Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255249 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0500  Vehicle Speed Sensor Malfunction  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the master cylinder solenoid (skid control ECU). The master cylinder solenoid (skid control ECU) converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

DTC Code DTC Detection Condition Trouble Area
P0500 The vehicle speed signal from the vehicle speed sensor is cut for 0.14 second. or more while the cruise control is in operation.
·

Vehicle speed sensor signal circuit

·

Vehicle speed sensor

·

Combination meter

·

ECM



WIRING DIAGRAM

E149081E04
1.552,1.509 2.820,1.688 1.268,0.179 10 Combination Meter 5.671,1.677 6.105,1.844 0.434,0.167 10 ECM 5.671,1.508 6.125,1.671 0.453,0.163 10 A52*2 5.671,1.346 6.125,1.509 0.453,0.163 10 A38*1 1.542,1.34 1.924,1.503 0.383,0.163 10 E7 5.256,0.657 5.591,0.820 0.335,0.163 10 SPD 2.604,0.67 2.800,0.837 0.195,0.167 10 +S 4.804,0.375 5.136,0.538 0.331,0.163 10 13*3 0.05,2.164 2.178,2.327 2.128,0.163 10 *3: for 1GR-FE, 1UR-FE, 3UR-FE 0.05,1.876 1.125,2.039 1.075,0.163 10 *2: for RHD 0.05,1.589 1.125,1.752 1.075,0.163 10 *1: for LHD 0.05,2.452 1.096,2.615 1.046,0.163 10 *4: for 1VD-FTV 4.876,0.544 5.136,0.707 0.261,0.163 10 8*4 2.927,0.558 3.130,0.725 0.203,0.167 10 4

CAUTION / NOTICE / HINT

This DTC code may be output under the SFI system (for 1GR-FE, 1UR-FE, 3UR-FE) or the ECD system (for 1VD-FTV) at the same time. In that case, perform troubleshooting for the SFI system first.

PROCEDURE

1.CHECK ENGINE TYPE
a.

Check the engine type.

Engine Type
Engine Type Proceed to
for gasoline engine A
for diesel engine B



A

2.CHECK DTC (CRUISE CONTROL SYSTEM)

B

3.CHECK DTC (CRUISE CONTROL SYSTEM)
2.CHECK DTC (CRUISE CONTROL SYSTEM)
a.

Using the intelligent tester, enter the following menus: Powertrain / Cruise Control / Trouble Code.



c.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle for more than 10 seconds when the engine coolant temperature is more than 20°C (68°F).



d.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
OK
(DTC P0500 is not output)
A
NG
(for 1GR-FE)
B
NG
(for 1UR-FE)
C
NG
(for 3UR-FE)
D



A

B

C

D

3.CHECK DTC (CRUISE CONTROL SYSTEM)
a.

Using the intelligent tester, enter the following menus: Powertrain / Cruise Control / Trouble Code.



c.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle for more than 10 seconds when the engine coolant temperature is more than 20°C (68°F).



d.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
OK
(DTC P0500 is not output)
A
NG
(for 1VD-FTV, w/ DPF)
B
NG
(for 1VD-FTV, w/o DPF)
C



A

B

C