Home › Engine / Hybrid System › 1VD-FTV (LUBRICATION) › OIL PUMP › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052799 1VD-FTV LUBRICATION _0255224 OIL PUMP A

1VD-FTV LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing an injector (including interchanging injectors between cylinders) or common rail, replace the corresponding injection pipes with new ones.

·

w/DPF

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

Hide 15100 1.INSTALL OIL PUMP ASSEMBLY

a.

Install the oil pump with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11381 3.INSTALL REAR ENGINE OIL SEAL RETAINER

NOTICE:

When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.

A158674E01
0.191,0.125 1.166,0.288 0.975,0.163 10 Cylinder Block: 4.058,0.125 5.977,0.295 1.920,0.170 10 Rear Engine Oil Seal Retainer:


a.
A164338E05
0.833,0.875 0.635,0.26 0.635,0.26 0.844,0.26 true 2.771,1.51 2.885,1.667 0.115,0.156 10 false a 3.292,1.5 3.406,1.656 0.115,0.156 10 false a 1.823,2.75 2.063,2.896 0.24,0.146 10 false a-a 2.135,1.917 2.875,2.729 0.74,0.813 10 false 2.0 mm (0.0787 in.) 0.677,1.938 1.438,2.792 0.76,0.854 10 false 2.5 mm (0.0984 in.) 0.917,0.167 2.781,0.344 1.865,0.177 10 false Seal Diameter: 3.0 to 5.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal diameter:

3.0 to 5.0 mm (0.118 to 0.197 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the rear engine oil seal retainer within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




b.

Apply engine oil to the oil seal lip.


c.

Make sure that the lip of the oil seal is properly installed.


d.
U163130E02
1.417,0.271 1.573,0.438 0.156,0.167 10 false 1 2.229,1.667 2.406,1.833 0.177,0.167 10 false 10 1.979,0.271 2.135,0.438 0.156,0.167 10 false 2 0.563,0.438 0.719,0.604 0.156,0.167 10 false 3 2.833,0.438 2.99,0.604 0.156,0.167 10 false 4 0.115,0.917 0.271,1.083 0.156,0.167 10 false 5 3.198,0.792 3.354,0.958 0.156,0.167 10 false 6 0.229,1.75 0.385,1.917 0.156,0.167 10 false 7 3.208,1.646 3.365,1.813 0.156,0.167 10 false 8 0.833,1.917 0.99,2.083 0.156,0.167 10 false 9

Install and uniformly tighten the 10 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.




Hide 15310H 4.INSTALL OIL REGULATOR ASSEMBLY

a.

Install the oil regulator with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 5.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

NOTICE:

When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.


A177348

a.

Install the cylinder block oil hole gasket.


b.

Apply a light coat of engine oil to 3 new O-rings and set the 3 O-rings to the oil regulator and scavenging pump.


c.
A177350E03
2.833,3.781 2.469,4.177 2.469,4.177 2.333,4.177 true 0.917,3.49 2.083,3.677 1.167,0.188 10 false 8.5 mm (0.335 in.) 2.094,1.281 2.198,1.448 0.104,0.167 10 false a 2.604,1.281 2.708,1.448 0.104,0.167 10 false a 0.479,4.083 2.323,4.229 1.844,0.146 10 false Seal Diameter: 3.5 to 4.0 mm 2.573,3.313 2.813,3.469 0.24,0.156 10 false a-a

Apply seal packing to the No. 1 oil pan as shown in the illustration.

Standard seal diameter:

3.5 to 4.0 mm (0.134 to 0.157 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

For the 3 bolt holes labeled with arrows, apply the seal packing on the outer edges. For the other bolt holes, apply the seal packing on the inner edges.

·

Make sure to apply a continuous bead of seal packing as shown in the illustration. If the bead breaks, overlap 3 mm (0.118 in.) of seal packing and continue the bead.

·

Remove any oil and old seal packing from the contact surface.

·

Install the No. 1 oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing.




d.
U162997E02
0.448,0.167 0.802,0.167 0.802,0.167 0.698,0.729 true 0.208,2.646 0.208,2.49 0.208,2.49 0.698,2.083 true 2.063,3.146 2.25,3.146 2.25,3.146 2.604,2.656 true 0.375,0.781 0.531,0.948 0.156,0.167 10 false A 0.333,1.177 0.49,1.344 0.156,0.167 10 false A 0.333,1.5 0.49,1.667 0.156,0.167 10 false A 0.333,1.844 0.49,2.021 0.156,0.177 10 false A 0.948,0.75 1.104,0.917 0.156,0.167 10 false B 1.229,0.75 1.385,0.917 0.156,0.167 10 false B 1.656,0.75 1.813,0.917 0.156,0.167 10 false B 0.896,1.938 1.052,2.104 0.156,0.167 10 false B 1.365,1.938 1.521,2.104 0.156,0.167 10 false B 1.729,1.938 1.885,2.104 0.156,0.167 10 false B 1.99,0.75 2.146,0.917 0.156,0.167 10 false B 2.698,0.469 2.854,0.635 0.156,0.167 10 false C 2.958,0.583 3.115,0.75 0.156,0.167 10 false C 2.948,1.104 3.104,1.271 0.156,0.167 10 false C 2.948,1.552 3.104,1.719 0.156,0.167 10 false C 2.948,1.917 3.104,2.094 0.156,0.177 10 false C 2.365,0.469 2.521,0.635 0.156,0.167 10 false B 2.104,1.948 2.26,2.115 0.156,0.167 10 false A 2.729,2.281 2.885,2.448 0.156,0.167 10 false A 2.323,2.271 2.479,2.438 0.156,0.167 10 false A 0.125,0.063 0.385,0.208 0.26,0.146 10 false Nut 0.063,2.667 0.323,2.813 0.26,0.146 10 false Nut 0.854,3.073 2.01,3.219 1.156,0.146 10 false Oil Reflector Plate

Install the No. 1 oil pan and oil reflector plate with the 20 bolts and 2 nuts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

Bolt Length
Item Quantity Length
Bolt A 7 70 mm (2.76 in.)
Bolt B 8 20 mm (0.787 in.)
Bolt C 5 30 mm (1.18 in.)


Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new O-ring, and install it to the oil strainer.


b.

Install the oil strainer with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12102A 7.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

NOTICE:

When the contact surfaces shown below are wet, wipe them with an oil-free cloth before applying seal packing.


A177349

a.
A177351E03
2.313,3.042 2.448,3.042 2.448,3.042 2.521,2.688 true 0.49,1.417 0.604,1.573 0.115,0.156 10 false a 1.031,1.417 1.146,1.573 0.115,0.156 10 false a 2.531,2.208 2.76,2.365 0.229,0.156 10 false a-a 1.052,2.406 2.25,2.594 1.198,0.188 10 false 9.0 mm (0.354 in.) 0.677,2.948 2.281,3.115 1.604,0.167 10 false Seal Diameter: 5 to 6 mm

Apply seal packing to the No. 2 oil pan as shown in the illustration.

Standard seal diameter:

5.0 to 6.0 mm (0.197 to 0.236 in.)


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

For the bolt and pin holes, make sure to apply seal packing to the inner sides.

·

Make sure to apply a continuous bead of seal packing as shown in the illustration. If the bead breaks, overlap 3.0 mm (0.118 in.) of seal packing and continue the bead.

·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan within 3 minutes and tighten the bolts and nuts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing.




b.

Install the No. 2 oil pan with the 10 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89491 8.INSTALL ENGINE OIL LEVEL SENSOR

a.

Install a new gasket and the sensor with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15609 9.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.
U163096E02
1.458,1.333 1.458,1.594 false 1,1.635 1.781,1.813 0.781,0.177 10 false New O-Ring

Apply a light coat of engine oil to 2 new O-rings, and set them to the oil filter bracket.


b.

Install the oil filter bracket with the 3 bolts and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the 2 wire harness clamps.


Hide 11348 11.INSTALL TIMING GEAR COVER SPACER (w/ Intercooler)

a.

Install the timing gear cover spacer with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16620D 13.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
U163095E02
1.646,0.094 1.802,0.26 0.156,0.167 10 false A 2.521,1.479 2.677,1.646 0.156,0.167 10 false B 2.333,1.021 2.49,1.188 0.156,0.167 10 false C 1.219,1.792 1.375,1.958 0.156,0.167 10 false C 0.583,0.458 0.74,0.625 0.156,0.167 10 false B

Install the V-ribbed belt tensioner with the 5 bolts.

Torque:
for bolt A and C : 43 N*m (438 kgf*cm, 32 ft.*lbf)
for bolt B : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length
Item Quantity Length
Bolt A 1 116 mm (4.57 in.)
Bolt B 2 40 mm (1.58 in.)
Bolt C 2 95 mm (3.74 in.)


b.

Install the No. 1 idler pulley with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Install the V-ribbed belt tensioner bracket with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15778 14.CONNECT NO. 2 OIL COOLER HOSE

a.

Align the white paint marks on the oil cooler hose and oil filter bracket and connect the hose.

NOTICE:

Make sure to maintain a space between the oil cooler hose and crankshaft pulley and the oil cooler hose and V-ribbed belt idler pulley.



Hide 15777 15.CONNECT NO. 1 OIL COOLER HOSE

a.

Face the pink paint mark on the oil cooler hose toward the front side of the engine and connect the hose to the oil filter bracket.

NOTICE:

Make sure to maintain a space between the oil cooler hose and crankshaft pulley.



Hide 12158 16.INSTALL STIFFENER INSULATOR RH (w/ Intercooler)

a.

Install the stiffener insulator RH with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15408G 17.INSTALL NO. 2 INLET TURBO OIL PIPE SUB-ASSEMBLY

a.

Install a new gasket and connect the No. 2 inlet turbo oil pipe with the union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 15492 18.CONNECT NO. 2 OUTLET TURBO OIL HOSE

Hide 11452 19.INSTALL NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring, and install it to the No. 1 engine oil level dipstick guide.


b.

Install the No. 1 engine oil level dipstick guide with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15474A 20.CONNECT NO. 1 OUTLET TURBO OIL HOSE

Hide 27020 21.INSTALL GENERATOR ASSEMBLY

a.
U162881E02
2.542,0.49 2.719,0.656 0.177,0.167 10 false 1 0.875,1.51 1.052,1.677 0.177,0.167 10 false 2 2.656,1.51 2.833,1.677 0.177,0.167 10 false 3 0.844,0.49 1.021,0.656 0.177,0.167 10 false 4 1.792,0.615 1.969,0.781 0.177,0.167 10 false 5

Temporarily install the generator with the 3 bolts and 2 nuts.


b.

Uniformly tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Connect the generator cable and install the nut and bolt.

Torque:
for bolt : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for nut (130A Type and 150A Type:) : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
for nut (180A Type:) : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 23.INSTALL ENGINE ASSEMBLY

a.

Install the engine assembly to the vehicle (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION).


Hide 24.CONNECT TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to negative (-) main battery and sub-battery terminals.