Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION UNIT › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255301 AUTOMATIC TRANSMISSION UNIT A

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

a.

Check each bearing position and installation direction.

C336515E01
6.051,2.816 6.207,2.997 0.156,0.181 10 A 3.385,2.839 3.541,3.020 0.156,0.181 10 B 4.065,2.569 4.221,2.750 0.156,0.181 10 C 5.04,2.165 5.196,2.346 0.156,0.181 10 D 2.092,6.808 2.248,6.989 0.156,0.181 10 E 2.875,6.714 3.031,6.896 0.156,0.181 10 F 6.657,6.039 6.813,6.220 0.156,0.181 10 G 1.161,6.383 1.317,6.564 0.156,0.181 10 H

Bearing Position:
Position Front Race Diameter
Inside/Outside
Thrust Bearing Diameter
Inside/Outside
Rear Race Diameter
Inside/Outside
A - 36.2 mm (1.425 in.) / 58.2 mm (2.291 in.) 44.0 mm (1.732 in.) / 62.0 mm (2.441 in.)
B - 34.5 mm (1.358 in.) / 49.9 mm (1.965 in.) 36.6 mm (1.441 in.) / 51.9 mm (2.043 in.)
C 46.5 mm (1.831 in.) / 60.1 mm (2.366 in.) 47.0 mm (1.850 in.) / 61.9 mm (2.437 in.) -
D - 71.2 mm (2.803 in.) / 84.5 mm (3.327 in.) 71.9 mm (2.831 in.) / 87.8 mm (3.457 in.)
E 30.0 mm (1.181 in.) / 49.9 mm (1.965 in.) 31.0 mm (1.221 in.) / 53.7 mm (2.112 in.) -
F 31.5 mm (1.240 in.) / 57.3 mm (2.256 in.) 28.7 mm (1.130 in.) / 53.8 mm (2.118 in.) 28.7 mm (1.130 in.) / 53.5 mm (2.106 in.)
G 26.2 mm (1.031 in.) / 52.7 mm (2.075 in.) 29.3 mm (1.154 in.) / 51.2 mm (2.016 in.) 29.3 mm (1.154 in.) / 54.0 mm (2.126 in.)
H - 58.9 mm (2.319 in.) / 76.7 mm (3.020 in.) 62.0 mm (2.441 in.) / 82.5 mm (3.248 in.)



Hide 35073D 2.INSTALL OUTPUT SHAFT REAR RADIAL BALL BEARING

a.
C336504E01
1.69,1.708 2.031,1.920 0.341,0.211 10 SST 1.861,1.297 1.861,1.692 false

Using SST, tap in a new output shaft rear radial ball bearing to the automatic transmission case sub-assembly.

SST
09316-60011  (09316-00011, 09316-00021)

HINT:

Install the output shaft rear radial ball bearing so that there is no clearance between the output shaft rear radial ball bearing and the automatic transmission case sub-assembly.



b.

Using needle-nose pliers, install the snap ring.


Hide 35629 3.INSTALL 1ST AND REVERSE BRAKE PLATE STOPPER SPRING

a.
C341794

Install the 1st and reverse brake plate stopper spring to the automatic transmission case sub-assembly.

NOTICE:

The shapes of the parts are different. Refer to the illustration when installing the parts.



Hide 35622G 4.INSTALL NO. 2 BRAKE PISTON

a.

Coat 3 new O-rings with ATF, and install them to the No. 2 brake piston.


b.
C336516E01
2.914,0.504 3.121,0.711 0.207,0.207 10 *a 0.137,2.885 0.344,3.092 0.207,0.207 10 *b 0.237,2.87 0.237,2.707 0.237,2.707 0.458,2.475 false 2.886,0.606 2.74,0.606 2.74,0.606 2.227,0.861 false 2.99,3.038 3.197,3.245 0.207,0.207 10 *c 2.977,3.131 2.799,3.131 2.799,3.131 2.135,3.447 false

Install the No. 2 brake piston to the automatic transmission case sub-assembly.

Text in Illustration
*a Spline
*b Protrusion
*c Spline and Protrusion

HINT:

Make sure that the parking hole of the No. 2 brake piston is on the bottom side by engaging the 2 protrusions of the brake piston to the spline grooves of the transmission case.



c.

Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly.


d.
C336505E05
1.469,0.813 0.938,0.813 true 1.875,1.333 1.99,1.333 1.99,1.333 2.125,1.49 false 2.125,0.615 2.344,0.188 2.344,0.188 2.448,0.188 true 0.573,0.729 0.885,0.917 0.313,0.188 10 false SST 1.667,1.25 1.854,1.417 0.188,0.167 10 false *2 2.458,0.104 2.667,0.302 0.208,0.198 10 true *1

Set SST on the No. 2 brake piston return spring sub-assembly, tighten SST and compress the No. 2 brake piston return spring sub-assembly.

SST
09380-50010  (09381-05010, 09381-05020, 09381-05030, 09381-05040, 09381-05050)

Text in Illustration
*1 No. 2 Brake Piston Return Spring Sub-assembly
*2 Snap Ring


e.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 35652C 6.INSTALL DIRECT CLUTCH PISTON

a.

Coat a new O-ring with ATF, and install it to the direct clutch drum sub-assembly.


b.

Coat a new O-ring with ATF, and install it to the direct clutch piston.


c.
C358674E01
0.354,1.458 0.354,1.333 0.354,1.333 0.594,1.083 false 0.313,1.5 0.625,1.698 0.313,0.198 10 false *1

Install the direct clutch piston to the direct clutch drum sub-assembly.

Text in Illustration
*1 Direct Clutch Piston


d.

Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.


e.
C148206E01
0.616,0.547 0.523,0.219 0.523,0.219 0.397,0.219 false 0.201,0.14 0.357,0.322 0.156,0.181 10 *1 0.137,1.116 0.293,1.298 0.156,0.181 10 *2 0.557,1.534 0.464,1.205 0.464,1.205 0.338,1.205 false

Install the direct clutch return spring sub-assembly and No. 2 clutch balancer to the direct clutch drum sub-assembly.

Text in Illustration
*1 No. 2 Clutch Balancer
*2 Direct Clutch Return Spring Sub-assembly


f.
C148205E01
2.808,0.156 3.144,0.337 0.335,0.181 10 SST 2.077,0.361 2.776,0.24 2.776,0.24 2.578,1.153 false

Place SST on the No. 2 clutch balancer and compress the direct clutch return spring sub-assembly with a press.

SST
09387-00020  


g.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 35667B 7.INSTALL NO. 2 CLUTCH DISC SET

a.
C336499E01
1.333,0.229 1.573,0.042 1.573,0.042 1.76,0.042 false 1.385,0.354 1.802,0.354 false 1.635,1.5 1.635,0.354 false 1.385,0.542 1.635,0.542 false 1.385,0.729 1.635,0.729 false 1.385,0.927 1.635,0.927 false 1.385,1.125 1.635,1.125 false 1.385,1.313 1.635,1.313 false 1.385,1.5 1.635,1.5 false 0.729,1.594 0.302,1.594 false 0.729,0.438 0.448,0.438 0.448,0.438 0.448,1.594 false 0.729,0.625 0.448,0.625 false 0.729,0.823 0.448,0.823 false 0.729,1.01 0.448,1.01 false 0.729,1.198 0.448,1.198 false 0.729,1.385 0.448,1.385 false 1.771,0 1.979,0.177 0.208,0.177 10 false *1 1.813,0.271 2.021,0.448 0.208,0.177 10 false *2 0.104,1.51 0.281,1.688 0.177,0.177 10 false *3

Install the 7 No. 2 clutch plates, 7 No. 2 clutch discs and the No. 2 clutch flange to the direct clutch drum sub-assembly.

Install in order:

*3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


Text in Illustration
*1 No. 2 Clutch Flange
*2 No. 2 Clutch Disc
*3 No. 2 Clutch Plate

NOTICE:

Make sure that the No. 2 clutch discs, No. 2 clutch plates and the No. 2 clutch flange are installed in the correct order.



b.
C382635E01
0.615,0.76 0.854,0.76 0.854,0.76 1.344,1.031 true 0.396,0.656 0.625,0.927 0.229,0.271 10 false *a

Using a screwdriver, install the snap ring to the direct clutch drum sub-assembly.

Text in Illustration
*a Protective Tape

NOTICE:

Be careful not to damage the direct clutch drum sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 35605A 9.INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C344389E01
2.482,1.07 2.676,1.261 0.194,0.191 10 *1 2.158,1.157 2.473,1.157 false

Coat a new oil seal ring with ATF, and install them to the direct multiple disc clutch assembly.

Text in Illustration
*1 Oil Seal Ring

NOTICE:

Do not expand the gap of the oil seal rings excessively.



b.
C341838E01
0.713,1.955 0.893,2.119 0.180,0.164 10 *1 1.796,1.914 1.796,2.042 1.796,2.042 0.909,2.042 false 1.451,1.818 1.451,2.04 false

Coat 2 new oil seal ring with ATF, and install them to the output shaft sub-assembly.

Text in Illustration
*1 Oil Seal Ring

NOTICE:

Do not expand the gap of the oil seal rings excessively.



c.
C341837E01
0.58,0.217 0.302,0.217 false 2.222,1.53 2.292,1.726 2.292,1.726 2.406,1.726 false 0.102,0.138 0.279,0.321 0.177,0.183 10 *1 1.929,0.601 2.097,0.776 0.169,0.174 10 *2 2.235,0.532 2.409,0.710 0.174,0.177 10 *3 2.426,1.64 2.611,1.826 0.184,0.185 10 *4 1.625,0.67 1.781,0.852 0.156,0.181 10 *3 1.743,0.513 1.743,0.659 false 2.044,0.446 2.044,0.592 false 2.352,0.377 2.352,0.523 false

Install the thrust needle roller bearing and 2 thrust bearing races to the direct multiple disc clutch assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
for Front Side:
Thrust bearing race (G)
26.2 mm (1.031 in.) 52.7 mm (2.075 in.)
Thrust needle roller bearing (G) 29.3 mm (1.154 in.) 51.2 mm (2.016 in.)
for Rear Side:
Thrust bearing race (G)
29.3 mm (1.154 in.) 54.0 mm (2.126 in.)


Text in Illustration
*1 Direct Multiple Disc Clutch Assembly
*2 Thrust Needle Roller Bearing (G)
*3 Thrust Bearing Race (G)
*4 Output Shaft Sub-assembly

NOTICE:

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.



d.

Install the direct multiple disc clutch assembly to the output shaft sub-assembly.


Hide 35761 10.INSTALL REAR PLANETARY RING GEAR

a.
C341836E02
2.241,2.423 2.85,2.423 false 2.23,3.267 2.84,3.267 false 2.866,2.339 3.041,2.520 0.174,0.181 10 *1 2.866,3.18 3.064,3.355 0.198,0.174 10 *2 2.842,3.885 3.039,4.059 0.198,0.174 10 *3 2.213,3.975 2.823,3.975 false

Install the snap ring to the groove of the output shaft sub-assembly.

Text in Illustration
*1 Rear Planetary Ring Gear
*2 Snap Ring
*3 Output Shaft Sub-assembly


b.

Using needle-nose pliers, attach the snap ring to install the rear planetary ring gear to the output shaft sub-assembly.


Hide 11.INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY WITH REAR PLANETARY RING GEAR AND OUTPUT SHAFT SUB-ASSEMBLY

a.
C337019E04
1.604,0.198 1.167,0.198 false 1.604,0.438 1.167,0.438 false 1.594,2.49 1.271,1.771 1.271,1.771 1.073,1.771 false 1.563,2.781 1.146,2.177 1.146,2.177 0.979,2.177 false 0.979,0.115 1.146,0.271 0.167,0.156 10 false *1 0.969,0.354 1.135,0.531 0.167,0.177 10 false *2 0.865,1.688 1.042,1.854 0.177,0.167 10 false *1 0.771,2.094 0.958,2.271 0.188,0.177 10 false *2 2.031,2.604 2.26,2.792 0.229,0.188 10 true (H) 2,0.219 2.24,0.427 0.24,0.208 10 false (F)

Install the 2 thrust needle bearings, 2 thrust bearing races, direct multiple disc clutch assembly with rear planetary ring gear and output shaft sub-assembly to the automatic transmission case sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
Thrust bearing race (H) 62.0 mm (2.441 in.) 82.5 mm (3.248 in.)
Thrust needle roller bearing (H) 58.9 mm (2.319 in.) 76.7 mm (3.020 in.)
for Rear Side:
Thrust bearing race (F)
28.7 mm (1.130 in.) 53.5 mm (2.106 in.)
Thrust needle roller bearing (F) 28.7 mm (1.130 in.) 53.8 mm (2.118 in.)


Text in Illustration
*1 Thrust Needle Roller Bearing
*2 Thrust Bearing Race

NOTICE:

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.



Hide 35760 12.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
C336524E01
2.366,0.1 2.578,0.279 0.211,0.179 10 *1 2.542,0.7 2.753,0.879 0.211,0.179 10 *2 2.637,1.255 2.849,1.435 0.211,0.179 10 *3 1.862,0.192 2.361,0.192 false 2.172,0.788 2.521,0.788 false 1.864,1.759 2.412,1.342 2.412,1.342 2.63,1.342 false

Install the thrust bearing race, rear planetary gear assembly and thrust needle roller bearing to the automatic transmission case sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
for Front Side
Thrust bearing race (F)
31.5 mm (1.240 in.) 57.3 mm (2.256 in.)
Thrust needle roller bearing (E) 31.0 mm (1.221 in.) 53.7 mm (2.114 in.)


Text in Illustration
*1 Thrust Needle Roller Bearing
*2 Rear Planetary Gear Assembly
*3 Thrust Bearing Race

NOTICE:
·

Before installing the rear planetary gear assembly, apply ATF to the sliding surfaces of the rear planetary gear assembly bush. After the installation, check that the rear planetary gear assembly rotates smoothly.

·

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.




Hide 35707D 13.INSTALL REAR PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C336495E01
2.428,0.079 2.600,0.255 0.172,0.177 10 *1 2.845,0.566 3.037,0.749 0.192,0.183 10 *2 1.896,0.443 2.259,0.164 2.259,0.164 2.405,0.164 false 1.899,1.428 2.682,0.658 2.682,0.658 2.828,0.658 false

Install the thrust bearing race and rear planetary sun gear sub-assembly to the automatic transmission case sub-assembly.

Standard Thrust Bearing Race Diameter:
Item Inside Outside
Thrust bearing race (E) 30.0 mm (1.181 in.) 49.9 mm (1.965 in.)


Text in Illustration
*1 Rear Planetary Sun Gear Sub-assembly
*2 Thrust Bearing Race (E)

NOTICE:
·

Before installing the rear planetary sun gear sub-assembly, apply ATF to the sliding surfaces of the rear planetary sun gear sub-assembly bush. After the installation, check that the rear planetary sun gear sub-assembly rotates smoothly.

·

Use a small amount of MP grease to make the thrust bearing race stay securely in place.




Hide 35682A 14.INSTALL NO. 2 BRAKE DISC SET

a.
C336525E01
0.417,2.637 0.597,2.807 0.180,0.170 10 *1 0.628,0.173 0.811,0.345 0.182,0.172 10 *4 1.27,2.714 0.629,2.714 false 2.703,0.353 2.898,0.523 0.195,0.170 10 *2 2.126,0.436 2.679,0.436 false 2.131,2.549 2.425,2.549 2.425,2.549 2.425,0.439 false 2.13,0.847 2.423,0.847 false 2.117,1.25 2.423,1.25 false 2.129,1.689 2.43,1.689 false 2.131,2.082 2.425,2.082 false 0.519,2.222 0.714,2.392 0.195,0.170 10 *3 1.276,2.307 0.74,2.307 false 1.268,0.694 0.948,0.694 0.948,0.694 0.948,2.302 false 1.268,1.098 0.948,1.098 false 1.265,1.511 0.945,1.511 false 1.268,1.926 0.948,1.926 false 1.261,0.258 0.843,0.258 false

Install the No. 2 brake flange, 6 No. 2 brake discs, 5 No. 2 brake plates and brake plate to the automatic transmission case sub-assembly.

Install in order:

*4 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


Text in Illustration
*1 Brake Plate
*2 No. 2 Brake Disc
*3 No. 2 Brake Plate
*4 No. 2 Brake Flange

NOTICE:

Make sure that the No. 2 brake discs, No. 2 brake plates, brake plate and No. 2 brake flange are installed in the correct order.


HINT:

Assemble the automatic transmission case sub-assembly, No. 2 brake flange, No. 2 brake plate and brake plate by aligning their grooves as shown in the illustration.

C336526E04
1.021,0.375 1.177,0.375 1.177,0.375 1.677,0.969 false 4.01,0.594 4.188,0.594 4.188,0.594 4.448,0.802 false 6.063,2 5.865,2 5.865,2 5.521,1.594 false 0.844,0.281 1.031,0.469 0.188,0.188 10 false *a 3.823,0.51 4.021,0.708 0.198,0.198 10 false *a 6.083,1.927 6.281,2.115 0.198,0.188 10 false *1

Text in Illustration
*1 Brake Plate, No. 2 Brake Plate and No. 2 Brake Flange - -
*a Groove - -



b.

Install the snap ring to the automatic transmission case sub-assembly.


Hide 35791A 15.INSTALL NO. 1 ONE-WAY CLUTCH

a.
C344388E01
2.602,0.572 2.758,0.753 0.156,0.181 10 *2 2.85,1.203 3.006,1.384 0.156,0.181 10 *3 2.602,1.69 2.758,1.871 0.156,0.181 10 *1 2.17,0.663 2.577,0.663 false 2.162,1.776 2.577,1.776 false 2.414,1.299 2.826,1.299 false

Install the No. 1 one-way clutch to the one-way clutch outer race with the snap ring.

Text in Illustration
*1 Snap Ring
*2 No. 1 One-way Clutch
*3 One-way Clutch Outer Race

NOTICE:

Make sure that the No. 1 one-way clutch is oriented correctly.



Hide 35795 17.INSTALL ONE-WAY CLUTCH OUTER RACE WITH NO. 1 ONE-WAY CLUTCH

a.
C336528

Install the one-way clutch outer race with No. 1 one-way clutch to the automatic transmission case sub-assembly.


b.
C336496E05
1.594,0.177 2.625,0.177 true 2.667,0.094 3.01,0.292 0.344,0.198 10 true SST

Using SST, install the snap ring to the automatic transmission case sub-assembly.

SST
09350-30020  (09350-07060)

NOTICE:
C336527

Install the snap ring so that its end gap will be within the range shown in the illustration.



Hide 35709J 18.INSTALL SUN GEAR INPUT DRUM SUB-ASSEMBLY

a.
C336494E01
2.555,0.317 2.730,0.487 0.175,0.170 10 *1 2.45,0.814 2.627,0.989 0.177,0.175 10 *2 2.476,1.255 2.651,1.428 0.175,0.173 10 *3 1.944,1.66 2.313,1.344 2.313,1.344 2.454,1.344 false 1.941,1.243 2.283,0.908 2.283,0.908 2.423,0.908 false 2.19,0.403 2.538,0.403 false

Install the thrust bearing race, thrust needle roller bearing and sun gear input drum sub-assembly to the automatic transmission case sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
Thrust bearing race (D) 71.9 mm (2.831 in.) 87.8 mm (3.457 in.)
Thrust needle roller bearing (D) 71.2 mm (2.803 in.) 84.5 mm (3.327 in.)


Text in Illustration
*1 Sun Gear Input Drum Sub-assembly
*2 Thrust Needle Roller Bearing (D)
*3 Thrust Bearing Race (D)

NOTICE:
·

Before installing the sun gear input drum sub-assembly, apply ATF to the sliding surfaces of the sun gear input drum sub-assembly bush. After the installation, check that the sun gear input drum sub-assembly rotates smoothly.

·

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.




Hide 35612B 19.INSTALL FORWARD CLUTCH PISTON

a.

Coat 2 new O-rings with ATF, and install them to the forward clutch piston.


b.
C150419E01
2.775,0.543 2.966,0.734 0.191,0.191 10 *1 2.416,0.632 2.754,0.632 false

Install the forward clutch piston to the forward clutch drum sub-assembly.

Text in Illustration
*1 Forward Clutch Piston


c.

Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.


d.
C148187E01
2.692,0.252 2.848,0.433 0.156,0.181 10 *1 2.692,0.89 2.848,1.072 0.156,0.181 10 *2 2.209,0.354 2.644,0.354 false 2.117,0.985 2.644,0.985 false

Install the forward clutch return spring sub-assembly and No. 1 clutch balancer to the forward clutch drum sub-assembly.

Text in Illustration
*1 No. 1 Clutch Balancer
*2 Forward Clutch Return Spring Sub-assembly


e.
C336491E01
0.046,0.32 0.369,0.518 0.323,0.198 10 SST 1.485,0.349 0.447,0.416 0.447,0.416 0.994,1.21 false

Set SST on the No. 1 clutch balancer, tighten SST and compress the No. 1 clutch balancer.

SST
09380-50010  (09381-05010, 09381-05020, 09381-05030, 09381-05040, 09381-05050)

NOTICE:

Stop pressing when the balancer is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent spring sheet deformation.



f.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




Hide 35633B 20.INSTALL FORWARD MULTIPLE CLUTCH DISC SET

a.
C336492E01
1.871,0.013 2.046,0.201 0.174,0.188 10 *1 1.885,0.464 2.059,0.653 0.174,0.188 10 *2 0.026,2.801 0.201,2.989 0.174,0.188 10 *3 1.361,0.23 1.601,0.092 1.601,0.092 1.851,0.092 false 1.365,0.548 1.859,0.548 false 1.364,2.43 1.61,2.43 1.61,2.43 1.61,0.55 false 1.365,2.112 1.611,2.112 false 1.368,1.8 1.614,1.8 false 1.369,1.488 1.615,1.488 false 1.371,1.167 1.617,1.167 false 1.368,0.866 1.614,0.866 false 0.334,0.718 0.141,0.718 0.141,0.718 0.141,2.791 false 0.332,1.002 0.14,1.002 false 0.33,1.307 0.137,1.307 false 0.337,1.633 0.144,1.633 false 0.33,1.938 0.137,1.938 false 0.332,2.252 0.14,2.252 false 0.337,2.557 0.144,2.557 false

Install the 7 forward multiple clutch plates, 7 forward multiple clutch discs and forward clutch flange to the forward clutch drum sub-assembly.

Install in order:

*3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


Text in Illustration
*1 Forward Clutch Flange
*2 Forward Multiple Clutch Disc
*3 Forward Multiple Clutch Plate

NOTICE:

Make sure that the forward multiple clutch discs, forward multiple clutch plates and the forward clutch flange are installed in the correct order.



b.
C150420E01
2.643,0.321 2.840,0.505 0.198,0.184 10 *1 2.628,0.408 2.364,0.408 2.364,0.408 1.978,0.795 false

Install the snap ring to the forward clutch drum sub-assembly.

Text in Illustration
*1 Snap Ring


Hide 35633B 21.INSPECT PACK CLEARANCE OF FORWARD MULTIPLE CLUTCH

Hide 35743 22.INSTALL FRONT PLANETARY RING GEAR

a.
C150421E01
0.994,1.582 1.187,1.922 1.187,1.922 1.399,1.922 false 1.449,1.823 1.605,2.004 0.156,0.181 10 *1 1.806,1.33 2,1.67 2,1.67 2.212,1.67 false 2.262,1.571 2.417,1.753 0.156,0.181 10 *2 2.617,1.213 2.811,1.553 2.811,1.553 3.023,1.553 false 3.072,1.454 3.228,1.635 0.156,0.181 10 *3

Using needle-nose pliers, install the snap ring to the groove of forward multiple disc clutch assembly.

Text in Illustration
*1 Front Planetary Ring Gear
*2 Snap Ring
*3 Forward Multiple Disc Clutch Assembly


b.
C151056

Using needle-nose pliers, contract the snap ring and install the front planetary ring gear to the forward multiple disc clutch assembly.

NOTICE:

Confirm that the snap ring is correctly located in the groove of the forward multiple disc clutch assembly as shown in the illustration.



Hide 35631 23.INSTALL FORWARD MULTIPLE DISC CLUTCH HUB

a.
C151065E02
2.08,1.827 2.245,1.976 0.165,0.149 10 *2 1.19,0.687 1.356,0.836 0.165,0.149 10 *1 2.292,1.432 2.457,1.581 0.165,0.149 10 *3 2.916,0.206 3.082,0.355 0.165,0.149 10 *4 0.939,1.025 0.991,0.782 0.991,0.782 1.117,0.782 false 2.686,0.55 2.738,0.307 2.738,0.307 2.864,0.307 false 2.057,1.279 2.11,1.522 2.11,1.522 2.236,1.522 false 1.786,1.371 1.908,1.911 1.908,1.911 2.034,1.911 false

Install the thrust needle roller bearing, thrust bearing race and forward multiple disc clutch assembly with front planetary ring gear to the forward multiple disc clutch hub.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
Thrust needle roller bearing (B) 34.5 mm (1.358 in.) 49.9 mm (1.965 in.)
Thrust bearing race (B) 36.6 mm (1.441 in.) 51.9 mm (2.043 in.)


Text in Illustration
*1 Forward Multiple Disc Clutch Assembly with Front Planetary Ring Gear
*2 Thrust Needle Roller Bearing (B)
*3 Thrust Bearing Race (B)
*4 Forward Multiple Disc Clutch Hub

NOTICE:

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.



Hide 35601E 24.INSTALL FORWARD MULTIPLE DISC CLUTCH ASSEMBLY WITH FRONT PLANETARY RING GEAR AND FORWARD MULTIPLE DISC CLUTCH HUB

a.
C336490E01
2.085,0.342 2.543,0.342 false 2.559,0.259 2.740,0.436 0.181,0.177 10 *1 2.629,0.639 2.785,0.821 0.156,0.181 10 *2 2.629,0.919 2.785,1.100 0.156,0.181 10 *3 1.836,1.151 2.432,0.735 2.432,0.735 2.6,0.735 false 1.836,1.415 2.431,0.995 2.431,0.995 2.599,0.995 false

Install the thrust bearing race, thrust needle roller bearing and forward multiple disc clutch assembly with front planetary ring gear and forward multiple disc clutch hub to the automatic transmission case sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
Thrust needle race (C) 47.0 mm (1.850 in.) 61.9 mm (2.437 in.)
Thrust bearing roller bearing (C) 46.5 mm (1.831 in.) 60.1 mm (2.366 in.)


Text in Illustration
*1 Forward Multiple Disc Clutch Assembly with Front Planetary Ring Gear
*2 Thrust Bearing Race (C)
*3 Thrust Needle Roller Bearing (C)

NOTICE:
·

Before installing the forward multiple disc clutch assembly, apply ATF to the sliding surfaces of the forward multiple disc clutch assembly bush. After the installation, check that the forward multiple disc clutch assembly rotates smoothly.

·

Use a small amount of MP grease to make the thrust needle roller bearing and thrust needle roller bearing race stay securely in place.




Hide 35048 25.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

a.

Coat a new O-ring with ATF, and install it to the reverse clutch drum sub-assembly.


b.
C337018E01
2.585,0.467 2.797,0.672 0.211,0.205 10 *1 2.195,0.549 2.573,0.549 false

Install the reverse clutch piston sub-assembly to the reverse clutch drum sub-assembly.

Text in Illustration
*1 Reverse Clutch Piston Sub-assembly


c.

Coat a new O-ring with ATF, and install it to the No. 3 clutch balancer.


d.
C336486E01
2.721,0.226 2.900,0.406 0.179,0.180 10 *1 2.657,0.786 2.843,0.963 0.186,0.177 10 *2 2.18,0.313 2.696,0.313 false 2.116,0.874 2.632,0.874 false

Install the reverse clutch return spring sub-assembly (front) and No. 3 clutch balancer to the reverse clutch drum sub-assembly.

Text in Illustration
*1 No. 3 Clutch Balancer
*2 Reverse Clutch Return Spring Sub-assembly (Front)


e.
C336485E01
0.563,1.644 0.876,1.824 0.312,0.180 10 SST 1.481,0.952 0.954,1.704 0.954,1.704 2.074,1.176 false

Set SST on the No. 3 clutch balancer, tighten SST and compress the No. 3 clutch balancer.

SST
09380-50010  (09381-05010, 09381-05020, 09381-05030, 09381-05040, 09381-05050)

NOTICE:

Stop pressing when the balancer is lowered to the place 1.0 to 2.0 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent spring sheet deformation.



f.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




Hide 34601 26.INSTALL OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.

Coat 3 new O-rings with ATF, and install them to the overdrive direct clutch drum sub-assembly.


b.
C337016E01
2.524,0.433 2.703,0.616 0.179,0.183 10 *1 2.221,0.517 2.511,0.517 false

Install the overdrive direct clutch drum sub-assembly to the reverse clutch drum sub-assembly.

Text in Illustration
*1 Overdrive Direct Clutch Drum Sub-assembly


Hide 34638 27.INSTALL NO. 4 CLUTCH PISTON

a.

Coat a new O-ring with ATF, and install it to the No. 4 clutch piston.


b.
C337017E01
2.447,0.343 2.668,0.549 0.221,0.207 10 *1 2.108,0.427 2.432,0.427 false

Install the No. 4 clutch piston to the overdrive direct clutch drum sub-assembly.

Text in Illustration
*1 No. 4 Clutch Piston


c.
C336482E01
2.5,0.176 2.683,0.355 0.183,0.179 10 *1 2.002,0.26 2.48,0.26 false 1.988,0.712 2.467,0.712 false 2.495,0.622 2.681,0.803 0.186,0.181 10 *2

Install the reverse clutch return spring sub-assembly (rear) and reverse clutch balancer to the overdrive direct clutch drum sub-assembly.

Text in Illustration
*1 Reverse Clutch Balancer
*2 Reverse Clutch Return Spring Sub-assembly (Rear)


d.
C336481E01
0.085,0.314 0.392,0.507 0.307,0.192 10 SST 1.552,0.462 0.476,0.405 0.476,0.405 1.052,1.351 false

Set SST on the reverse clutch balancer, tighten SST and compress the reverse clutch balancer.

SST
09380-50010  (09381-05010, 09381-05020, 09381-05030, 09381-05040, 09381-05050)

NOTICE:

Stop pressing when the balancer is lowered to the place 1.0 to 2.0 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent spring sheet deformation.



e.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:
·

Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

·

Do not expand the snap ring excessively.




Hide 35633D 28.INSTALL OVERDRIVE DIRECT CLUTCH DISC

a.
C336489E01
1.396,0.323 1.688,0.073 1.688,0.073 1.875,0.073 false 1.438,0.552 1.885,0.552 false 1.438,2.417 1.635,2.417 1.635,2.417 1.635,0.552 false 1.438,0.948 1.635,0.948 false 1.438,1.313 1.635,1.313 false 1.438,1.688 1.635,1.688 false 1.438,2.031 1.635,2.031 false 0.458,2.656 0.208,2.656 false 0.448,0.76 0.302,0.76 0.302,0.76 0.302,2.656 false 0.448,1.115 0.302,1.115 false 0.448,1.49 0.302,1.49 false 0.448,1.854 0.302,1.854 false 0.448,2.219 0.302,2.219 false 1.896,0 2.083,0.188 0.188,0.188 10 false *1 1.906,0.469 2.094,0.656 0.188,0.188 10 false *2 0.01,2.563 0.188,2.74 0.177,0.177 10 false *3

Install the 6 overdrive direct clutch plates, 6 overdrive direct clutch discs and overdrive clutch flange to the overdrive direct clutch drum sub-assembly.

Install in order:

*3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


Text in Illustration
*1 Overdrive Clutch Flange
*2 Overdrive Direct Clutch Disc
*3 Overdrive Direct Clutch Plate

NOTICE:

Make sure that the overdrive direct clutch discs, overdrive direct clutch plates and the overdrive clutch flange are installed in the correct order.



b.
C337014E01
2.345,0.132 2.556,0.329 0.211,0.198 10 *1 2.326,0.213 2.124,0.213 2.124,0.213 1.755,0.691 false

Install the snap ring to the overdrive direct clutch drum sub-assembly.

Text in Illustration
*1 Snap Ring


Hide 35677J 30.INSTALL NO. 3 CLUTCH DISC SET

a.
C336488E01
1.959,0 2.191,0.205 0.232,0.205 10 *1 2.047,0.423 2.279,0.628 0.232,0.205 10 *2 0.001,2.1 0.171,2.271 0.171,0.171 10 *3 0.14,2.978 0.329,3.160 0.188,0.181 10 *4 1.94,0.067 1.687,0.067 1.687,0.067 1.442,0.2 false 1.503,0.547 1.972,0.547 false 1.498,2.378 1.653,2.378 1.653,2.378 1.653,0.548 false 1.5,0.933 1.659,0.933 false 1.497,1.286 1.656,1.286 false 1.497,1.65 1.656,1.65 false 1.498,2.002 1.657,2.002 false 0.354,3.062 0.483,3.062 0.483,3.062 0.655,2.827 false 0.381,2.181 0.188,2.181 false 0.262,2.178 0.262,0.74 0.262,0.74 0.374,0.74 false 0.264,1.093 0.376,1.093 false 0.269,1.445 0.38,1.445 false 0.267,1.808 0.378,1.808 false

Install the 6 No. 3 clutch plates, 6 No. 3 clutch discs and No. 3 clutch flange to the reverse clutch drum sub-assembly.

Install in order:

*4 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *1


No. 3 Clutch Plate Thickness:
Item Thickness
No. 3 Clutch Plate (A) 1.8 mm (0.0709 in.)
No. 3 Clutch Plate (B) 3.5 mm (0.138 in.)


Text in Illustration
*1 No. 3 Clutch Flange
*2 No. 3 Clutch Discs
*3 No. 3 Clutch Plate (A)
*4 No. 3 Clutch Plate (B)

NOTICE:

Make sure that the No. 3 clutch discs, No. 3 clutch plates and the No. 3 clutch flange are installed in the correct order.



b.
C337013E01
2.377,0.27 2.565,0.447 0.188,0.177 10 *1 2.36,0.356 2.14,0.356 2.14,0.356 1.833,0.705 false

Install the snap ring to the reverse clutch drum sub-assembly.

Text in Illustration
*1 Snap Ring


Hide 35720 32.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C293402E01
1.151,0.464 1.348,0.652 0.198,0.188 10 *1 1.129,0.548 0.9,0.548 0.9,0.548 0.588,1.186 false

Install the front planetary gear radial needle roller bearing to the front planetary gear assembly.

Text in Illustration
*1 Front Planetary Gear Radial Needle Roller Bearing

NOTICE:

Do not expand the front planetary gear radial needle roller bearing excessively.



b.
C148182E05
2.021,1.365 2.073,1.719 2.073,1.719 2.354,1.458 false 2.01,1.792 2.313,2 0.302,0.208 10 false *1

Coat 2 new oil seal rings with ATF, and install them to the front planetary gear assembly.

Text in Illustration
*1 Oil Seal Ring

NOTICE:

Do not expand the oil seal ring ends excessively.



c.
C148181E02
0.664,1.535 0.664,1.85 0.664,1.85 1.566,1.85 false 0.807,1.494 0.807,1.851 false 0.943,1.458 0.943,1.852 false 1.584,1.759 1.789,1.931 0.205,0.172 10 *1

Coat 3 new oil seal rings with ATF, and install them to the front planetary gear assembly.

Text in Illustration
*1 Oil Seal Ring

NOTICE:

Do not expand the oil seal ring ends excessively.



d.
C148180E01
1.177,0.497 1.375,0.671 0.198,0.174 10 *1 1.159,0.582 0.921,0.582 0.921,0.582 0.575,1.132 false

Install the planetary carrier thrust washer to the front planetary gear assembly.

Text in Illustration
*1 Planetary Carrier Thrust Washer

NOTICE:

Use a small amount of MP grease to make the planetary carrier thrust washer stay securely in place.



e.
C148179E01
0.988,0.473 1.208,0.675 0.221,0.202 10 *1 0.517,1.202 0.784,0.561 0.784,0.561 0.973,0.561 false

Install the front planetary sun gear to the front planetary gear assembly.

Text in Illustration
*1 Front Planetary Sun Gear


f.
C336478E01
2.034,1.57 2.236,1.758 0.202,0.188 10 *1 2.159,0.999 2.159,1.553 false

Assemble the front planetary gear assembly together with the front planetary sun gear to the overdrive and reverse multiple disc clutch assembly.

Text in Illustration
*1 Front Planetary Gear Assembly


Hide 34.INSTALL OVERDRIVE AND REVERSE MULTIPLE DISC CLUTCH ASSEMBLY AND FRONT PLANETARY GEAR ASSEMBLY

a.
C337015E01
1.782,0.231 2.351,0.231 false 2.366,0.146 2.533,0.311 0.168,0.165 10 *1 2.65,0.984 2.805,1.165 0.156,0.181 10 *2 0.562,1.024 0.743,1.200 0.181,0.177 10 *3 1.851,1.598 2.455,1.076 2.455,1.076 2.588,1.076 false 1.583,1.841 0.899,1.108 0.899,1.108 0.766,1.108 false

Install the thrust bearing race, thrust needle roller bearing, and overdrive and reverse multiple disc clutch assembly and front planetary gear assembly to the automatic transmission case sub-assembly.

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter:
Item Inside Outside
Thrust needle roller bearing (A) 36.2 mm (1.425 in.) 58.2 mm (2.291 in.)
Thrust bearing race (A) 44.0 mm (1.732 in.) 62.0 mm (2.441 in.)


Text in Illustration
*1 Overdrive and Reverse Multiple Disc Clutch Assembly and Front Planetary Gear Assembly
*2 Thrust Needle Roller Bearing (A)
*3 Thrust Bearing Race (A)

NOTICE:
·

Before installing the reverse clutch drum sub-assembly, apply ATF to the sliding surfaces of the reverse clutch drum sub-assembly. After the installation, check that the overdrive direct clutch drum sub-assembly rotates smoothly.

·

Use a small amount of MP grease to make the thrust bearing and thrust bearing race stay securely in place.




b.

Install the snap ring to the automatic transmission case sub-assembly.


Hide 35681A 35.INSTALL NO. 1 BRAKE DISC SET

a.
C336979E01
2.152,2.36 2.711,2.36 false 2.151,0.319 2.712,0.319 false 2.154,2.023 2.524,2.023 2.524,2.023 2.524,0.319 false 2.145,0.684 2.524,0.684 false 2.143,1.019 2.524,1.019 false 2.73,2.27 2.907,2.446 0.177,0.176 10 *1 2.731,0.23 2.931,0.406 0.200,0.177 10 *3 0.466,0.37 0.622,0.551 0.156,0.181 10 *2 1.301,0.461 0.671,0.461 false 1.301,2.169 0.892,2.169 0.892,2.169 0.892,0.461 false 1.302,0.818 0.892,0.818 false 1.302,1.152 0.892,1.152 false 1.302,1.504 0.888,1.504 false 1.304,1.831 0.89,1.831 false 2.143,1.35 2.524,1.35 false 2.148,1.685 2.528,1.685 false

Install the selected No. 1 brake flange, 6 No. 1 brake discs and 6 No. 1 brake plates to the automatic transmission case sub-assembly.

Install in order:

*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3


Text in Illustration
*1 No. 1 Brake Flange
*2 No. 1 Brake Disc
*3 No. 1 Brake Plate

NOTICE:

Make sure that the No. 1 brake discs, No. 1 brake plates and the No. 1 brake flange are installed in the correct order.



Hide 34629 36.INSTALL OVERDRIVE BRAKE PLATE STOPPER SPRING

a.
C341795

Install the overdrive brake plate stopper spring to the automatic transmission case sub-assembly as shown in the illustration.

NOTICE:

Install the overdrive brake plate stopper spring so that the wider side is facing inwards.



Hide 37.INSTALL OIL PUMP ASSEMBLY

a.
C329086E01
0.811,1.778 1.008,1.961 0.198,0.184 10 *1 3.062,0.048 3.255,0.236 0.193,0.188 10 *2 0.935,1.544 0.935,1.767 false 2.717,0.435 2.918,0.134 2.918,0.134 3.05,0.134 false

Coat a new oil pump O-ring with ATF, and install it to the oil pump assembly.

Text in Illustration
*1 Oil Pump Assembly
*2 Oil Pump O-ring


b.

Clean and degrease the threads of the 11 bolts and the contact surfaces of the automatic transmission case sub-assembly and the oil pump assembly with non-residue solvent.

NOTICE:

During installation, do not allow oil to contact the bolts or the surface of the oil pump assembly body.



c.

Place the oil pump assembly through the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.


d.

Hold the input shaft, and lightly press the oil pump assembly to slide the oil seal rings into the front planetary gear assembly.

NOTICE:

Be careful not to damage the O-ring and oil seal rings.



e.
C336473

Install the 11 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 35409D 39.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C344393E01
2.224,0.698 2.413,0.874 0.189,0.176 10 *1 0.989,1.023 1.178,1.199 0.189,0.176 10 *2 1.853,0.784 2.214,0.784 false 1.205,1.103 1.319,1.103 1.319,1.103 1.711,1.322 false

Install the manual detent spring sub-assembly and manual detent spring cover with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Manual Detent Spring Sub-assembly
*2 Manual Detent Spring Cover


Hide 35506F 40.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C336466E03
1.115,0.406 1.438,0.406 1.438,0.406 1.719,0.813 true 0.917,2.844 1.24,2.844 1.24,2.844 1.521,3.25 true 0.729,0.333 1.052,0.531 0.323,0.198 10 true SST 0.573,2.781 0.896,3.052 0.323,0.271 10 true SST 0.021,0.021 0.24,0.229 0.219,0.208 10 false *A 0.021,2.24 0.24,2.448 0.219,0.208 10 false *B

Using SST and a hammer, tap in 2 new manual valve lever shaft oil seals.

SST
09350-30020  (09350-07110)

Standard depth:

-0.2 to 0.4 mm (-0.00788 to 0.0157 in.)


Text in Illustration
*A for RH Side
*B for LH Side


b.

Coat the lip of the 2 manual valve lever shaft oil seals with MP grease.


Hide 35556 41.INSTALL PARKING LOCK PAWL SHAFT

a.
U156480E01
2.302,0.375 2.563,0.188 2.563,0.188 2.719,0.188 false 1.302,1.198 0.854,1.604 0.854,1.604 0.854,1.75 true 0.344,1.49 0.458,1.49 0.458,1.49 0.615,1.188 true 1.521,1.281 1.521,1.667 true 2.729,0.104 2.927,0.281 0.198,0.177 10 false *1 0.74,1.76 0.938,1.938 0.198,0.177 10 false *2 0.125,1.406 0.313,1.583 0.188,0.177 10 false *3 1.458,1.698 1.635,1.875 0.177,0.177 10 false *4

Install the E-ring to the parking lock pawl shaft.

Text in Illustration
*1 Parking Lock Pawl
*2 Parking Lock Pawl Shaft
*3 Spring
*4 E-ring


b.

Install the parking lock pawl, parking lock pawl shaft and spring.


Hide 35501 42.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C336467E01
1.73,1.166 1.912,1.340 0.181,0.174 10 *1 2.738,1.171 2.919,1.346 0.181,0.174 10 *2 1.944,1.245 2.024,1.245 2.024,1.245 2.177,1.454 false 2.727,1.258 2.645,1.258 2.645,1.258 2.47,1.623 false

Connect the parking lock rod sub-assembly to the manual valve lever sub-assembly.

Text in Illustration
*1 Manual Valve Lever Sub-assembly
*2 Parking Lock Rod Sub-assembly


Hide 35505 43.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.
C336468E01
0.103,1.042 0.281,1.210 0.177,0.168 10 *1 0.771,1.127 0.302,1.127 false

Install a new spacer to the manual valve lever sub-assembly.

Text in Illustration
*1 Spacer


b.

Install the manual valve lever shaft to the manual valve lever sub-assembly and automatic transmission case sub-assembly.


c.
U156482E01
2.027,0.434 2.239,0.618 0.211,0.184 10 *1 1.668,1.133 1.926,0.52 1.926,0.52 2.016,0.52 false

Using a hammer, install a new spring pin.

Text in Illustration
*1 Spring Pin


d.

Turn the spacer and manual valve lever shaft to align the smaller hole on the spacer with the indent on the manual valve lever sub-assembly.


e.
C336463

Using a 3 mm pin punch and a hammer, stake the spacer.


f.

Check that the spacer does not turn.


Hide 35595 44.INSTALL PARKING LOCK PAWL BRACKET

a.
U156479E04
0.698,0.51 0.813,0.698 0.115,0.188 10 false 1 0.844,1.917 0.979,2.115 0.135,0.198 10 false 2 2.417,0.208 2.552,0.406 0.135,0.198 10 false 3

Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts, in several steps in the order shown in the illustration.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.
C341796

Move the manual valve lever sub-assembly to the P position, and check the output shaft sub-assembly is locked by the parking lock pawl.


Hide 35106 49.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35141B 50.INSTALL AUTOMATIC TRANSMISSION CASE PLUG

a.
C341793E01
0.052,0.042 0.271,0.26 0.219,0.219 10 false *A 0.052,2.396 0.271,2.615 0.219,0.219 10 false *B

for T55H "TORX" Type:

Text in Illustration
*A for LH Side
*B for Rear Side

i.

Install the 2 new O-rings to the 2 automatic transmission case plugs.


ii.

Using a T55H "TORX" socket wrench, install the 2 automatic transmission case plugs to the automatic transmission case sub-assembly.

Torque:
40 N*m (403 kgf*cm, 30 ft.*lbf)



b.
C336459

for 17 mm Hexagon Type:

i.

Install a new O-ring to the automatic transmission case plug.


ii.

Install the automatic transmission case plug to the automatic transmission case sub-assembly.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)



Hide 35141B 51.INSTALL REFILL PLUG

a.

Install a new O-ring to the refill plug.


b.

Install the refill plug.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 52.INSTALL OIL COOLER TUBE UNION

a.

Install the 2 new O-rings to the 2 oil cooler tube unions.


b.
C336457E01
1.938,1.302 0.635,2.25 0.635,2.25 0.49,2.25 true 2.417,2.26 2.615,2.448 0.198,0.188 10 false *a 0.542,1.281 0.74,1.469 0.198,0.188 10 false *b 1.198,1.229 1.396,1.417 0.198,0.188 10 false *c 0.177,2.167 0.5,2.344 0.323,0.177 10 false SST

Using SST, install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.

SST
09268-78010  

Torque:
Specified tightening torque : 29 N*m (300 kgf*cm, 22 ft.*lbf)

Text in Illustration
*a Torque Wrench Fulcrum Length
*b 18 to 22°
*c 43 to 47°

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When using SST (fulcrum length of 34.5 mm (1.3583 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 25 N*m (252 kgf*cm, 18 ft.*lbf)




Hide 35015G 54.INSTALL REAR TRANSFER ADAPTER

a.

Coat a new O-ring with ATF and install it to the rear transfer adapter.


b.
C336500

Install the rear transfer adapter with the 10 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)


Hide 35015J 55.INSTALL TRANSFER CASE ADAPTER REAR OIL SEAL

a.

Coat the lip of a new transfer case adapter rear oil seal with MP grease.


b.
C336502E01
0.11,0.263 0.432,0.450 0.323,0.187 10 SST 0.493,0.34 0.691,0.34 0.691,0.34 1.159,0.517 false 0.691,0.34 1.069,1.101 false

Using SST and a hammer, tap in the transfer case adapter rear oil seal.

SST
09223-50010  
09710-30031  (09710-03171)

Standard depth:

0 to 1 mm (0 to 0.0393 in.)



Hide 35111 56.INSTALL AUTOMATIC TRANSMISSION HOUSING

a.
C336472

Remove the automatic transmission assembly from the overhaul attachment.


b.
C336471

Install the automatic transmission housing to the automatic transmission case sub-assembly with the 16 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 57.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C337012E01
1.024,0.165 1.220,0.331 0.195,0.166 10 *1 1.011,0.246 0.865,0.246 0.865,0.246 0.633,0.515 false 3.138,1.058 3.333,1.225 0.195,0.166 10 *2 3.123,1.144 2.986,1.144 2.986,1.144 2.84,1.419 false 0.603,1.627 0.778,1.807 0.176,0.180 10 *3 0.805,1.714 1,1.714 1,1.714 1.223,1.379 false 1.898,0.417 2.073,0.596 0.176,0.180 10 *4 1.876,0.502 1.738,0.502 1.738,0.502 1.443,0.794 false 2.011,0.997 2.186,1.176 0.176,0.180 10 *5 2.21,1.081 2.374,1.081 2.374,1.081 2.591,1.318 false

Coat a new breather plug O-ring with ATF, and install it to the No. 1 breather plug.

Text in Illustration
*1 No. 2 Breather Plug
*2 No. 1 Breather Plug
*3 Breather Plug Hose
*4 Clamp
*5 Breather Plug O-ring

NOTICE:

Ensure that the breather plug O-ring is not twisted.



b.

Install the No. 1 breather plug and No. 2 breather plug to the breather plug hose.


c.

Install the clamp to the breather plug hose.


d.
C336458

Install the transmission breather hose sub-assembly to the automatic transmission case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)