When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head, or intake manifold, it is necessary to replace the injection pipes with new ones.
w/ DPF:
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53806
3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405A
5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53292A
6.REMOVE UPPER RADIATOR SUPPORT SEAL
7.DRAIN ENGINE COOLANT
17940D
8.REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
17705
9.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
Loosen the hose clamp.
Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.
Detach the 4 clamps and remove the air cleaner cap.
17881
10.REMOVE NO. 1 AIR CLEANER HOSE
Loosen the hose clamp and remove the No. 1 air cleaner hose.
17861
11.REMOVE INTAKE AIR CONNECTOR
w/ Viscous Heater:
Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.
| *A | w/ Viscous Heater |
w/o Viscous Heater:
Disconnect the connector from the water temperature sensor.
Using a clip remover, detach the 3 wire harness clamps.
Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.
17973
12.REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)
Loosen the No. 1 air hose clamp.
Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.
Remove the 3 nuts, bolt and No. 1 cool air inlet.
Remove the gasket from the air tube RH.
17973
13.REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)
Loosen the No. 2 air hose clamp.
Remove the 3 nuts, bolt and No. 2 cool air inlet.
Remove the gasket from the air tube LH.
14.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
Disconnect the wire harness clamp from the No. 2 engine oil level dipstick guide.
Disconnect the ventilation hose from the cylinder head cover RH.
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 2 bolts and No. 2 engine oil level dipstick guide.
Remove the O-ring from the No. 2 engine oil level dipstick guide.
17971
15.REMOVE AIR TUBE SUB-ASSEMBLY RH
16.REMOVE DIESEL THROTTLE BODY ASSEMBLY RH
17.DRAIN CLUTCH FLUID (for Manual Transmission)
31418
18.REMOVE CLUTCH HOSE (for Manual Transmission)
17972
19.REMOVE AIR TUBE SUB-ASSEMBLY LH
31489
20.REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)
23265
21.REMOVE NO. 1 GAS FILTER
17947B
22.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET
26100G
23.REMOVE DIESEL THROTTLE BODY ASSEMBLY LH
17341F
24.REMOVE NO. 1 AIR HOSE
Loosen the hose clamp and remove the No. 1 air hose.
17363K
25.REMOVE NO. 3 AIR TUBE
Disconnect the wire harness from the clamp.
Remove the nut and ground wire.
Remove the bolt and disconnect the wire harness bracket.
Loosen the hose clamp and remove the bolt and No. 3 air tube.
17342D
26.REMOVE NO. 2 AIR HOSE
Loosen the hose clamp and remove the No. 2 air hose.
17364
27.REMOVE NO. 4 AIR TUBE
Remove the bolt and disconnect the suction hose.
Loosen the hose clamp and remove the bolt and No. 4 air tube.
17806
28.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY
Disconnect the ventilation hose from the oil separator.
Loosen the hose clamp.
Remove the bolt and No. 2 air cleaner pipe.
87209
29.DISCONNECT WATER HOSE SUB-ASSEMBLY
| *A | w/ Rear Heater |
| *B | w/o Rear Heater |
87208
30.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
Remove the 4 bolts and disconnect the 4 water hose ends, and then remove the heater water pipe.
17885
31.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY
Loosen the hose clamp.
Remove the bolt and No. 1 air cleaner pipe.
23274D
32.DISCONNECT FUEL HOSE
w/ DPF:
| *a | for Fuel Filter with Heater |
| *b | for Fuel Filter without Heater |
w/o DPF:
| *a | for Fuel Filter with Heater |
| *b | for Fuel Filter without Heater |
16268M
33.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)
Remove the 2 bolts and disconnect the 2 water hose ends, and then remove the No. 3 water by-pass pipe.
16288
34.REMOVE NO. 4 WATER BY-PASS PIPE
w/ EGR System:
Remove the 2 bolts and nut.
| *A | w/ DPF | *B | w/o DPF |
w/ DPF:
Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.
w/o DPF:
Disconnect the 4 water hose ends, and then remove the No. 4 water by-pass pipe.
w/o EGR System:
Remove the 2 bolts and nut.
Disconnect the 3 water hose ends, and then remove the No. 4 water by-pass pipe.
35.DISCONNECT ENGINE WIRE
LH Side:
Disconnect the 4 connectors.
Using a clip remover, detach the 3 wire harness clamps.
Disconnect the 2 connectors.
Using a clip remover, detach the 3 wire harness clamps.
Disconnect the 8 connectors.
| *A | w/ DPF | *B | w/o DPF |
Remove the bolt and engine wire harness bracket labeled B.
Using a clip remover, detach the wire harness clamp labeled D.
Remove the 2 bolts and disconnect the engine wire protector labeled A.
for RHD:
Disconnect the wire harness from the wire harness clamp holder labeled C.
RH Side:
Disconnect the 7 connectors.
| *A | w/ DPF | *B | w/o DPF |
Using a clip remover, detach the wire harness clamp.
Remove the 3 bolts and disconnect the wire harness protector labeled A.
Remove the bolt and wire harness bracket labeled B.
Remove the screw grommet, nut and glow plug wire harness labeled C.
for RHD:
Disconnect the wire harness from the wire harness clamp holder.
| *A | w/ DPF |
| *B | w/o DPF |
for RHD:
Remove the bolt and wire harness clamp holder.
Rear Side:
Using a clip remover, detach the wire harness clamp.
| *A | w/ DPF |
| *B | w/o DPF |
Remove the 2 bolts and 2 ground wires labeled C.
Remove the 2 bolts and disconnect the engine wire harness protector labeled B.
w/ DPF:
Disconnect the 3 connectors.
w/o DPF:
Disconnect the connector.
Remove the screw grommet, nut and disconnect the glow plug wire harness labeled A.
23802E
36.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)
After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel pipe ends, cover the fuel pipe ends with plastic bags.
After removing a fuel pipe, to prevent dirt or foreign objects from entering the fuel supply pump hole, cover the hole with protective tape.
Disconnect the fuel hose from the No. 5 nozzle leakage pipe.
Remove the bolt and No. 2 injection pipe clamp.
Remove the union bolt and gasket.
Remove the bolt, nut and No. 2 fuel pipe.
23706
37.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes, cover the holes with protective tape.
w/ EGR System:
Using a union nut wrench, loosen the No. 6 injection pipe ends.
Remove the 2 nuts and 2 No. 2 injection pipe clamps.
Remove the No. 6 injection pipe.
w/o EGR System:
Using a union nut wrench, loosen the No. 6 injection pipe ends.
Remove the nut and No. 2 injection pipe clamp.
Remove the bolt and No. 6 injection pipe.
25860
38.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)
25706
39.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)
11225
40.REMOVE CYLINDER HEAD COVER SILENCER LH (w/ DPF)
23764A
41.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)
Disconnect the fuel hose.
Remove the fuel check valve, No. 4 nozzle leakage pipe and gasket.
23701
42.REMOVE INJECTION PIPE LH
w/ Intercooler:
Remove the 2 nuts and 4 injection pipe clamps.
| *A | w/ DPF |
| *B | w/o DPF |
Using a union nut wrench, remove the 4 injection pipes.
| *A | w/ DPF |
| *B | w/o DPF |
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.
23812D
43.REMOVE NO. 2 FUEL PIPE (w/ DPF)
23765
44.REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)
23820A
45.REMOVE COMMON RAIL ASSEMBLY LH
23801L
46.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
w/ DPF:
Remove the bolt and No. 2 injection pipe clamp.
Disconnect the fuel hose.
Remove the union bolt, nut, bolt, fuel filter to injection pump fuel pipe and gasket.
w/o DPF:
Disconnect the 2 hoses from the fuel pipe.
Remove the bolt and fuel filter to injection pump fuel pipe.
23243C
47.DISCONNECT FUEL PUMP MOTOR WIRE
Remove the bolt and disconnect the connector from the fuel supply pump.
23705
48.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY
Using a union nut wrench, remove the No. 5 injection pipe.
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail hole or injection pump hole, cover the holes with protective tape.
11224
49.REMOVE CYLINDER HEAD COVER SILENCER RH (w/ DPF)
23712
50.REMOVE NO. 2 FUEL INJECTOR PROTECTOR (w/ DPF)
23711
51.REMOVE NO. 1 FUEL INJECTOR PROTECTOR (w/ DPF)
23702
52.REMOVE INJECTION PIPE RH
w/ Intercooler:
Remove the 2 nuts and 4 injection pipe clamps.
| *A | w/ DPF |
| *B | w/o DPF |
Using a union nut wrench, remove the 4 injection pipes.
| *A | w/ DPF |
| *B | w/o DPF |
After removing an injection pipe, to prevent dirt or foreign objects from entering the common rail holes or injector holes, cover the holes with protective tape.
23810A
53.REMOVE COMMON RAIL ASSEMBLY RH
27148B
54.REMOVE CONNECTING WIRE (w/ DPF)
Detach the 2 clamps and remove the connecting wire.
23763
55.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)
Remove the 2 injector hollow screws, 3 bolts, No. 3 nozzle leakage pipe and 2 gaskets.
23762B
56.REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)
23761A
57.REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)
17135A
58.REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)
17136
59.REMOVE NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)
17113
60.REMOVE INTAKE PIPE
w/ EGR System:
Remove the 2 nuts, 6 bolts, intake pipe and 2 gaskets.
w/o EGR System:
Remove the 2 nuts, 4 bolts, intake pipe and gasket.
61.DISCONNECT NO. 2 ENGINE WIRE
Remove the 3 bolts and using a clip remover, detach the 2 wire harness clamps, and then disconnect the No. 2 engine wire.
17114D
62.REMOVE NO. 3 INTAKE MANIFOLD
Remove the 16 bolts, No. 3 intake manifold and 2 gaskets.
17853B
63.REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR System)
25615A
64.REMOVE EGR PIPE INSULATOR (w/ EGR System)
Remove the 2 bolts and EGR pipe insulator.
25620
65.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)
Remove the 10 bolts, EGR valve with EGR cooler and 2 gaskets.
Disconnect the No. 5 water by-pass hose from the water by-pass outlet.
25689
66.REMOVE EGR COOLER INSULATOR (w/ EGR System)
23763
67.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)
Disconnect the No. 1 fuel hose from the fuel cooler.
Remove the union bolt, bolt, No. 3 nozzle leakage pipe and gasket.
After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.
23764A
68.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)
Disconnect the No. 2 fuel hose from the fuel cooler.
Remove the union bolt, bolt, No. 4 nozzle leakage pipe and gasket.
After removing the nozzle leakage pipe, to prevent dirt or foreign objects from entering the nozzle leakage pipe, cover the nozzle leakage pipe ends with plastic bags.
16283
69.DISCONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)
23920A
70.REMOVE FUEL COOLER ASSEMBLY (w/o DPF)
23901H
71.REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)
Disconnect the 3 fuel tube connectors (See page Engine / Hybrid System>1VD-FTV (FUEL)>FUEL SYSTEM(w/ DPF)>PRECAUTION).
Detach the 3 clamps and remove the fuel tube.
16268
72.REMOVE NO. 1 WATER BY-PASS PIPE
Remove the union bolt, bolt, No. 1 water by-pass pipe and gasket.
| *A | w/ DPF |
| *B | w/o DPF |
23881D
73.REMOVE FUEL HOSE BRACKET (w/ DPF)
Remove the bolt and fuel hose bracket.
23841C
74.REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)
Remove the 2 bolts and 2 No. 1 fuel pipe clamps.
| *a | RH Side |
| *b | LH Side |
17111
75.REMOVE NO. 1 INTAKE MANIFOLD
Remove the 9 bolts, No. 1 intake manifold and gasket.
17112
76.REMOVE NO. 2 INTAKE MANIFOLD
Remove the 9 bolts, No. 2 intake manifold and gasket.
77.REPLACE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
For Intake Pipe:
Using an E8 "TORX" wrench, replace the stud bolts.
For No. 3 Intake Manifold:
Using an E8 "TORX" wrench, replace the stud bolts labeled A.
Using an E6 "TORX" wrench, replace the stud bolts labeled B.
Using an E6 "TORX" wrench, replace the stud bolt labeled C.
78.REPLACE RING PIN
It is not necessary to remove a ring pin unless it is being replaced.
For No. 1 and No. 2 Intake Manifold:
Replace the ring pins.
4.4 to 5.6 mm (0.173 to 0.222 in.)
| *1 | Protrusion height |