Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P0571/76  Brake Switch "A" Circuit  


DESCRIPTION

The ECM receives the brake demand signal from the driving support ECU assembly and transmits it to the skid control ECU (master cylinder solenoid).

The skid control ECU (master cylinder solenoid) receives a signal from the ECM and operates the skid control ECU (master cylinder solenoid).

The skid control ECU (master cylinder solenoid) operates simultaneously the STP LP OPE relay (brake light relay) and illuminates the stop rights.

DTC No. DTC Detection Condition Trouble Area
P0571/76 While the dynamic radar cruise control system is operating (vehicle-to-vehicle distance control mode), the ECM detects the STP LP OPE relay (brake light relay) signal from the skid control ECU (master cylinder solenoid) for approximately 0.2 seconds or more.
·

STP LP OPE relay (brake light relay)

·

Skid control ECU (master cylinder solenoid)

·

Harness or connector



WIRING DIAGRAM

E331221E13
1.896,1.083 2.271,1.271 0.375,0.188 10 false ECM 0.375,2.031 1.188,2.219 0.813,0.188 10 false from Battery 0.25,1.563 1.396,1.74 1.146,0.177 10 false from IG Circuit 1.531,1.698 2.5,1.917 0.969,0.219 10 false ECU-IG NO. 1 1.771,2.198 2.25,2.417 0.479,0.219 10 false STOP 3.24,2.698 4.813,3.24 1.573,0.542 10 false STP LP OPE Relay (Brake Light Relay) 3.115,1.427 3.323,1.635 0.208,0.208 10 false 1 3.104,1.896 3.313,2.104 0.208,0.208 10 false 5 3.104,2.219 3.313,2.427 0.208,0.208 10 false 4 4.406,1.427 4.615,1.635 0.208,0.208 10 false 2 4.417,2.052 4.625,2.26 0.208,0.208 10 false 3 5.51,1.417 5.771,1.604 0.26,0.188 10 false 16 5.51,2.063 5.771,2.25 0.26,0.188 10 false 45 5.823,1.417 6.281,1.604 0.458,0.188 10 false STPO 5.823,2.063 6.281,2.25 0.458,0.188 10 false STP2 5.823,3.469 6.281,3.656 0.458,0.188 10 false STP 5.573,3.469 5.781,3.677 0.208,0.208 10 false 7 3.104,3.49 4.271,3.875 1.167,0.385 10 false from Stop Light Switch Assembly 0.438,4.729 2.688,5.042 2.25,0.313 10 false Stop Light Control Relay Assembly 0.448,4.552 0.74,4.76 0.292,0.208 10 false A39 2.167,3.281 2.51,3.5 0.344,0.219 10 false OUT 0.906,3.281 1.177,3.448 0.271,0.167 10 false +B 0.677,3.302 0.885,3.51 0.208,0.208 10 false 6 2.594,3.26 2.802,3.469 0.208,0.208 10 false 8 0.667,4.125 0.875,4.333 0.208,0.208 10 false 4 2.167,4.115 2.625,4.302 0.458,0.188 10 false STP 0.917,4.115 1.292,4.323 0.375,0.208 10 false GND 5.344,4.177 5.677,4.385 0.333,0.208 10 false A24 5.323,4.365 7.031,4.99 1.708,0.625 10 false Skid Control ECU (Master Cylinder Solenoid) 4.323,4.688 4.781,4.875 0.458,0.188 10 false STP 3.375,4.677 3.708,4.927 0.333,0.25 10 false E 3.135,4.667 3.344,4.875 0.208,0.208 10 false 3 4.729,4.677 4.938,4.885 0.208,0.208 10 false 5 2.875,5.073 3.219,5.292 0.344,0.219 10 false L3 2.823,5.24 5.24,5.51 2.417,0.271 10 false Rear Combination Light Assembly RH 0.75,5.979 1.021,6.24 0.271,0.26 10 false K4 0.729,6.198 3.76,6.385 3.031,0.188 10 false Rear Combination Light Assembly LH 2.188,5.625 2.646,5.813 0.458,0.188 10 false STP 1.208,5.635 1.542,5.885 0.333,0.25 10 false E 2.583,5.615 2.792,5.823 0.208,0.208 10 false 5 0.979,5.635 1.188,5.844 0.208,0.208 10 false 3 1.302,7.688 3.271,7.917 1.969,0.229 10 false Center Stop Light Assembly 1.302,7.49 1.677,7.719 0.375,0.229 10 false S4 2.333,7.063 2.594,7.302 0.26,0.24 10 false B 1.708,7.063 2.042,7.313 0.333,0.25 10 false E 2.594,7.052 2.802,7.26 0.208,0.208 10 false 1 1.5,7.073 1.708,7.281 0.208,0.208 10 false 2 5.146,7.448 5.521,7.667 0.375,0.219 10 false S34 5.156,7.656 6.771,7.844 1.615,0.188 10 false Rear Light Assembly LH 5.302,5.958 5.635,6.188 0.333,0.229 10 false S35 5.292,6.177 6.917,6.448 1.625,0.271 10 false Rear Light Assembly RH 5.833,5.635 6.094,5.875 0.26,0.24 10 false B 6.479,5.635 6.813,5.885 0.333,0.25 10 false E 5.823,7.063 6.083,7.302 0.26,0.24 10 false B 6.458,7.063 6.792,7.313 0.333,0.25 10 false E 5.604,5.635 5.813,5.844 0.208,0.208 10 false 1 6.698,5.625 6.906,5.833 0.208,0.208 10 false 4 5.604,7.063 5.813,7.271 0.208,0.208 10 false 1 6.698,7.052 6.906,7.26 0.208,0.208 10 false 4 0.635,8.375 2.417,8.583 1.781,0.208 10 false : CAN Communication Line 2.594,4.125 2.792,4.375 0.198,0.25 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the master cylinder solenoid, perform zero point calibration and store the system information (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

When the start function does not operate, check the smart key system (for start function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

2.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID STPO TERMINAL VOLTAGE)

NG

GO TO LIGHTING SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID STPO TERMINAL VOLTAGE)
a.

Disconnect the skid control ECU (master cylinder solenoid) connector.


b.
U156827E01
0.086,0.103 0.325,0.363 0.239,0.260 10 *a 2.621,0.37 3.051,0.543 0.430,0.173 10 STPO 2.303,1.195 2.411,0.438 2.411,0.438 2.595,0.438 false 1.61,0.415 1.905,0.571 0.295,0.156 10 A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-16 (STPO) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

3.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID STP2 TERMINAL VOLTAGE)

NG

7.CHECK HARNESS AND CONNECTOR (STP LP OPE RELAY - MASTER CYLINDER SOLENOID AND BATTERY)
3.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID STP2 TERMINAL VOLTAGE)
a.

Disconnect the skid control ECU (master cylinder solenoid) connector.


b.
U156828E05
2.24,1.427 2.469,1.906 2.469,1.906 2.656,1.906 false 0.083,0.052 0.323,0.313 0.24,0.26 10 false *a 2.708,1.802 3.135,1.979 0.427,0.177 10 false STP2 1.635,0.417 1.927,0.573 0.292,0.156 10 false A24

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-45 (STP2) - Body ground Brake pedal depressed 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])



OK

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.


b.

Perform the Active Test according to the display on the GTS.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay STP LP OPE relay (Brake light relay) Relay ON/OFF Observe the stop light (the stop lights do not come on for 2 to 5 seconds).


c.

Check the STP LP OPE relay (brake light relay) operation using the Data List and stop light operation by performing an Active Test.

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output STP LP OPE relay (Brake light relay) output/ ON or OFF ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off)
-

Result:
Result Proceed to
The Data List item "Stop Light Relay Output" switches between ON and OFF when turning the stop light control relay on and off with the Active Test, but the stop lights do not illuminate or turn off A
The Data List item "Stop Light Relay Output" does not switch between ON and OFF when turning the stop light control relay on and off with the Active Test (for LHD) B
The Data List item "Stop Light Relay Output" switches between ON and OFF when turning the stop light control relay on and off with the Active Test and the stop lights illuminate and turn off (for LHD)
The Data List item "Stop Light Relay Output" does not switch between ON and OFF when turning the stop light control relay on and off with the Active Test (for RHD) C
The Data List item "Stop Light Relay Output" switches between ON and OFF when turning the stop light control relay on and off with the Active Test and the stop lights illuminate and turn off (for RHD)




A

5.INSPECT STP LP OPE RELAY (BRAKE LIGHT RELAY)

B

C

5.INSPECT STP LP OPE RELAY (BRAKE LIGHT RELAY)
a.

Turn the engine switch off.


b.

Remove the STP LP OPE relay (brake light relay) from the engine room relay block and junction block assembly.


c.

Inspect the STP LP OPE relay (brake light relay) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (STP LP OPE RELAY - BATTERY)

NG

REPLACE STP LP OPE RELAY (BRAKE LIGHT RELAY)

6.CHECK HARNESS AND CONNECTOR (STP LP OPE RELAY - BATTERY)
a.

Turn the engine switch off.


b.

Remove the STP LP OPE relay (brake light relay) from the engine room relay block and junction block assembly.


c.
E331226E07
0.146,0.135 0.542,0.385 0.396,0.25 10 false *1 2.688,1.74 3.083,1.99 0.396,0.25 10 false *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
STP LP OPE relay (brake light relay) holder terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 STP LP OPE Relay (Brake Light Relay) Holder Terminal

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STP LP OPE RELAY - MASTER CYLINDER SOLENOID AND BATTERY)
a.

Turn the engine switch off.


b.

Remove the STP LP OPE relay (brake light relay) from the engine room relay block and junction block assembly.


c.

Disconnect the A24 skid control ECU (master cylinder solenoid) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
STP LP OPE relay (brake light relay) holder terminal 2 - A24-16 (STPO) Always Below 1 Ω
STP LP OPE relay (brake light relay) holder terminal 2 or A24-16 (STPO) - Body ground Always 10 kΩ or higher



e.
E331226E07
0.146,0.135 0.542,0.385 0.396,0.25 10 false *1 2.688,1.74 3.083,1.99 0.396,0.25 10 false *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
STP LP OPE relay (brake light relay) holder terminal 1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 STP LP OPE Relay (Brake Light Relay) Holder Terminal



OK

REPLACE STP LP OPE RELAY (BRAKE LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR