Home › Engine / Hybrid System › 1UR-FE (FUEL) › FUEL TANK › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052782 1UR-FE FUEL _0255101 FUEL TANK A

1UR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 77310A 2.REMOVE FUEL TANK CAP ASSEMBLY

Hide 77606 3.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A175014

Remove the 5 bolts and No. 1 fuel tank protector sub-assembly.


Hide 77209C 4.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A310182E01
0.159,2.93 0.345,3.098 0.186,0.167 10 *2 2.239,3.99 2.425,4.158 0.186,0.167 10 *5 1.11,4.09 1.296,4.258 0.186,0.167 10 *4 1.388,2.684 1.574,2.851 0.186,0.167 10 *1 3.046,2.813 3.232,2.980 0.186,0.167 10 *3 1.348,2.773 1.21,2.773 1.21,2.773 0.967,3.206 false 0.368,3.019 0.485,3.019 0.485,3.019 0.534,3.443 false 3.015,2.899 2.915,2.899 2.915,2.899 2.74,3.243 false 1.199,4.053 1.199,3.812 false 2.199,4.07 1.726,4.07 1.726,4.07 1.726,3.676 false 1.91,3.676 1.91,4.07 false 1.598,0.226 1.784,0.394 0.186,0.167 10 *1 1.558,0.315 1.42,0.315 1.42,0.315 1.27,0.452 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank main tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Pipe
*3 Nylon Tube
*4 Connector
*5 O-Ring
V100135

Pull Up


Hide 5.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

A308904E01
3.125,2.492 3.317,2.663 0.192,0.171 10 *1 3.922,3.505 4.114,3.676 0.192,0.171 10 *5 2.931,3.553 3.123,3.724 0.192,0.171 10 *4 4.621,2.52 4.813,2.691 0.192,0.171 10 *3 2.177,2.56 2.368,2.731 0.192,0.171 10 *2 3.606,0.068 3.798,0.239 0.192,0.171 10 *b 0.272,0.068 0.463,0.239 0.192,0.171 10 *a 2.353,2.632 2.482,2.632 2.482,2.632 2.592,3.053 false 3.106,2.569 3.013,2.569 3.013,2.569 2.877,2.853 false 3.001,3.347 3.001,3.534 false 3.699,3.235 3.699,3.581 false 3.55,3.235 3.55,3.581 3.55,3.581 3.874,3.581 false 4.584,2.597 4.491,2.597 4.491,2.597 4.355,2.881 false 2.546,0.372 2.738,0.542 0.192,0.171 10 *1 2.527,0.449 2.433,0.449 2.433,0.449 2.296,0.548 false 5.321,0.351 5.513,0.522 0.192,0.171 10 *1 5.302,0.429 5.208,0.429 5.208,0.429 5.028,0.538 false

Text in Illustration
*1 Retainer *2 Pipe
*3 Nylon Tube *4 Connector
*5 O-Ring - -
*a except G.C.C. Countries *b for G.C.C. Countries
V100135

Pull Up - -

a.

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank main tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 6.DRAIN FUEL

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

CAUTION:
·

Do not smoke or be near an open flame when working on the fuel system.

·

Secure good ventilation.

·

Keep gasoline away from rubber or leather parts.



HINT:
A181470E04
1.583,3.823 1.583,3.698 1.583,3.698 1.865,3.302 true 1.177,0.698 1.354,0.698 1.354,0.698 1.844,0.927 true 0.042,0 0.25,0.208 0.208,0.208 10 false *a 0.063,2.313 0.281,2.521 0.219,0.208 10 false *b 1.521,3.813 1.729,3.99 0.208,0.177 10 false *c 0.99,0.615 1.188,0.792 0.198,0.177 10 true *c

If the fuel pump does not operate, remove the tube joint clip and disconnect the fuel tank return tube sub-assembly, and drain fuel from the port shown in the illustration.


Text in Illustration
*a for Single Tank Type
*b for Double Tank Type
*c Port


f.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




g.
A181387E02
0.069,0 0.280,0.199 0.211,0.199 10 *a 0.075,2.274 0.299,2.479 0.224,0.206 10 *b

Disconnect the fuel pump and fuel sender gauge connector.

Text in Illustration
*a for Single Tank Type
*b for Double Tank Type


Hide 7. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 8.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 71300S 9.REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)

Hide 71400S 10.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)

Hide 11.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 62520P 12.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

Hide 62510P 13.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

Hide 58510D 14.REMOVE FRONT FLOOR CARPET ASSEMBLY

E157065

a.

Turn over the floor carpet.

HINT:

Fold back the floor carpet so that the air duct can be removed.



Hide 58329F 15.REMOVE REAR FLOOR NO. 2 SERVICE HOLE COVER

a.
A181426

w/ Rear Air Conditioning System:

Remove the 2 screws and air duct.


b.
A181427

Remove the rear floor No. 2 service hole cover.


Hide 16.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Single Tank Type)

a.
A310183E01
0.301,2.874 0.487,3.042 0.186,0.167 10 *2 1.982,3.969 2.168,4.137 0.186,0.167 10 *5 0.853,4.055 1.039,4.222 0.186,0.167 10 *4 1.372,2.663 1.558,2.830 0.186,0.167 10 *1 2.789,2.777 2.975,2.945 0.186,0.167 10 *3 1.332,2.752 1.194,2.752 1.194,2.752 0.951,3.172 false 0.51,2.963 0.628,2.963 0.628,2.963 0.677,3.387 false 2.758,2.863 2.658,2.863 2.658,2.863 2.483,3.207 false 0.942,4.018 0.942,3.777 false 1.941,4.049 1.469,4.049 1.469,4.049 1.469,3.655 false 1.604,3.655 1.604,4.049 false 1.19,0.205 1.376,0.373 0.186,0.167 10 *1 1.15,0.294 1.013,0.294 1.013,0.294 0.862,0.431 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the No. 2 fuel tank breather tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Pipe
*3 Nylon Tube
*4 Connector
*5 O-Ring
V100135

Pull Up


Hide 17.DISCONNECT NO. 2 FUEL TANK BREATHER HOSE (for Double Tank Type)

a.
A308892

for G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Slide the clip and disconnect the No. 2 fuel tank breather hose from the pipe.



Hide 77204A 18.DISCONNECT FUEL TANK RETURN TUBE (for Single Tank Type)

a.
A310184E01
0.302,3.008 0.488,3.175 0.186,0.167 10 *2 2.104,4.068 2.290,4.235 0.186,0.167 10 *5 0.975,4.153 1.161,4.321 0.186,0.167 10 *4 1.482,2.752 1.668,2.919 0.186,0.167 10 *1 2.912,2.881 3.098,3.048 0.186,0.167 10 *3 1.442,2.841 1.304,2.841 1.304,2.841 1.061,3.274 false 0.511,3.097 0.628,3.097 0.628,3.097 0.677,3.521 false 2.88,2.967 2.78,2.967 2.78,2.967 2.605,3.311 false 1.064,4.116 1.064,3.875 false 2.064,4.148 1.591,4.148 1.591,4.148 1.591,3.754 false 1.726,3.754 1.726,4.148 false 2.121,0.216 2.307,0.383 0.186,0.167 10 *1 2.081,0.305 1.943,0.305 1.943,0.305 1.793,0.442 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank return tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Pipe
*3 Nylon Tube
*4 Connector
*5 O-Ring
V100135

Pull Up


Hide 19.DISCONNECT FUEL TANK RETURN TUBE (for Double Tank Type)

A308905E01
3.078,2.482 3.257,2.654 0.179,0.172 10 *1 4.624,2.575 4.803,2.747 0.179,0.172 10 *3 2.151,2.551 2.330,2.723 0.179,0.172 10 *2 3.942,3.444 4.121,3.616 0.179,0.172 10 *5 2.941,3.556 3.120,3.728 0.179,0.172 10 *4 0.276,0.072 0.455,0.244 0.179,0.172 10 *a 3.624,0.072 3.803,0.244 0.179,0.172 10 *b 2.337,2.62 2.449,2.62 2.449,2.62 2.596,3.036 false 3.041,2.553 2.925,2.553 2.925,2.553 2.862,2.851 false 4.585,2.648 4.494,2.648 4.494,2.648 4.41,2.881 false 3.699,3.234 3.699,3.503 false 3.913,3.503 3.55,3.503 3.55,3.503 3.55,3.234 false 3.006,3.346 3.006,3.54 false 2.524,0.321 2.704,0.493 0.179,0.172 10 *1 2.487,0.392 2.372,0.392 2.372,0.392 2.248,0.498 false 5.302,0.202 5.481,0.374 0.179,0.172 10 *1 5.265,0.273 5.149,0.273 5.149,0.273 5.025,0.376 false

Text in Illustration
*1 Retainer *2 Pipe
*3 Nylon Tube *4 Connector
*5 O-Ring - -
*a except G.C.C. Countries *b for G.C.C. Countries
V100135

Pull Up - -

a.

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank return tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 77027B 20.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A308891E01
1.825,0.121 2.013,0.305 0.188,0.184 10 *1 1.862,4.016 2.051,4.199 0.188,0.184 10 *5 0.962,4.186 1.150,4.369 0.188,0.184 10 *4 2.574,3.042 2.762,3.226 0.188,0.184 10 *3 0.185,3.005 0.373,3.188 0.188,0.184 10 *2 1.233,2.967 1.421,3.151 0.188,0.184 10 *1 0.397,3.096 0.5,3.096 0.5,3.096 0.629,3.572 false 1.199,3.059 1.093,3.059 1.093,3.059 0.961,3.346 false 1.044,3.918 1.044,4.165 false 2.562,3.125 2.446,3.125 2.446,3.125 2.353,3.38 false 1.601,3.802 1.601,4.099 false 1.812,4.099 1.474,4.099 1.474,4.099 1.474,3.802 false 1.783,0.217 1.677,0.217 1.677,0.217 1.49,0.392 false

for G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Pull up the retainer and disconnect the No. 1 fuel emission tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Pipe
*3 Nylon Tube
*4 Connector
*5 O-Ring
V100135

Pull Up



b.
A310181E01
2.85,0.245 3.041,0.414 0.191,0.170 10 *1 0.225,2.728 0.415,2.898 0.191,0.170 10 *4 1.329,2.72 1.520,2.889 0.191,0.170 10 *3 0.994,4.151 1.185,4.320 0.191,0.170 10 *2 2.756,2.845 2.946,3.015 0.191,0.170 10 *5 2.816,0.326 2.696,0.326 2.696,0.326 2.524,0.569 false 2.717,2.939 2.541,2.939 2.541,2.939 2.351,3.189 false 1.093,3.746 1.093,4.138 false 0.771,3.309 0.608,2.822 0.608,2.822 0.453,2.822 false 1.303,2.81 1.097,2.81 1.097,2.81 1.097,3.202 false

except G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Pull the retainer up while pinching it on both sides by hand as shown in the illustration, and disconnect the No. 1 fuel emission tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Connector
*3 O-Ring
*4 Pipe
*5 Nylon Tube
V100135

Push
V100136

Pull Up



Hide 77259E 21.DISCONNECT FUEL HOSE (for Double Tank Type)

a.
A308893

for G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Slide the clip and disconnect the fuel hose from the pipe.



Hide 77252A 22.DISCONNECT NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

A308906E03
3.688,3.188 4.021,3.188 false 4.021,3.188 4.021,3.5 false 3.688,3.292 4.021,3.292 false 3.073,3.156 3.167,3.156 3.167,3.156 3.25,3.406 false 3.354,2.5 3.542,2.5 3.542,2.5 3.594,2.698 false 3.74,2.833 3.958,2.698 3.958,2.698 4.063,2.698 true 3.792,2.948 4.073,2.948 false 1.167,0.792 1.396,0.656 1.396,0.656 1.5,0.656 false 4.365,0.51 4.594,0.375 4.594,0.375 4.698,0.375 false 4.094,2.615 4.292,2.792 0.198,0.177 10 false *1 4.094,2.865 4.292,3.042 0.198,0.177 10 false *2 3.958,3.51 4.156,3.688 0.198,0.177 10 false *3 3.156,2.438 3.354,2.615 0.198,0.177 10 false *4 2.896,3.083 3.094,3.26 0.198,0.177 10 false *5 0.271,0.073 0.469,0.25 0.198,0.177 10 false *a 3.615,0.073 3.813,0.25 0.198,0.177 10 false *b 1.521,0.583 1.719,0.76 0.198,0.177 10 false *1 4.729,0.302 4.927,0.479 0.198,0.177 10 false *1

Text in Illustration
*1 Retainer *2 Connector
*3 O-Ring *4 Pipe
*5 Nylon Tube - -
*a except G.C.C. Countries *b for G.C.C. Countries
V100135

Pull Up - -

a.

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the No. 2 fuel tank main tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 23.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE (for Double Tank Type)

a.
A310185E01
2.777,0.2 2.978,0.387 0.201,0.187 10 *1 2.751,0.298 2.615,0.298 2.615,0.298 2.399,0.474 false 0.96,3.493 1.150,3.670 0.191,0.177 10 *5 2.59,3.884 2.781,4.061 0.191,0.177 10 *3 2.528,3.265 2.719,3.442 0.191,0.177 10 *2 1.437,2.788 1.627,2.965 0.191,0.177 10 *4 2.528,2.947 2.719,3.124 0.191,0.177 10 *1 1.651,2.87 1.849,2.87 1.849,2.87 1.997,3.115 false 2.498,3.351 2.252,3.351 false 2.498,3.042 2.408,3.042 2.408,3.042 2.142,3.264 false 2.119,3.605 2.674,3.605 false 2.674,3.605 2.674,3.847 false 2.119,3.744 2.674,3.744 false 1.205,3.579 1.333,3.579 1.333,3.579 1.445,3.883 false

except G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Pull up the retainer and disconnect the No. 2 fuel tank breather tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Connector
*3 O-Ring
*4 Pipe
*5 Nylon Tube
V100135

Pull Up



Hide 24.DISCONNECT FUEL TANK BREATHER TUBE (for Single Tank Type)

a.
A310186E01
1.8,2.165 1.993,2.341 0.193,0.176 10 *1 1.778,2.258 1.632,2.258 1.632,2.258 1.452,2.437 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank breather tube from the fuel tank to filler pipe sub-assembly.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.



Text in Illustration
*1 Retainer
V100135

Pull Up


Hide 25.DISCONNECT FUEL TANK BREATHER TUBE (for Double Tank Type)

a.
A310187E01
1.648,2.217 1.853,2.404 0.205,0.187 10 *1 1.609,2.298 1.463,2.298 1.463,2.298 1.23,2.489 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank breather tube from the fuel tank to filler pipe sub-assembly.

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.



Text in Illustration
*1 Retainer
V100135

Pull Up


Hide 26.DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Single Tank Type)

a.
A176314

Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank to filler pipe sub-assembly.


Hide 27.DISCONNECT FUEL TANK TO FILLER PIPE HOSE (for Double Tank Type)

a.
A175067

Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank to filler pipe sub-assembly.


Hide 77100U 28.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place an engine lifter under the fuel tank sub-assembly.


b.
A175024

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank band sub-assemblies.


c.

Slowly lower the engine lifter slightly.


Hide 29.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE SUB-ASSEMBLY (for Single Tank Type)

a.
A181471E03
2.007,3.974 2.201,4.139 0.194,0.165 10 *4 2.345,3.377 2.533,3.542 0.189,0.165 10 *3 0.528,3.85 0.716,4.027 0.188,0.177 10 *2 0.831,2.371 1.037,2.537 0.206,0.165 10 *1 1.045,2.467 1.182,2.467 1.182,2.467 1.372,2.846 false 0.606,3.824 0.606,3.698 0.606,3.698 1.167,3.347 false 1.966,4.056 1.85,4.056 1.85,4.056 1.713,3.879 false 1.748,3.465 2.302,3.465 false 1.746,3.605 2.154,3.605 2.154,3.605 2.154,3.471 false

Remove the 2 tube joint clips and pull out the 2 fuel tube joints.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.



Text in Illustration
*1 Fuel Tube Joint
*2 Tube Joint Clip
*3 O-Ring
*4 Fuel Suction Plate Sub-assembly


b.
A310188E01
1.212,0.171 1.45,0.445 0.238,0.275 2.334,0.087 2.527,0.264 0.192,0.177 10 *2 1.232,0.191 1.424,0.367 0.192,0.177 10 *1 1.449,0.282 1.553,0.282 1.553,0.282 1.713,0.518 false 1.833,0.607 2.161,0.178 2.161,0.178 2.286,0.178 false

Detach the clamp and remove the fuel tank main tube sub-assembly.

Text in Illustration
*1 Fuel Tank Main Tube Sub-assembly
*2 Fuel Tank Return Tube Sub-assembly


c.

Detach the clamp and remove the fuel tank return tube sub-assembly.


Hide 77259E 30.REMOVE FUEL HOSE (for Double Tank Type)

a.
A308896

for G.C.C. Countries:

Slide the clip and remove the fuel hose from the fuel suction tube sub-assembly.


Hide 31.REMOVE FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY (for Double Tank Type)

a.
A176319E05
2.585,4.05 2.778,4.229 0.193,0.179 10 *4 2.429,3.324 2.644,3.503 0.215,0.179 10 *3 0.678,3.807 0.890,4.005 0.212,0.198 10 *2 0.988,2.238 1.163,2.420 0.175,0.182 10 *1 1.189,2.325 1.326,2.325 1.326,2.325 1.516,2.884 false 0.781,3.786 0.781,3.659 0.781,3.659 1.342,3.309 false 1.833,3.412 2.387,3.412 false 1.831,3.527 2.239,3.527 2.239,3.527 2.239,3.418 false 2.702,4.023 2.702,3.904 2.702,3.904 1.915,3.744 false

Remove the 3 tube joint clips and pull out the 3 fuel tube joints.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.



Text in Illustration
*1 Fuel Tube Joint
*2 Tube Joint Clip
*3 O-Ring
*4 Fuel Suction Plate Sub-assembly


b.
A310189E02
1.677,0.531 1.333,0.531 true 1.844,0.615 2.063,0.115 2.063,0.115 2.177,0.115 true 2.688,0.885 3.031,0.531 3.031,0.531 3.125,0.531 true 1.156,0.427 1.365,0.604 0.208,0.177 10 true *1 3.156,0.448 3.365,0.625 0.208,0.177 10 false *3 2.229,0.042 2.438,0.219 0.208,0.177 10 false *2

except G.C.C. Countries:

i.

Detach the clamp and remove the fuel tank main tube sub-assembly.

Text in Illustration
*1 Fuel Tank Main Tube Sub-assembly
*2 Fuel Tank Return Tube Sub-assembly
*3 No. 2 Fuel Tank Main Tube Sub-assembly


ii.

Detach the clamp and remove the fuel tank return tube sub-assembly.


iii.

Detach the 2 clamps and remove the No. 2 fuel tank main tube sub-assembly.



c.
A308897E02
0.958,0.302 0.625,0.302 true 1.646,0.146 1.49,0.146 1.49,0.146 1.146,0.354 true 2.292,0.698 2.396,0.531 2.396,0.531 2.479,0.531 false 1.667,0.052 1.854,0.219 0.188,0.167 10 true *2 2.49,0.448 2.677,0.615 0.188,0.167 10 false *3 0.417,0.219 0.604,0.385 0.188,0.167 10 true *1

for G.C.C. Countries:

i.

Detach the clamp and remove the fuel tank main tube sub-assembly.

Text in Illustration
*1 Fuel Tank Main Tube Sub-assembly
*2 Fuel Tank Return Tube Sub-assembly
*3 No. 2 Fuel Tank Main Tube Sub-assembly


ii.

Detach the clamp and remove the fuel tank return tube sub-assembly.


iii.

Detach the 2 clamps and remove the No. 2 fuel tank main tube sub-assembly.



Hide 77020A 32.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77213B 33.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A176316

Loosen the hose clamp and remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.


Hide 77697 34.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
U163755E02
1.771,0.167 1.969,0.354 0.198,0.188 10 false *a 1.677,3.323 1.802,3.49 0.125,0.167 10 false 2 0.729,3.313 0.854,3.479 0.125,0.167 10 false 1 2.625,3.323 2.75,3.49 0.125,0.167 10 false 3

Remove the fuel tube clamp from the No. 1 fuel tank heat insulator.

Text in Illustration
*a for G.C.C. Countries


b.

Using needle-nose pliers, remove the 4 clips shown in the illustration, and then remove the No. 1 fuel tank heat insulator.