58 N*m (591 kgf*cm, 43 ft.*lbf)


c.

Remove the 4 bolts and No. 1 and No. 2 engine hangers.


Hide 31482 10.INSTALL CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)

a.

Install the clutch release cylinder to flexible hose tube with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 33030 11.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 23761A 17.INSTALL NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23762B 18.INSTALL NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23901H 20.INSTALL FUEL TUBE SUB-ASSEMBLY (w/ DPF)

Hide 16283 22.CONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)

Hide 23764A 23.INSTALL NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

Hide 23763 24.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

Hide 25689 25.INSTALL EGR COOLER INSULATOR (w/ EGR System)

Hide 25620 26.INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

Hide 25615A 27.INSTALL EGR PIPE INSULATOR (w/ EGR System)

Hide 17853B 28.INSTALL INTAKE MANIFOLD INSULATOR (w/ EGR System)

Hide 23763 32.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 17136 34.INSTALL NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

Hide 17135A 35.INSTALL NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

Hide 23810A 36.INSTALL COMMON RAIL ASSEMBLY RH

Hide 23711 38.INSTALL NO. 1 PROTECTOR FUEL INJECTOR (w/ DPF)

Hide 23712 39.INSTALL NO. 2 PROTECTOR FUEL INJECTOR (w/ DPF)

Hide 11224 40.INSTALL CYLINDER HEAD COVER SILENCER RH (w/ DPF)

Hide 23705 41.INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 23801L 43.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23820A 44.INSTALL COMMON RAIL ASSEMBLY LH

Hide 23765 45.INSTALL NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23764A 47.INSTALL NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 11225 48.INSTALL CYLINDER HEAD COVER SILENCER LH (w/ DPF)

Hide 25706 49.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)

Hide 25860 50.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)

Hide 23802E 51.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

Hide 23706 52.CONNECT NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 53.CONNECT ENGINE WIRE

a.

Rear Side:

i.

Install the glow plug wire harness with the nut and screw grommet.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


ii.

w/ DPF:

Connect the 3 connectors.


iii.

w/o DPF:

Connect the connector.


iv.

Install the engine wire harness protector with the 2 bolts.


v.

Install the 2 ground wires with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)



b.

LH Side:

i.

Install the engine wire protector with the 2 bolts.


ii.

Connect the 8 connectors.


iii.

Attach the wire harness clamp.


iv.

Install the engine wire harness bracket with the bolt.


v.

for RHD:

Connect the wire harness with the wire harness clamp holder.


vi.

Attach the 3 wire harness clamps and connect the 2 connectors.


vii.

w/ DPF:

Connect the 7 connectors to the injection driver.


viii.

w/o DPF:

Connect the 4 connectors to the injection driver.


ix.

Install the ground wire with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



x.

Connect the wire harness holder to the relay block.


xi.

Connect the 2 connectors to the relay block.


xii.

Connect the wire harness with the wire harness clamp holder.


xiii.

for RHD:

Connect the wire harness with the wire harness clamp holder.


xiv.

for RHD:

Connect the ECM connector to the ECM.


xv.

for RHD:

Attach the wire harness tab to the relay block.


xvi.

Connect the 4 connectors to the relay block.


xvii.

Connect the generator positive (+) cable to the body panel with the 2 clamps.


xviii.

Attach the generator positive (+) cable holder to the relay block, and install the cable to the relay block with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


xix.

Connect the wire harness with the wire harness clamp holder, and attach the ground wire clamp to the relay block side.


xx.

Install the ground wire to the body panel with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.




c.

RH Side:

i.

w/ Winch:

Install the ground wire with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


ii.

Install the engine wire harness protector with the 3 bolts.


iii.

Connect the 7 connectors.


iv.

Install the wire harness bracket with the bolt.


v.

Install the glow plug wire harness with the nut and screw grommet.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


vi.

for RHD:

Install the wire harness holder with the bolt.


vii.

for RHD:

Connect the wire harness with the wire harness holder.


viii.

for LHD:

Connect the wire harness with the wire harness clamp holder.


ix.

for LHD:

Connect the ECM connector to the ECM.


x.

for LHD:

Attach the wire harness tab to the relay block.


xi.

for LHD:

Connect the 4 connectors to the relay block.



Hide 16268M 55.INSTALL NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 23274D 56.CONNECT FUEL HOSE

Hide 17885 57.INSTALL NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 87208 58.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17877 59.INSTALL NO. 2 INTAKE AIR CONNECTOR PIPE

a.
U163186E02
2.063,3.292 2.719,3.292 true 2.729,3.208 2.917,3.365 0.188,0.156 10 false *1 1.927,3.865 2.115,4.021 0.188,0.156 10 false *a

Install the No. 2 intake air connector pipe to the No. 2 inlet compressor elbow.

Text in Illustration
*1 Hose Stopper
*a No Gap

NOTICE:

Make sure there is no gap between the air pipe and hose stopper on the elbow side.



b.

Install the bolt of the No. 2 intake air connector pipe.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Do not excessively pull the air pipe towards the front of the engine.



c.

Tighten the hose clamp on the elbow side.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:
A267325E03
1.854,1.906 1.854,1.802 1.854,1.802 1.667,1.052 true 1.854,1.792 1.542,1.042 true 1.406,3.25 1.406,4.063 true 1.75,1.927 1.938,2.083 0.188,0.156 10 false *1 1.292,4.083 1.479,4.24 0.188,0.156 10 false *1 0.792,2.823 1.063,2.979 0.271,0.156 10 false 90°

·

Align the 2 protrusions of the air pipe and elbow.

·

Install the air pipe so that the protrusion on the pipe side is within the range of the protrusion on the elbow side.

·

After tightening, a gap between the air pipe and hose stopper on the elbow side is acceptable.

·

Make sure the direction of the hose clamp is as shown in the illustration.



Text in Illustration
*1 Protrusion


d.

w/ Intercooler:

Connect the vacuum hose.


Hide 88320 61.INSTALL COOLER COMPRESSOR ASSEMBLY

a.
U163195E02
2.969,1.396 3.125,1.563 0.156,0.167 10 false 1 2.844,1.781 3,1.948 0.156,0.167 10 false 2 3.063,1.063 3.219,1.229 0.156,0.167 10 false 3 2.313,1.74 2.469,1.906 0.156,0.167 10 false 4

Temporarily install the cooler compressor with the 4 bolts.


b.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Attach the 3 wire harness clamps and connect the 4 connectors.


Hide 88711 63.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 17806 64.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 65.INSTALL NO. 2 AIR TUBE ASSEMBLY

a.

Apply a light coat of washer fluid to a new O-ring, and install it to the No. 2 air tube.


b.

Install the No. 2 air tube with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17360E 68.INSTALL NO. 1 AIR TUBE ASSEMBLY

a.

Apply a light coat of washer fluid to a new O-ring, and install it to the No. 1 air tube.


b.

Install the No. 1 air tube with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17947B 72.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 31489 74.INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

Hide 31418 76.INSTALL CLUTCH HOSE (for Manual Transmission)

Hide 87209 80.CONNECT WATER HOSE SUB-ASSEMBLY

Hide 17973 81.INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)

Hide 17973 82.INSTALL NO. 1 COOL AIR INLET (w/o Intercooler)

Hide 77251B 83.CONNECT FUEL TUBE

a.

Install new No. 1 and No. 3 fuel tube clamps.


b.

w/ DPF:

Connect the 2 fuel tubes to the clamps.


c.

w/o DPF:

Connect the 3 fuel tubes to the clamps.


Hide 41533 84.CONNECT FRONT DIFFERENTIAL BREATHER TUBE

Hide 53294C 87.CONNECT RADIATOR SIDE DEFLECTOR LH

Hide 53293C 88.CONNECT RADIATOR SIDE DEFLECTOR RH (for Manual Transmission)

Hide 32917 89.INSTALL TRANSMISSION OIL COOLER AIR DUCT (for Automatic Transmission)

Hide 52049 92.INSTALL FRONT BUMPER WINCH COVER (w/ Winch)

Hide 16371 93.INSTALL FAN PULLEY

Hide 32942 95.INSTALL OIL COOLER TUBE (for Automatic Transmission)

Hide 97.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)

Hide 98.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)

Hide 16572D 100.CONNECT NO. 2 RADIATOR HOSE

Hide 16571C 101.CONNECT NO. 1 RADIATOR HOSE

Hide 44310 102.INSTALL VANE PUMP ASSEMBLY

Hide 16470 103.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 44369A 104.INSTALL NO. 1 OIL RESERVOIR BRACKET

Hide 44360 105.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 106.INSTALL AIR CLEANER CASE

a.

Install the air cleaner case with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Attach the wire harness clamp to the air cleaner case.


Hide 17801 107.INSTALL AIR CLEANER FILTER ELEMENT

Hide 17881 109.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE

Hide 17940D 111.INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 112.INSTALL SUB-BATTERY

Hide 28800 113.INSTALL MAIN BATTERY

Hide 82113 114.INSTALL NO. 3 ENGINE ROOM WIRE

Hide 115.INSTALL FRONT WHEEL

Hide 117.CHECK FOR CLUTCH FLUID LEAK

Hide 118.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to the negative (-) main battery and sub-battery terminals.


Hide 124.INSPECT FOR EXHAUST GAS LEAK

Hide 53785B 128.INSTALL FRONT FENDER APRON SEAL REAR LH

a.

Install the front fender apron seal rear LH with the 4 clips.


Hide 53783 129.INSTALL FRONT FENDER APRON SEAL FRONT LH

a.

w/o KDSS:

Install the front fender apron seal front LH with the 4 clips.


b.

w/ KDSS:

Install the front fender apron seal front LH with the 3 clips.


Hide 53784 130.INSTALL FRONT FENDER APRON SEAL REAR RH

a.

Install the front fender apron seal rear RH with the 4 clips.


Hide 53782 131.INSTALL FRONT FENDER APRON SEAL FRONT RH

a.

Install the front fender apron seal front RH with the 3 clips.


Hide 51442 135.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 136.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Install the No. 1 engine under cover with the 10 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 53805 137.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

a.

Install the front fender splash shield RH with the clip, and then install the 3 bolts and 2 screws.


Hide 53806 138.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

a.

Install the front fender splash shield LH with the clip, and then install the 3 bolts and screw.


Hide 55781E 139.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53301 140.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Install the 2 hood supports with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:
·

As much as possible avoid touching the stroke portions of the rod to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.

·

Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.

·

Do not apply any load to the cylinders in the horizontal direction in order to prevent the rod from being deformed.

·

Install the hood support while supporting the hood by hand.




Hide 53301 141.ADJUST HOOD SUB-ASSEMBLY

Hide 53292A 146.INSTALL UPPER RADIATOR SUPPORT SEAL

Hide 12601E 147.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 148.PERFORM CRANK TIME COMPENSATION RESET FUNCTION