Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to operate 8 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCELERATION), TAP-UP, CANCEL and MODE. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCELERATION) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control MODE, SET, - (COAST), RES (RESUME), + (ACCELERATION) and CANCEL. The dynamic radar cruise control system has two cruise control modes: the constant speed control mode and vehicle-to-vehicle distance control mode.

HINT:
·

The vehicle-to-vehicle distance control mode is always selected when starting up the dynamic radar cruise control system.

·

The operation of the constant speed control mode is the same as the cruise control system.



WIRING DIAGRAM

E158924E04
6.49,2.438 6.844,2.604 0.354,0.167 10 false ECM 6.49,2.271 6.969,2.448 0.479,0.177 10 false A52*2 6.49,2.104 6.969,2.281 0.479,0.177 10 false A38*1 6.167,0.333 6.375,0.5 0.208,0.167 10 false 45 6.438,0.417 6.781,0.573 0.344,0.156 10 false CCS 6.167,1.427 6.375,1.594 0.208,0.167 10 false 37 6.427,1.542 6.854,1.698 0.427,0.156 10 false CCHG 4.896,3.104 5.74,3.313 0.844,0.208 10 false Spiral Cable 5.563,0.438 5.833,0.604 0.271,0.167 10 false E12 5.563,2.615 5.833,2.781 0.271,0.167 10 false E12 5.625,0.229 5.792,0.406 0.167,0.177 10 false 1 5.656,2.417 5.813,2.604 0.156,0.188 10 false 2 5.208,0.333 5.552,0.521 0.344,0.188 10 false CCS 5.188,2.51 5.531,2.698 0.344,0.188 10 false ECC 5.563,1.552 5.833,1.719 0.271,0.167 10 false E12 5.646,1.344 5.802,1.531 0.156,0.188 10 false 7 5.188,1.344 5.531,1.531 0.344,0.188 10 false R/N 3.656,0.344 4,0.531 0.344,0.188 10 false CCS 3.656,2.521 4,2.708 0.344,0.188 10 false ECC 3.25,1.719 3.708,1.906 0.458,0.188 10 false MODE 3.719,1.448 4.063,1.635 0.344,0.188 10 false R/N 3.844,3.135 4.823,3.49 0.979,0.354 10 false Cruise Control Switch Wire 1.167,2.99 2.938,3.198 1.771,0.208 10 false Cruise Control Main Switch 0.125,3.156 0.958,3.417 0.833,0.26 10 false *1: for LHD 0.125,3.417 0.958,3.677 0.833,0.26 10 false *2: for RHD 3.073,0.906 3.646,1.104 0.573,0.198 10 false ON-OFF 2.188,0.906 2.656,1.083 0.469,0.177 10 false + RES 1.313,0.896 1.781,1.073 0.469,0.177 10 false - SET 0.417,0.906 1.052,1.083 0.635,0.177 10 false CANCEL 4.094,2.5 4.26,2.677 0.167,0.177 10 false 1 4.708,0.24 4.875,0.417 0.167,0.177 10 false 3 4.708,2.406 4.865,2.594 0.156,0.188 10 false 4 4.083,0.323 4.24,0.51 0.156,0.188 10 false 3 4.635,0.438 4.885,0.604 0.25,0.167 10 false z37 4.635,1.552 4.885,1.719 0.25,0.167 10 false z37 4.635,2.615 4.885,2.781 0.25,0.167 10 false z37 4.094,1.427 4.26,1.604 0.167,0.177 10 false 2 4.708,1.344 4.865,1.531 0.156,0.188 10 false 1

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)
E149034E01
2.676,1.645 3.245,1.816 0.569,0.171 10 ON-OFF 1.455,0.394 1.879,0.596 0.424,0.202 10 +RES 0.127,2.375 0.756,2.577 0.629,0.202 10 CANCEL 1.469,2.81 1.836,3.012 0.367,0.202 10 -SET 2.732,0.877 3.199,1.047 0.467,0.171 10 MODE

a.

Using the intelligent tester, read the Data List (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Radar Cruise
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
CCS Main SW M-CPU Cruise control main switch (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal / ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal / ON or OFF ON: +RES switch on
OFF: +RES switch off
-
CCS Main SW S-CPU Cruise control main switch (Sub CPU) / ON or OFF ON: Cruise control main switch (Sub CPU) on
OFF: Cruise control main switch (Sub CPU) off
-

OK:

The intelligent tester display changes according to operation of cruise control main switch.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
E149029E01
1.891,1.925 2.602,2.127 0.711,0.202 10 CANCEL 1.497,3.33 1.836,3.532 0.339,0.202 10 ECC 0.492,3.311 0.878,3.513 0.387,0.202 10 CCS 4.068,0.888 4.714,1.090 0.646,0.202 10 ON-OFF 3.867,0.158 4.340,0.360 0.473,0.202 10 MODE 2.034,2.264 4.582,2.663 2.549,0.399 10 Component without harness connected: (Cruise Control Main Switch) 0.892,2.991 0.709,3.311 false 1.448,2.998 1.544,3.33 false 1.161,3.33 1.460,3.532 0.299,0.202 10 R/N 1.111,2.998 1.207,3.33 false 4.753,0.058 6.529,0.270 1.776,0.211 10 Cruise Control Main Switch 6.575,3.842 6.740,4.017 0.165,0.174 10 2 6.581,2.895 6.735,3.081 0.154,0.186 10 3 6.575,3.07 6.913,3.244 0.337,0.174 10 CCS 6.581,4.028 6.946,4.214 0.365,0.186 10 R/N 6.575,4.283 6.740,4.458 0.165,0.174 10 1 6.581,4.469 6.946,4.655 0.365,0.186 10 ECC 5.359,3.456 5.920,3.627 0.562,0.171 10 ON-OFF 5.606,4.017 6.089,4.188 0.483,0.171 10 MODE 4.471,3.463 4.941,3.642 0.471,0.179 10 + RES 3.593,3.463 4.064,3.642 0.470,0.179 10 - SET 2.695,3.463 3.329,3.642 0.633,0.179 10 CANCEL 2.823,0.231 3.246,0.433 0.423,0.202 10 +RES 3.661,1.984 4.051,2.186 0.391,0.202 10 -SET

a.

Remove the cruise control main switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (ECC) - 3 (CCS) Neutral 1 MΩ or higher
Pushed to +RES 235 to 245 Ω
Pushed to -SET 620 to 640 Ω
Pushed to CANCEL 1510 to 1570 Ω
Main switch pushed off 1 MΩ or higher
Main switch pushed on Below 2.5 Ω
1 (ECC) - 2 (R/N) MODE switch pushed on Below 2.5 Ω
MODE switch off 1 MΩ or higher




OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

3.INSPECT CRUISE CONTROL SWITCH WIRE
U165807E02
0.083,2.323 2.438,2.677 2.354,0.354 10 false Front view of wire harness connector: (to Cruise Control Main Switch) 0.073,0.063 2.396,0.385 2.323,0.323 10 false Front view of wire harness connector: (to Spiral Cable) 0.302,1.438 0.552,1.583 0.25,0.146 10 false z37

a.

Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 - 3 Always Below 1 Ω
z37-1 - 2
z37-4 - 1
z37-3 - Body ground Always 10 kΩ or higher
z37-1 - Body ground
z37-4 - Body ground




OK

4.INSPECT SPIRAL CABLE

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE
E349645E01
3.729,0.396 4.063,0.646 0.333,0.25 4.344,2.406 4.656,2.625 0.313,0.219 4.552,2.875 4.729,2.896 true 5.094,3.469 4.833,3.021 true 4.531,3.344 4.74,3.031 true 3.781,0.427 4.24,0.625 0.458,0.198 10 false z37 4.375,2.417 4.833,2.615 0.458,0.198 10 false E12 4.271,2.792 4.729,2.99 0.458,0.198 10 false R/N 4.323,3.365 4.781,3.563 0.458,0.198 10 false CCS 4.979,3.479 5.438,3.677 0.458,0.198 10 false ECC 0.115,0.073 2.583,0.667 2.469,0.594 10 false Component without harness connected: (Spiral Cable)

a.

Check the spiral cable and connector for scratches, cracks, dents and chips. If any defects are found, replace the spiral cable with a new one.


b.

Check the spiral cable.

i.

Set the spiral cable to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).


ii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 - E12-1 (CCS) Always Below 1 Ω
z37-1 - E12-7 (R/N)
z37-4 - E12-2 (ECC)



iii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.


Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 - E12-1 (CCS) Always Below 1 Ω
z37-1 - E12-7 (R/N)
z37-4 - E12-2 (ECC)





OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
E349646E01
0.365,0.708 0.688,0.927 0.323,0.219 5.01,0.396 5.333,0.615 0.323,0.219 5.792,0.396 6.115,0.615 0.323,0.219 1.177,1.135 1.646,1.281 true 1.823,1.198 2.615,0.938 true 1.198,1.552 1.646,1.417 true 5.354,2.167 5.885,1.677 true 6.344,2.219 5.896,1.563 true 0.365,0.094 2.75,0.667 2.385,0.573 10 false Front view of wire harness connector: (to Spiral Cable) 4.292,0.094 6.667,0.698 2.375,0.604 10 false Front view of wire harness connector: (to ECM) 0.865,0.969 1.323,1.167 0.458,0.198 10 false CCS 0.865,1.563 1.323,1.76 0.458,0.198 10 false R/N 2.698,0.833 3.156,1.031 0.458,0.198 10 false ECC 5.052,0.417 5.51,0.615 0.458,0.198 10 false A38 5.833,0.417 6.292,0.615 0.458,0.198 10 false A52 6.146,0.417 6.604,0.615 0.458,0.198 10 false *2 5.396,0.427 5.854,0.625 0.458,0.198 10 false *1 0.156,2.156 1.052,2.396 0.896,0.24 10 false *1: for LHD 0.188,2.448 1.146,2.667 0.958,0.219 10 false *2: for RHD 5.177,2.229 5.635,2.427 0.458,0.198 10 false CCS 6.198,2.292 6.656,2.49 0.458,0.198 10 false CCHG 0.417,0.74 0.875,0.938 0.458,0.198 10 false E12

a.

Disconnect the E12 spiral cable connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E12-1 (CCS) - A38-45 (CCS) Always Below 1 Ω
E12-7 (R/N) - A38-37 (CCHG)
E12-1 (CCS) - Body ground Always 10 kΩ or higher
E12-7 (R/N) - Body ground
E12-2 (ECC) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
E12-1 (CCS) - A52-45 (CCS) Always Below 1 Ω
E12-7 (R/N) - A52-37 (CCHG)
E12-1 (CCS) - Body ground Always 10 kΩ or higher
E12-7 (R/N) - Body ground
E12-2 (ECC) - Body ground Always Below 1 Ω



Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 3UR-FE) B
NG C


A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR