Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255255 LANE DEPARTURE ALERT SYSTEM J

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The driving support ECU assembly receives a lane departure alert main switch signal from the steering pad switch assembly and sends the signal to the forward recognition camera via CAN communication.

WIRING DIAGRAM

C349679E04
4.26,0.5 4.438,0.656 0.177,0.156 10 false 23 4.5,0.542 5.021,0.76 0.521,0.219 10 false SPSW 3.198,0.594 3.708,0.833 0.51,0.24 10 false E122 1.99,0.594 2.271,0.823 0.281,0.229 10 false z73 2.063,0.948 2.208,1.135 0.146,0.188 10 false 7 2.063,0.385 2.188,0.583 0.125,0.198 10 false 4 3.313,0.958 3.479,1.167 0.167,0.208 10 false 2 3.271,0.365 3.531,0.594 0.26,0.229 10 false 12 4.219,1.938 5.635,2.51 1.417,0.573 10 false Driving Support ECU Assembly 4.219,1.771 4.646,1.969 0.427,0.198 10 false E164 2.313,1.688 3.448,2.188 1.135,0.5 10 false Spiral Cable Sub-assembly 0.156,2.354 2.146,2.573 1.99,0.219 10 false Steering Pad Switch Assembly 0.396,1.344 1.792,1.99 1.396,0.646 10 false Lane Departure Alert Main Switch 2.552,0.49 2.958,0.688 0.406,0.198 10 false DIST 2.563,1.104 2.958,1.333 0.396,0.229 10 false ECC 0.594,3.333 2.635,3.531 2.042,0.198 10 false : CAN Communication Line 6.208,1.979 7,2.656 0.792,0.677 10 false Forward Recognition Camera 6.208,1.792 6.542,2 0.333,0.208 10 false R20 6.219,0.813 6.719,1.021 0.5,0.208 10 false CANL 6.219,1.188 6.74,1.417 0.521,0.229 10 false CANH 4.813,0.802 5.302,1.01 0.49,0.208 10 false CA1N 4.823,1.229 5.385,1.448 0.563,0.219 10 false CA1P 5.958,0.667 6.135,0.823 0.177,0.156 10 false 12 6.021,1.052 6.135,1.208 0.115,0.156 10 false 6 5.292,0.667 5.406,0.833 0.115,0.167 10 false 9 5.292,1.073 5.406,1.24 0.115,0.167 10 false 8 1.99,1.208 2.271,1.427 0.281,0.219 10 false z73 4.667,3.417 5.094,3.615 0.427,0.198 10 false ECM 4.49,2.844 5.01,3.167 0.521,0.323 10 false ECCS 4.25,2.74 4.458,2.938 0.208,0.198 10 false 59 4.667,3.25 5.042,3.469 0.375,0.219 10 false A38 4.094,2.958 4.292,3.135 0.198,0.177 10 false *1 3.667,3.135 3.906,3.323 0.24,0.188 10 false *2 0.469,2.677 1.792,2.854 1.323,0.177 10 false *1: for 3UR-FE 0.469,2.969 1.917,3.167 1.448,0.198 10 false *2: except 3UR-FE 3.198,1.198 3.677,1.427 0.479,0.229 10 false E122

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSPECTION).



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the E122 spiral cable sub-assembly connector.


b.

Disconnect the E164 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-12 (DIST) - E164-23 (SPSW) Always Below 1 Ω
E122-12 (DIST) or E164-23 (SPSW) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM OR BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM OR BODY GROUND)
a.

for 3UR-FE:

i.

Disconnect the E122 spiral cable sub-assembly connector.


ii.

Disconnect the A38 ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-2 (ECC) - A38-59 (ECCS) Always Below 1 Ω




b.

except 3UR-FE:

i.

Disconnect the E122 spiral cable sub-assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E122-2 (ECC) - Body ground Always Below 1 Ω





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR