Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17A9  Transfer Shift Motor Control Circuit Low  


DESCRIPTION

This DTC is output when a short to ground in the high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* drive circuit is detected.

*: w/ Rear Differential Lock


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17A9
1.

While the ignition switch is turned to ON or directly after the ignition switch is turned to ON (high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* not operating)

2.

Short to ground in the high-low transfer shift motor, center differential lock shift motor and differential lock shift motor* drive circuit

3.

0.5 seconds or more (if directly after ignition switch is turned ON, 0.05 seconds or more)

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly

·

Differential lock shift actuator*



*: w/ Rear Differential Lock


WIRING DIAGRAM

C341640E02
3.979,7.417 4.313,7.646 0.333,0.229 10 false A28 4.375,7.417 6.146,7.573 1.771,0.156 10 false 4 Wheel Drive Control ECU 4.396,2.063 4.917,2.344 0.521,0.281 10 false TM1 4.375,2.74 4.896,3.021 0.521,0.281 10 false TM2 4.167,2.063 4.531,2.354 0.365,0.292 10 false 8 4.167,2.719 4.531,3.01 0.365,0.292 10 false 7 2.115,1.292 2.635,1.573 0.521,0.281 10 false TM1 2.135,1.958 2.656,2.24 0.521,0.281 10 false TM2 2.531,1.385 2.927,1.594 0.396,0.208 10 false C37 2.542,2.052 2.938,2.26 0.396,0.208 10 false C37 0.604,3.75 1.802,4.396 1.198,0.646 10 false High-low Transfer Shift Motor 0.542,1.573 1.729,2.083 1.188,0.51 10 false Center Differential Lock Shift Motor 0.552,4.646 2.292,4.865 1.74,0.219 10 false High-low Transfer Actuator 0.344,2.51 2.469,3.021 2.125,0.51 10 false Center Differential Lock Actuator 0.448,5.125 2.729,5.333 2.281,0.208 10 false Transfer Shift Actuator Assembly 0.594,7.115 2.708,7.354 2.115,0.24 10 false Differential Lock Shift Actuator* 0.615,6.01 1.792,6.552 1.177,0.542 10 false Differential Lock Shift Motor 0.188,7.375 1.927,7.604 1.74,0.229 10 false *: w/ Rear Differential Lock 4.354,3.458 4.875,3.74 0.521,0.281 10 false HM1 4.385,4.156 4.906,4.438 0.521,0.281 10 false HM2 4.188,3.458 4.448,3.656 0.26,0.198 10 false 2 4.198,4.156 4.563,4.448 0.365,0.292 10 false 6 2.531,3.583 2.927,3.792 0.396,0.208 10 false C38 2.531,4.25 2.927,4.458 0.396,0.208 10 false C38 0.406,7.115 0.646,7.292 0.24,0.177 10 false f1 4.385,4.833 4.906,5.115 0.521,0.281 10 false M1 4.365,5.49 4.885,5.771 0.521,0.281 10 false M2 4.177,4.833 4.344,5.01 0.167,0.177 10 false 3 4.188,5.49 4.354,5.667 0.167,0.177 10 false 9 2.531,5.833 2.698,6.01 0.167,0.177 10 false 3 2.542,6.5 2.729,6.698 0.188,0.198 10 false 2 5.5,0.75 5.875,1.021 0.375,0.271 10 false IG 6.198,5.781 6.573,6.052 0.375,0.271 10 false IG 2.604,1.854 2.875,2.052 0.271,0.198 10 false 2 2.604,1.208 2.875,1.406 0.271,0.198 10 false 1 2.615,4.042 2.885,4.24 0.271,0.198 10 false 2 2.604,3.354 2.875,3.552 0.271,0.198 10 false 1 2.146,3.479 2.667,3.76 0.521,0.281 10 false HM1 2.146,4.156 2.479,4.354 0.333,0.198 10 false HM2 3.427,4.885 3.615,5.094 0.188,0.208 12 false * 3.479,5.531 3.667,5.74 0.188,0.208 12 false * 5.427,2.438 5.948,2.719 0.521,0.281 10 false RLY1-1 5.427,3.135 5.948,3.417 0.521,0.281 10 false RLY1-2 5.427,5.177 5.948,5.458 0.521,0.281 10 false RLY2-1 5.427,5.854 5.948,6.135 0.521,0.281 10 false RLY2-2

PROCEDURE

1.CHECK ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR OR LOCK SHIFT MOTOR)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.
U164489E02
1.927,2.26 2.042,2.75 false 1.594,2.729 1.656,2.26 false 1.427,1.75 1.167,1.354 false 1.167,2.688 1.417,2.271 false 2.177,1.76 2.469,1.365 false 2.229,2.229 2.667,2.698 false 1.906,2.76 2.292,2.938 0.385,0.177 10 false TM1 1.667,0.938 1.938,1.115 0.271,0.177 10 false A28 0.188,0.135 0.573,0.313 0.385,0.177 10 false *a 1.396,2.75 1.781,2.927 0.385,0.177 10 false TM2 0.844,1.198 1.229,1.375 0.385,0.177 10 false HM1 0.885,2.719 1.271,2.896 0.385,0.177 10 false HM2 2.5,1.26 2.885,1.438 0.385,0.177 10 false M1*A 2.563,2.771 2.948,2.948 0.385,0.177 10 false M2*A

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Transfer Shift Actuator Assembly (High-low Transfer Shift Motor) Side
Tester Connection Condition Specified Condition
A28-2 (HM1) or A28-6 (HM2) - Body ground Always 10 kΩ or higher

Transfer Shift Actuator Assembly (Center Differential Lock Shift Motor) Side
Tester Connection Condition Specified Condition
A28-8 (TM1) or A28-7 (TM2) - Body ground Always 10 kΩ or higher

Differential Lock Shift Actuator (Differential Lock Shift Motor) Side (w/ Rear Differential Lock)
Tester Connection Condition Specified Condition
A28-3 (M1) or A28-9 (M2) - Body ground Always 10 kΩ or higher


Text in Illustration
*A w/ Rear Differential Lock
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)

Result:
Result Proceed to
OK for LHD A
for RHD B
NG (transfer shift actuator assembly (high-low transfer shift motor) side) C
NG (transfer shift actuator assembly (center differential lock shift motor) side) D
NG (differential lock shift actuator (differential lock shift motor) side (w/ Rear Differential Lock)) E




A

B

C

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

D

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

E

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the C38 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-2 (HM1) or C38-1 (HM1) - Body ground Always 10 kΩ or higher
A28-6 (HM2) or C38-2 (HM2) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the C37 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-8 (TM1) or C37-1 (TM1) - Body ground Always 10 kΩ or higher
A28-7 (TM2) or C37-2 (TM1) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL LOCK SHIFT ACTUATOR - BODY GROUND)
a.

Disconnect the A28 4 wheel drive control ECU connector.


b.

Disconnect the f1 differential lock shift actuator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-3 (M1) or f1-3 - Body ground Always 10 kΩ or higher
A28-9 (M2) or f1-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR