Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL SUB TANK › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052780 1GR-FE FUEL _0255084 FUEL SUB TANK A

1GR-FE FUEL  FUEL SUB TANK  INSTALLATION  


PROCEDURE

Hide 77213E 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A176442E05
1.698,2.396 1.823,2.396 1.823,2.396 2.094,2.698 false 1.438,4.01 1.583,4.01 1.583,4.01 2.135,3.135 true 1.479,2.302 1.667,2.458 0.188,0.156 10 false *a 1.25,3.938 1.427,4.083 0.177,0.146 10 true *b

Install the hose to the fuel sub tank as shown in the illustration.

Text in Illustration
*a Tank Side Mark
*b Hose Side Mark

HINT:
·

Align the fuel sub tank side mark with the hose side mark when installing the hose.

·
A176441E07
2.777,0.77 2.981,0.952 0.203,0.183 10 *a 2.736,0.858 2.57,0.858 2.57,0.858 2.57,1.44 false

Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.



Text in Illustration
*a Stopper


Hide 77419 2.INSTALL NO. 3 FUEL HOSE

a.
A176443E05
1.635,2.479 1.458,2.479 1.458,2.479 1.198,2.969 false 0.781,3.906 0.781,3.781 0.781,3.781 1.219,3.313 true 1.677,2.385 1.854,2.542 0.177,0.156 10 false *a 0.698,3.927 0.885,4.083 0.188,0.156 10 false *b

Install the fuel hose to the fuel sub tank as shown in the illustration.

Text in Illustration
*a Tank Side Mark
*b Hose Side Mark

HINT:
·

Align the fuel sub tank side mark with the hose side mark when installing the hose.

·
A176441E07
2.777,0.77 2.981,0.952 0.203,0.183 10 *a 2.736,0.858 2.57,0.858 2.57,0.858 2.57,1.44 false

Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.



Text in Illustration
*a Stopper


Hide 77269A 3.INSTALL FUEL TANK BREATHER HOSE

a.

Install the breather hose to the fuel sub tank.


Hide 77017 4.INSTALL FUEL AND EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

Install a new gasket to the fuel and evaporation vent tube.


b.

Install the fuel and evaporation vent tube with the 6 bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


Hide 77018E 5.INSTALL FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

except G.C.C. Countries:

Install the 2 fuel tank evaporation vent tubes.


b.

for G.C.C. Countries:

Install the fuel tank evaporation vent tube.


Hide 77259E 6.INSTALL FUEL HOSE

a.

Install the fuel hose.


Hide 83320 7.INSTALL FUEL SENDER GAUGE ASSEMBLY

a.

Install a new gasket to the sender gauge.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



b.

Install the sender gauge with the 5 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 82163 8.INSTALL FLOOR NO. 3 WIRE

a.

Attach the wire harness clamp to the fuel sub tank.


b.

Connect the sender gauge connector.


Hide 77100Z 9.INSTALL FUEL SUB TANK SUB-ASSEMBLY

a.

Set the fuel sub tank on an engine lifter and raise the fuel sub tank.


b.

Connect the 2 fuel tank bands with the 2 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


c.

Connect the floor No. 3 wire connector.


d.

Attach the 3 wire harness clamps.


Hide 77213B 10.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the hose to the filler pipe.


Hide 11.CONNECT NO. 3 FUEL HOSE

a.

Connect the fuel hose to the filler pipe.


Hide 12.CONNECT FUEL TANK BREATHER HOSE

a.

Connect the breather hose to the filler pipe.


Hide 77001U 13.CONNECT FUEL HOSE

a.

Connect the fuel hose.


Hide 14.CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

except G.C.C. Countries:

Connect the 2 fuel tank evaporation vent tubes.


b.

for G.C.C. Countries:

Connect the fuel tank evaporation vent tube.


Hide 77310A 15.INSTALL FUEL TANK CAP ASSEMBLY

Hide 51933A 16.INSTALL NO. 1 SPARE WHEEL STOPPER

a.

Install the spare wheel stopper with the 2 bolts.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 51949B 17.INSTALL SPARE WHEEL CARRIER CROSSMEMBER AND SPARE WHEEL CARRIER BRACKET

a.

Install the spare wheel carrier crossmember and 2 brackets to the vehicle with the 6 bolts labeled C.

Torque:
for bolt C : 20 N*m (204 kgf*cm, 15 ft.*lbf)

A384262E01
4.177,0.365 4.333,0.563 0.156,0.198 10 false A 4.927,0.833 5.083,1.031 0.156,0.198 10 false B 4.896,1.708 5.052,1.906 0.156,0.198 10 false B 2.094,0.875 2.25,1.073 0.156,0.198 10 false B 2.135,1.792 2.292,1.99 0.156,0.198 10 false B 5.802,1.927 5.958,2.125 0.156,0.198 10 false C 6.375,1.896 6.531,2.094 0.156,0.198 10 false C 6.76,1.906 6.917,2.104 0.156,0.198 10 false C 0.281,1.906 0.438,2.104 0.156,0.198 10 false C 0.698,1.896 0.854,2.094 0.156,0.198 10 false C 1.24,1.927 1.396,2.125 0.156,0.198 10 false C


b.

Temporarily install the bolt labeled A, and then tighten the bolt labeled A and bolts labeled B.

Torque:
for bolt A : 29 N*m (296 kgf*cm, 21 ft.*lbf)
for bolt B : 20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 19.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 22.INSTALL SPARE TIRE