1.REMOVE ENGINE ASSEMBLY
17361
2.REMOVE AIR TUBE (w/ Secondary Air Injection System)
25701B
3.REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
25702B
4.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
19500
5.REMOVE IGNITION COIL ASSEMBLY
11452
6.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the engine oil level dipstick.
Remove the bolt and engine oil level dipstick guide.
Remove the O-ring from the engine oil level dipstick guide.
16323
7.REMOVE WATER INLET HOUSING
16206
8.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the 2 hoses.
Remove the 3 bolts and water by-pass pipe.
16603
9.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley.
16604
10.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
16620
11.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 5 bolts and V-ribbed belt tensioner.
12.REMOVE OIL FILTER ELEMENT
15671
13.REMOVE OIL FILTER BRACKET
Remove the 2 nuts, bolt, oil filter bracket and gasket.
13471
14.REMOVE CRANKSHAFT PULLEY
Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.
Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.
15771
15.REMOVE NO. 1 OIL PIPE
Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.
Do not touch the mesh when removing the oil control valve filter.
15772
16.REMOVE NO. 2 OIL PIPE
Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.
Do not touch the mesh when removing the oil control valve filter.
17.DISCONNECT FUEL PIPE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the fuel pipe.
11202
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
11201
19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 12 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 3 gaskets.
12102A
20.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 10 bolts and 2 nuts.
Make sure the removed parts are returned to the same places they were removed from.
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
| *1 | Oil Pan Seal Cutter |
Be careful not to damage the contact surfaces of the oil pans.
15104
21.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 nuts and oil strainer.
12101
22.REMOVE OIL PAN SUB-ASSEMBLY
Remove the 17 bolts and 2 nuts.
Make sure the removed parts are returned to the same places they were removed from.
Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
| *a | LH Side |
| *b | RH Side |
| *c | Pry |
Be careful not to damage the contact surfaces of the cylinder block and oil pan.
Tape the screwdriver tip before use.
Remove the 3 O-rings from the timing chain cover.
11302
23.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 26 bolts and 2 nuts.
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.
Tape the screwdriver tip before use.
Remove the oil pump gasket from the cylinder block.
11301C
24.REMOVE FRONT CRANKSHAFT OIL SEAL
Using a screwdriver and wooden block, pry out the oil seal.
Do not damage the surface of the oil seal press fit hole.
Tape the screwdriver tip before use.