Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17AC  Transfer Shift Motor Limit Switch Circuit  


DESCRIPTION

When the transfer shift actuator assembly is switching between high (H4) and low (L4), the HL1, HL2 and HL3 terminals are in one of the ON/OFF combinations listed in the table below.

Terminal Mode
HIGH (H4) Switching LOW (L4)
HL1 ON ON ←→ OFF* ←→ OFF OFF
HL2 OFF OFF OFF* ON ON
HL3 OFF ON ON* ON OFF

*: Neutral position (only for vehicles with a manual transmission)

For vehicles with a manual transmission, when conditions for switching between H4 and L4 are not met, the transfer shift actuator assembly temporarily stops at the neutral position. Afterwards, when the conditions are met, switching is performed.


A malfunction is detected depending on the combination of the 3 circuits that make up the high-low transfer limit switch.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17AC
1.

When switching between high and low (high-low transfer shift motor operating) while the ignition switch is turned to ON or directly after the ignition switch is turned to ON

2.

The combination of HL1, HL2 and HL3 does not match

3.

0.05 seconds or more (if directly after ignition switch is turned to ON, 1 second or more)

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C325621E12
5.417,0.313 5.729,0.51 0.313,0.198 10 false IG 4.698,0.771 5.01,0.969 0.313,0.198 10 false 8 4.969,0.792 5.427,0.99 0.458,0.198 10 false HL1 4.969,1.531 5.427,1.729 0.458,0.198 10 false HL2 4.979,2.219 5.438,2.417 0.458,0.198 10 false HL3 4.719,1.531 5.031,1.729 0.313,0.198 10 false 7 4.771,2.198 4.927,2.396 0.156,0.198 10 false 6 3.438,0.76 3.594,0.958 0.156,0.198 10 false 4 3.427,1.531 3.583,1.729 0.156,0.198 10 false 6 3.427,2.208 3.583,2.406 0.156,0.198 10 false 5 3.083,0.781 3.542,0.979 0.458,0.198 10 false HL1 3.094,1.531 3.552,1.729 0.458,0.198 10 false HL2 3.094,2.219 3.552,2.417 0.458,0.198 10 false HL3 2,2.563 2.833,2.75 0.833,0.188 10 false Limit Switch 0.99,2.198 1.146,2.396 0.156,0.198 10 false 7 1.219,2.198 1.833,2.396 0.615,0.198 10 false GND1 1.073,3.24 3.156,3.438 2.083,0.198 10 false Transfer Shift Actuator Assembly 1.083,3.052 1.542,3.25 0.458,0.198 10 false C38 4.708,3.24 6.354,3.438 1.646,0.198 10 false 4 Wheel Drive Control ECU 4.677,3.073 5.135,3.271 0.458,0.198 10 false A27

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

Disconnect the C38 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-8 (HL1) - C38-4 (HL1) Always Below 1 Ω
A27-7 (HL2) - C38-6 (HL2) Always Below 1 Ω
A27-6 (HL3) - C38-5 (HL3) Always Below 1 Ω
C38-7 (GND) - Body ground Always Below 1 Ω
A27-8 (HL1) or C38-4 (HL1) - Body ground Always 10 kΩ or higher
A27-7 (HL2) or C38-6 (HL2) - Body ground Always 10 kΩ or higher
A27-6 (HL3) or C38-5 (HL3) - Body ground Always 10 kΩ or higher




OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
U165680E02
2.031,1.229 2.292,1.75 false 1.813,1.229 1.802,1.802 false 1.635,1.229 1.365,1.667 false 1.594,0.208 2.052,0.385 0.458,0.177 10 false C38 2.177,1.781 2.531,1.969 0.354,0.188 10 false HL2 1.646,1.813 2,2 0.354,0.188 10 false HL3 1.125,1.76 1.479,1.948 0.354,0.188 10 false HL1 0.073,0.052 0.531,0.229 0.458,0.177 10 false *a

a.

Disconnect the C38 transfer shift actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C38-4 (HL1) - Body ground Ignition switch ON 10 to 14 V
C38-6 (HL2) - Body ground Ignition switch ON 10 to 14 V
C38-5 (HL3) - Body ground Ignition switch ON 10 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

Result:
Result Proceed to
OK A
NG for LHD B
for RHD C




A

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

B

C