Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a lane departure alert main switch signal from the steering pad switch assembly and sends the signal to the forward recognition camera via CAN communication.

WIRING DIAGRAM

C349676E01
0.927,2.667 3.042,2.938 2.115,0.271 10 false Steering Pad Switch Assembly 1.313,0.729 2.896,0.917 1.583,0.188 10 false Distance Control Switch 3.042,0.594 3.313,0.781 0.271,0.188 10 false z73 3.052,2.042 3.323,2.229 0.271,0.188 10 false z73 3.344,2.604 4.479,3.156 1.135,0.552 10 false Spiral Cable Sub-assembly 3.125,0.375 3.313,0.573 0.188,0.198 10 false 4 3.125,1.813 3.313,2.01 0.188,0.198 10 false 7 4.24,0.594 4.646,0.76 0.406,0.167 10 false E122 4.24,2.042 4.646,2.208 0.406,0.167 10 false E122 4.323,0.375 4.542,0.563 0.219,0.188 10 false 12 4.354,1.781 4.625,1.948 0.271,0.167 10 false 2 2.51,0.49 2.885,0.688 0.375,0.198 10 false DIST 3.396,0.5 3.771,0.698 0.375,0.198 10 false DIST 3.813,0.5 4.188,0.698 0.375,0.198 10 false DIST 2.594,1.896 2.948,2.063 0.354,0.167 10 false ECC 3.427,1.906 3.781,2.073 0.354,0.167 10 false ECC 3.844,1.906 4.198,2.073 0.354,0.167 10 false ECC 5.438,0.51 5.667,0.667 0.229,0.156 10 false 23 5.667,0.594 6.177,0.781 0.51,0.188 10 false SPSW 5.521,1.167 6.604,1.708 1.083,0.542 10 false Driving Support ECU Assembly 5.25,1 5.698,1.156 0.448,0.156 10 false E164 6.375,2.979 6.927,3.25 0.552,0.271 10 false ECM 6.208,2.531 6.573,2.74 0.365,0.208 10 false E1 6.198,2.042 6.813,2.24 0.615,0.198 10 false ECCS*1 5.833,2.042 6.188,2.229 0.354,0.188 10 false A38 5.875,1.813 6.208,2.042 0.333,0.229 10 false 59 5.823,2.542 6.219,2.729 0.396,0.188 10 false C45 5.875,2.271 6.104,2.438 0.229,0.167 10 false 81 5.333,1.885 5.563,2.094 0.229,0.208 10 false *1 5.073,2.24 5.271,2.417 0.198,0.177 10 false *2 0.323,3.031 2.479,3.229 2.156,0.198 10 false *1: for 3UR-FE 0.323,3.344 2.479,3.542 2.156,0.198 10 false *2: except 3UR-FE

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the E122 spiral cable sub-assembly connector.


b.

Disconnect the E164 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-12 (DIST) - E164-23 (SPSW) Always Below 1 Ω
E122-12 (DIST) or E164-23 (SPSW) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for 3UR-FE) A
OK (except 3UR-FE) B
NG C




A

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)

B

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the E122 spiral cable sub-assembly connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-2 (ECC) - A38-59 (ECCS) Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (ECM- BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM- BODY GROUND)
a.

Disconnect the C45 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the E122 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-2 (ECC) - Body ground Always Below 1 Ω




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR