Home › Engine / Hybrid System › 1UR-FE (FUEL) › FUEL INJECTOR › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052782 1UR-FE FUEL _0255097 FUEL INJECTOR A

1UR-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.




b.

Start the engine. After the engine stops, turn the engine switch off.

HINT:

DTC P0171/0174 (system too lean) may be stored.



c.

Crank the engine again, and then check that the engine does not start.


d.

Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.


e.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 5.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 6.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 25710 10.REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 23902 13.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A218691

Disconnect the No. 2 fuel tube from the fuel pressure regulator (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 23901 14.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A218692

Disconnect the fuel tube from the fuel delivery pipe (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.
A218693

Disconnect the fuel tube from the No. 2 fuel delivery pipe (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 15.DISCONNECT WIRE HARNESS AND HOSE

a.
A218650

Disconnect the purge VSV connector.


b.

Disconnect the purge line hose from the purge VSV.


c.

Disconnect the vacuum switching valve connector (for ACIS).


Hide 23271F 16.DISCONNECT FUEL HOSE

a.
A218694

Detach the clamp.


b.

Disconnect the fuel hose from the No. 2 fuel delivery pipe (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


Hide 23807 17.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A218695

Disconnect the No. 6 wire harness connector.


b.

Remove the 2 bolts and fuel delivery pipe.

NOTICE:

When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.



c.

Remove the 2 delivery pipe spacers and 4 insulators from the intake manifold.


Hide 23808 18.REMOVE NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A218696

Disconnect the No. 7 wire harness connector.


b.

Remove the 2 bolts and No. 2 fuel delivery pipe.

NOTICE:

When removing the delivery pipe, hold the pipe by both ends and pull it straight upward.



c.

Remove the 2 delivery pipe spacers and 4 insulators from the intake manifold.


Hide 23250 19.REMOVE FUEL INJECTOR ASSEMBLY

a.
A218720

Remove the fuel injector from the fuel delivery pipe, and then disconnect the injector connector.

NOTICE:
A384270E01
2.021,0.406 2.333,0.604 0.313,0.198 10 false *1

For reinstallation, attach a tag or label to the injector shaft.


Text in Illustration
*1 No. 1


b.
A149190E05
2.772,1.742 2.939,1.904 0.168,0.162 10 *1 2.852,1.468 2.852,1.718 false

Remove the O-ring from the fuel injector.

Text in Illustration
*1 O-ring


c.
A218721

Detach the 3 clamps and then remove the No. 6 wire harness from the fuel delivery pipe.


d.
A214318

Detach the 3 clamps and then remove the No. 7 wire harness from the No. 2 fuel delivery pipe.